Home › Drivetrain › U241E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2014.09
NM24M0E _52 Drivetrain _061696 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0300970 AUTOMATIC TRANSMISSION SYSTEM UN GENERAL/CONTROL/DETAILS F

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


SYSTEM CONTROL


a.

The electronic control system of the U241E automatic transaxle consists of the controls listed below.

System Function
Clutch Pressure Control
·

Controls the pressure that is applied directly to B1 brake and C2 clutch by actuating the shift solenoid valves (SL1, SL2) in accordance with engine ECU signals.

·

The solenoid valves SL1 and SL2 minutely control the clutch pressure in accordance with the engine output and driving conditions.


Line Pressure Optimal Control Actuates the solenoid valve SLT to control the line pressure in accordance with information from the engine ECU and the operating conditions of the transaxle.
High Response Shift Control The shift time lag has been reduced to half by the centrifugal fluid pressure canceling mechanism and clutch pressure optimal control.
Engine Torque Control Retards the engine ignition timing temporarily to improve shift feeling during up or down shifting.
Shift Control in Uphill/Downhill Traveling Controls to restrict the 4th upshift or to provide appropriate engine braking by using the engine ECU to determine whether the vehicle is traveling on uphill or downhill.
Shift Timing Control The engine ECU sends current to the solenoid valve SL1 and/or SL2 based on the signals from each sensor and shifts the gear.
Lock-up Timing Control The engine ECU sends current to the solenoid valve DSL based on signals from each sensor and engages or disengages the lock-up clutch.
"N" to "D" Squat Control When the shift lever is moved from the "N" to "D" position, the gear is temporarily shifted to the 2nd and then to the 1st to reduce vehicle squat.
Diagnosis When the engine ECU detects a malfunction, the engine ECU makes a diagnosis and memorizes the failed section.
Fail-safe Even if a malfunction is detected in the sensors or solenoids, the engine ECU effects fail-safe control to prevent the vehicle's drivability from being affected significantly.


b.

Clutch to Clutch Pressure Control

i.

A clutch to clutch pressure control is used for shifting from the 1st to 2nd gear, and from the 2nd to 3rd gear. Solenoid valves SL1 and SL2 are actuated in accordance with the signals from the engine ECU, and this output pressure is guided directly to the control valves B1 and C2 in order to regulate the line pressure that acts on the B1 brake and C2 clutch.


ii.

As a result, high response and excellent shift characteristics have been achieved.

X136172E01
0.063,0.344 0.948,0.885 0.885,0.542 10 false Signals from Various Sensors 1.896,0.406 2.698,0.604 0.802,0.198 10 false Engine ECU 3.125,0.771 3.427,0.917 0.302,0.146 9 false SL1 3.625,0.771 3.927,0.917 0.302,0.146 9 false SL2 1.938,1.25 2.656,1.604 0.719,0.354 10 false B1 Control Valve 2.667,1.229 4.25,1.417 1.583,0.188 10 false Solenoid Valve SL1 OFF 3.313,1.375 3.469,1.573 0.156,0.198 10 false ↓ 2.969,1.552 3.917,1.729 0.948,0.177 10 false B1 Brake ON 3.26,1.823 3.5,2.01 0.24,0.188 10 false B1 0.135,2.417 1.094,2.615 0.958,0.198 10 false Line Pressure 4.604,1.156 5.302,1.51 0.698,0.354 10 false C2 Control Valve 5.521,0.99 6.479,1.354 0.958,0.365 10 false Solenoid Valve SL2 OFF 5.948,1.344 6.104,1.542 0.156,0.198 10 false ↓ 5.552,1.542 6.552,1.729 1,0.188 10 false C2 Clutch ON 5.906,1.823 6.156,1.99 0.25,0.167 10 false C2



c.

Clutch Pressure Optimal Control

i.

The solenoid valve SLT is used for optimal control of clutch pressure. The engine ECU monitors the signals from various types of sensors such as the input turbine speed sensor, allowing solenoid valve SLT to minutely control the clutch pressure in accordance with engine output and driving conditions.


ii.

As a result, smooth shift characteristics have been realized.

X136138E01
0.833,1.177 2,1.375 1.167,0.198 10 false Input Shaft Speed 1.677,1.844 2.188,2.052 0.51,0.208 10 false Engine 2.313,1.677 2.677,1.854 0.365,0.177 10 false Time 2.073,1.49 3.354,1.625 1.281,0.135 7 false Practical rpm Change Ratio 2.375,0.802 3.24,1.063 0.865,0.26 7 false Target rpm Change Ratio 4.573,0.938 5.052,1.281 0.479,0.344 10 false Engine ECU 3.563,1.552 4.469,1.948 0.906,0.396 10 false Input Turbine Speed Sensor 4.031,2.104 4.354,2.281 0.323,0.177 10 false SLT 2.385,3.813 3.76,4.01 1.375,0.198 10 false Output Shaft Torque 4.01,4.104 4.396,4.302 0.385,0.198 10 false Time 5.323,3.083 6.729,3.302 1.406,0.219 10 false Solenoid Drive Signal 4.427,2.656 5.271,3.042 0.844,0.385 10 false Clutch/Brake Pressure 5.635,1.01 7.031,1.167 1.396,0.156 7 false Signals from Various Sensors 5.563,1.115 6.854,1.26 1.292,0.146 7 false Engine Speed 5.479,1.24 6.74,1.385 1.26,0.146 7 false Engine Torque Information 5.396,1.354 7.01,1.5 1.615,0.146 7 false ATF Temperature



d.

Line Pressure Optimal Control

i.

Through the use of the solenoid valve SLT, the line pressure is optimally controlled in accordance with the engine torque information, as well as with the internal operating conditions of the torque converter and the transaxle.


ii.

Accordingly, the line pressure can be controlled minutely in accordance with the engine output, traveling condition, and the ATF temperature, thus realizing smooth shift characteristics and optimizing the workload in the oil pump.

X136174E01
0.115,0.302 1.01,0.5 0.896,0.198 10 false Line Pressure 0.958,1.083 2.156,1.281 1.198,0.198 10 false Primary Regulator 0.292,3.385 0.708,3.583 0.417,0.198 10 false Pump 2.125,3.365 3.323,3.573 1.198,0.208 10 false Throttle Pressure 1.844,2.25 2.427,2.625 0.583,0.375 10 false Fluid Pressure 2.823,2.875 3.333,3.073 0.51,0.198 10 false Current 3.281,3.75 4.552,3.958 1.271,0.208 10 false Solenoid Valve SLT 4.198,1.75 5.573,1.958 1.375,0.208 10 false Solenoid Drive Signal 5.042,2.979 5.896,3.177 0.854,0.198 10 false Engine ECU 6.323,2.354 6.99,2.635 0.667,0.281 7 false Input Turbine Speed Sensor 6.323,2.656 7.135,2.813 0.813,0.156 7 false ATF Temperature 6.323,2.854 6.948,3 0.625,0.146 7 false Shift Position 6.313,3.042 7.156,3.188 0.844,0.146 6 false Throttle Valve Opening 6.333,3.24 7.094,3.385 0.76,0.146 7 false Intake Air Mass 6.323,3.427 7.125,3.563 0.802,0.135 6 false Water Temperature 6.323,3.635 6.969,3.802 0.646,0.167 7 false Engine Speed



e.

High Response Shift Control

i.

Due to the use of the previously mentioned centrifugal fluid pressure canceling mechanism and the clutch pressure optimal control, not only smooth shifting has been achieved, but the shift time lag has been halved to realize excellent response.



f.

Shift Control in Uphill/Downhill Traveling

i.

This control helps minimize the gear shifting when the driver operates the accelerator pedal while driving on a winding uphill or downhill road in order to ensure a smooth drive.


ii.

When the engine ECU detects uphill travel, it prohibits upshifting to the 4th after downshifting to the 3rd.


iii.

If a signal indicating that the driver has operated the brake pedal is input while the engine ECU detects downhill travel, it downshifts from the 4th to 3rd.

X136173E01
0.458,2.688 1.49,2.875 1.031,0.188 10 false Without Control 0.656,3.063 1.51,3.26 0.854,0.198 10 false With Control 1.542,2.615 2,2.813 0.458,0.198 10 false 4th 1.906,2.615 2.177,2.802 0.271,0.188 10 false 3rd 2.313,2.615 2.771,2.813 0.458,0.198 10 false 4th 2.833,2.604 3.104,2.792 0.271,0.188 10 false 3rd 3.333,2.604 3.792,2.802 0.458,0.198 10 false 4th 1.552,2.938 2.01,3.135 0.458,0.198 10 false 4th 2.427,2.969 2.698,3.156 0.271,0.188 10 false 3rd 3.344,2.938 3.802,3.135 0.458,0.198 10 false 4th 4.417,2.958 4.688,3.146 0.271,0.188 10 false 3rd 5.313,2.948 5.771,3.146 0.458,0.198 10 false 4th 3.885,3.448 4.99,3.625 1.104,0.177 10 false Brake Operation


iv.

The actual acceleration calculated from the speed sensor signal is compared with the reference acceleration (based on level road travel) stored in the engine ECU to determine uphill or downhill travel.

X136154E01
2.229,0.219 3.865,0.417 1.635,0.198 10 false : Reference acceleration 2.229,0.479 3.542,0.677 1.313,0.198 10 false : Actual acceleration 0.167,0.99 0.75,1.167 0.583,0.177 10 false Smaller 1.438,1.583 1.958,1.76 0.521,0.177 10 false Uphill 3.875,1.333 4.458,1.521 0.583,0.188 10 false Greater 5.323,1.583 5.948,1.75 0.625,0.167 10 false Downhill



g.

Multi-mode Automatic Transmission

i.

By moving the shift lever to the front ("+" position) or to the rear ("-" position), the driver can select the desired shift range position. Thus, the driver is able to shift gears with a manual-like feel.

·

Multi-mode automatic transmission is designed for switching the gear range; not for fixing in one gear.

·

An S mode indicator light which illuminates when the S mode position is selected and a shift range indicator light which indicates the shift range position have been provided in the combination meter.

X136171E01
2.177,0.906 2.177,1.74 false 1.021,1.021 1.979,1.208 0.958,0.188 10 false Gateway ECU 2.677,0.625 3.906,0.823 1.229,0.198 10 false Combination Meter 2.552,0.99 4.031,1.198 1.479,0.208 10 false S Mode Indicator Light 2.417,1.344 4.052,1.552 1.635,0.208 10 false Shift Range Indicator Light 1.99,1.74 2.604,1.938 0.615,0.198 10 false BEAN 1.031,1.781 1.375,1.958 0.344,0.177 10 false CAN 1.75,2.448 2.573,2.646 0.823,0.198 10 false Engine ECU 3.698,1.99 4.677,2.198 0.979,0.208 10 false Shift-up Signal 3.635,2.365 4.781,2.573 1.146,0.208 10 false Shift-down Signal 3.396,2.719 4.927,2.917 1.531,0.198 10 false S Mode Position Signal 4.917,2.344 6.25,2.708 1.333,0.365 10 false Transmission Control Switch 0.25,3.49 1.271,3.865 1.021,0.375 10 false Ignition Advance Control Signal 1.708,3.49 2.635,3.906 0.927,0.417 10 false Fluid Pressure Control Signal 3.188,3.521 4.146,3.958 0.958,0.438 10 false Solenoid Valve Control Signal 1.354,4.5 1.927,4.708 0.573,0.208 10 false Engine 2.833,4.729 3.292,4.927 0.458,0.198 10 false A/T



ii.

The driver selects the S mode position by moving the shift lever. At this time, the shift range position is selected to the 3 range. Then, the shift range position is changed by one as the driver moves the shift lever to the front ("+" position) or to the rear ("-" position).


iii.

Under this control, the engine ECU effects optimal shift control within the usable gear range that the driver has selected. As with the ordinary automatic transmission, it shifts to the 1st gear when the vehicle is stopped.


iv.

When the shift lever is in the S mode position, the S mode indicator light in the combination meter illuminates. The shift range indicator light indicates the shift range position that the driver has selected.

X136141E01
2,1.344 3.115,1.698 1.115,0.354 10 false Transition of Shift Range Positions 3.281,1.656 4.375,1.833 1.094,0.177 10 false S Mode Position 2.052,4.031 3.438,4.24 1.385,0.208 10 false : Default Shift Range 4.24,3.448 5.135,3.656 0.896,0.208 10 false Shift Pattern

Shift Range Indicator Light Indication Shift Range Usable Gear
4 S4 1st to 4th
3 S3 1st to 3rd
2 S2 1st to 2nd
1 S1 1st



h.

Shift Lock System

i.

On the models without the smart entry & start system, the key interlock device prevents the key from being pulled out after the ignition switch is turned OFF, unless the shift lever is moved to the P position. Thus, the driver is urged to park the vehicle in the P position.


ii.

The shift lock mechanism prevents the shift lever from being moved to a position other than the P position, unless the ignition switch is ON*1 or the engine switch is selected to the IG-ON mode*2, and the brake pedal is depressed. It prevents the vehicle from starting off suddenly.


iii.

The shift lock ECU uses the P detection switch to detect the shift lever position, and receives input signals from the stop light switch and ignition switch*1 or engine switch*2. Upon receiving these signals, the shift lock ECU turns ON the key interlock solenoid*1 and the shift lock solenoid in order to release the key interlock and shift lock.


iv.

A shift lock override button, which manually overrides the shift lock mechanism, is used.

X136139E01
1.052,0.729 2.198,0.927 1.146,0.198 10 false Stop Light Switch 1.031,1.573 2.125,1.792 1.094,0.219 10 false Ignition Switch*1 1.021,1.802 2.115,2.01 1.094,0.208 10 false Engine Switch*2 3.125,1.292 4.281,1.49 1.156,0.198 10 false Shift Lock ECU 5.281,0.729 6.167,1.125 0.885,0.396 10 false Key Interlock Solenoid*1 5.26,1.771 5.917,2.156 0.656,0.385 10 false Shift Lock Solenoid 3.333,3.125 4.104,3.542 0.771,0.417 10 false P Detection Switch

*1: Models without Smart Entry & Start System

*2: Models with Smart Entry & Start System



v.

The shift lock can be released by depressing the shift lock release button.

V118523E01
1.802,1.49 2.281,0.323 2.281,0.323 2.563,0.323 true 1.781,1.729 2.396,3.427 2.396,3.427 2.677,3.427 true 2.594,0.229 3.885,0.427 1.292,0.198 10 false Shift Lever Housing 2.792,3.344 4.448,3.563 1.656,0.219 10 false Shift Lock Release Button




CONSTRUCTION


a.

TORQUE CONVERTER

i.

These torque converters have optimally designed fluid passages and impeller configuration, resulting in substantially enhanced torque ratio and transmission efficiency to ensure good starting, acceleration and fuel economy.


ii.

Furthermore, a hydraulically operated lock-up mechanism which cuts power transmission losses due to slippage at medium and high speeds is used.

X136162E01
2.646,2.521 2.76,2.521 2.76,2.521 3.406,2.104 true 2.292,1.396 2.406,1.396 2.406,1.396 3.115,1.76 true 2.375,0.906 2.49,0.906 2.49,0.906 3.417,1.208 true 2.781,0.396 2.896,0.396 2.896,0.396 3.302,0.865 true 3.531,0.833 3.938,0.292 3.938,0.292 4.042,0.292 true 3.948,0.906 4.521,1.365 4.521,1.365 4.625,1.365 true 1.854,0.302 2.885,0.521 1.031,0.219 10 false Pump Impeller 4.083,0.177 5.24,0.375 1.156,0.198 10 false Turbine Runner 4.667,1.271 5.688,1.479 1.021,0.208 10 false Lock-up Clutch 1.969,0.813 2.417,1.052 0.448,0.24 10 false Stator 1.583,1.313 2.354,1.5 0.771,0.188 10 false Input Shaft 1.656,2.427 2.698,2.615 1.042,0.188 10 false One-way Clutch



b.

OIL PUMP

i.

The oil pump is combined with torque converter, lubricates the planetary gear units and supplies operating pressure to the hydraulic control.

X136169E01
2.542,0.875 2.542,1.26 true 3.74,0.979 3.74,1.365 true 3.417,1.75 3.417,2.427 true 4.063,1.438 4.063,2.135 true 2.177,0.688 3.042,0.906 0.865,0.219 10 false Pump Body 3.427,0.823 4.198,1.031 0.771,0.208 10 false Drive Gear 3.083,2.406 3.979,2.604 0.896,0.198 10 false Driven Gear 3.688,2.115 4.729,2.313 1.042,0.198 10 false Stator Shaft



c.

ATF (AUTOMATIC TRANSMISSION FLUID) TYPE WS

i.

The ATF Type WS is used to reduce the resistance of the ATF and ensure fuel economy by reducing its viscosity in the practical operation range. At the high-temperature end, its viscosity is the same as that of the ATF Type T-IV, which ensures the durability of the automatic transaxle.


ii.

There is no interchangeability between the ATF Type WS and other types of ATFs (ATF Type T-IV, D-II).

X136170E01
2.344,1.198 2.781,0.885 2.781,0.885 2.885,0.885 true 5.313,0.292 6.365,0.49 1.052,0.198 10 false : ATF Type T-IV 5.313,0.479 6.313,0.677 1,0.198 10 false : ATF Type WS 2.927,0.802 4.219,1.01 1.292,0.208 10 false Reduced Viscosity 1.74,0.969 2.115,1.188 0.375,0.219 10 false High 3.948,2.229 4.333,2.427 0.385,0.198 10 false High 0.781,1.417 1.531,1.667 0.75,0.25 10 false Viscosity

HINT:

The color of the ATF level gauge used in the ATF Type WS has been changed to black. (Orange was used in the ATF Type T-IV on the previous model.)




d.

PLANETARY GEAR UNIT

i.

The counter drive and driven gears are placed in front of the front planetary gear and under drive (U/D) planetary gear unit is placed above the counter shaft. Furthermore, the number of the brake and one-way clutch is minimized to realize the compact and high-capacity structure.


ii.

A centrifugal fluid pressure canceling mechanism is used in the C2 and C3 clutches that are applied when shifting from 2nd to 3rd and from 3rd to 4th.

X136163E01
3.469,1.125 3.469,0.656 3.469,0.656 3.583,0.656 true 4.375,1.083 4.844,0.479 4.844,0.479 4.958,0.479 true 4.896,1.521 5.167,1.854 5.167,1.854 5.281,1.854 true 4.354,2.771 4.938,3.479 4.938,3.479 5.052,3.479 true 3.677,1.938 3.802,1.938 3.802,1.938 3.979,1.573 true 3.438,2.469 3.438,2.771 3.438,2.771 3.552,2.771 true 2.917,2.656 3.271,3.458 3.271,3.458 3.385,3.458 true 1.927,1.948 2.052,1.948 2.052,1.948 2.51,1.698 true 5.625,1.427 5.771,1.094 5.771,1.094 5.885,1.094 true 1.906,0.74 2.146,0.906 0.24,0.167 10 false B1 2.24,0.719 2.427,0.875 0.188,0.156 8 false F1 2.823,0.74 3.031,0.896 0.208,0.156 10 false B2 1.719,1.031 2.031,1.229 0.313,0.198 10 false C2 3.615,0.573 4.604,0.917 0.99,0.344 10 false Front Planetary Gear 5.01,0.396 6.25,0.615 1.24,0.219 10 false Counter Drive Gear 5.01,0.76 5.323,0.958 0.313,0.198 10 false C1 5.958,1.01 6.708,1.208 0.75,0.198 10 false Input Shaft 5.344,1.76 6.667,1.969 1.323,0.208 10 false Intermediate Shaft 3.052,1.844 3.76,2.021 0.708,0.177 10 false Sun Gear 0.99,1.844 1.958,2.24 0.969,0.396 10 false Rear Planetary Gear 2.24,2.958 2.521,3.135 0.281,0.177 8 false F2 2.542,2.927 2.854,3.125 0.313,0.198 10 false B3 3.458,3.385 4.75,3.583 1.292,0.198 10 false U/D Planetary Gear 3.583,2.688 4.26,2.875 0.677,0.188 10 false Sun Gear 5.146,3.396 6.51,3.604 1.365,0.208 10 false Counter Driven Gear 5.646,2.875 6.406,3.094 0.76,0.219 10 false Ring Gear 5.604,2.198 6.615,2.563 1.01,0.365 10 false Differential Drive Pinion

Component Function
C1 Forward Clutch Connects input shaft and front planetary sun gear.
C2 Direct Clutch Connects intermediate shaft and rear planetary sun gear.
C3 U/D Direct Clutch Connects U/D sun gear and U/D planetary carrier.
B1 2nd Brake Prevents rear planetary sun gear from turning clockwise or counterclockwise.
B2 1st & Reverse Brake Prevents rear planetary carrier and front planetary ring gear from turning clockwise or counterclockwise.
B3 U/D Brake Prevents U/D planetary sun gear from turning clockwise or counterclockwise.
F1 No. 1 One-way Clutch Prevents front planetary ring gear and rear planetary carrier from turning counterclockwise.
F2 U/D One-way Clutch Prevents U/D planetary sun gear from turning clockwise.
Planetary Gears These gears change the route through which driving force is transmitted, in accordance with the operation of each clutch and brake, in order to increase or reduce the input and output speed.



e.

Centrifugal Fluid Pressure Canceling Mechanism

i.

There are two reasons for improving the conventional clutch mechanism:

·

To prevent the generation of pressure by the centrifugal force that applied to the fluid in piston fluid pressure chamber (hereafter referred to as "chamber A") when the clutch is released, a check ball is provided to discharge the fluid. Therefore, before the clutch can be subsequently applied, it took time for the fluid to fill the chamber A.

·

During shifting, in addition to the original clutch pressure that is controlled by the valve body, the pressure that acts on the fluid in the chamber A also exerts influence, which is dependent upon revolution fluctuations.



ii.

To address these two needs for improvement, a canceling fluid pressure chamber (hereafter referred to as "chamber B") has been provided opposite chamber A.

X136164E01
1.719,0.26 1.802,0.26 1.802,0.26 2.052,1.021 true 1.219,0.875 1.302,0.875 1.302,0.875 1.656,1.438 true 1.5,1.625 2.073,1.531 2.073,1.531 1.719,2.031 true 1.302,1.521 1.083,2.552 1.083,2.552 1.427,2.146 true 4.438,3.073 4.333,3.073 4.333,3.073 4.125,2.375 true 3.781,0.229 3.677,0.229 3.677,0.229 3.677,0.979 true 1.063,0.177 1.802,0.354 0.74,0.177 10 false C2 Clutch 0.802,0.771 1.344,0.969 0.542,0.198 10 false Piston 1.917,1.344 2.688,1.542 0.771,0.198 10 false Chamber B 0.792,2.552 1.573,2.74 0.781,0.188 10 false Chamber A 3.823,0.135 5.073,0.354 1.25,0.219 10 false C2 Clutch Portion 4.479,2.979 5.729,3.188 1.25,0.208 10 false C3 Clutch Portion


iii.

By utilizing the lubrication fluid such as that of the shaft, the same amount of centrifugal force is applied, thus canceling the centrifugal force that is applied to the piston itself. Accordingly, it is not necessary to discharge the fluid through the use of a check ball, and a highly responsive and smooth shifting characteristic has been achieved.

X136039E01
3.375,2.01 4.188,2.188 0.813,0.177 0.573,2.26 6.781,2.729 6.208,0.469 3.969,0.573 4.063,0.573 4.063,0.573 4.063,0.833 true 3.094,0.958 3.177,0.406 false 3.135,1.219 3.177,0.427 3.177,0.427 3.219,1.458 false 2.938,1.219 1.958,1.104 1.958,1.104 2.979,1.479 false 2.865,0.969 1.99,1.104 false 4.396,1.021 3.542,0.979 false 3.49,1.208 4.375,1.021 4.375,1.021 3.448,1.469 false 4.385,1.615 4.26,1.615 4.26,1.615 3.635,1.5 true 2.573,1.521 2.375,1.719 2.375,1.719 2.271,1.719 true 2.958,1.635 2.958,1.75 2.958,1.75 3.188,1.75 false 3.021,1.75 3.24,1.75 3.24,1.75 3.24,1.646 false 3.115,1.75 2.948,2.01 2.948,2.01 2.844,2.01 true 2.063,0.073 3.688,0.448 1.625,0.375 10 false Centrifugal Fluid Pressure applied to the Chamber A 4.219,0.219 4.698,0.396 0.479,0.177 10 false Clutch 3.542,0.458 4.01,0.625 0.469,0.167 10 false Piston 0.615,1 2.021,1.24 1.406,0.24 10 false Target Fluid Pressure 0.104,1.625 2.313,1.854 2.208,0.229 10 false Chamber A (Piston Fluid Pressure) 0.854,1.917 2.875,2.146 2.021,0.229 10 false Fluid Pressure applied to Piston 4.458,0.927 6.052,1.281 1.594,0.354 10 false Centrifugal Fluid Pressure applied to Chamber B 4.448,1.521 6.854,1.729 2.406,0.208 10 false Chamber B (Canceling Fluid Pressure) 3.469,2.01 4.167,2.177 0.698,0.167 10 false Shaft Side 0.854,2.302 2.26,2.646 1.406,0.344 10 false Fluid pressure applied to piston 2.813,2.302 4.344,2.688 1.531,0.385 10 false Centrifugal fluid pressure applied to chamber B 4.813,2.302 6.615,2.667 1.802,0.365 10 false Target fluid pressure (original clutch pressure) 2.396,2.396 2.552,2.594 0.156,0.198 10 false - 4.521,2.427 4.677,2.625 0.156,0.198 10 false =



f.

VALVE BODY UNIT

i.

The valve body consists of the upper and lower valve bodies and 5 solenoid valves. Apply orifice control, which controls the flow volume to the B3 brake, is used.

X102817C01
2.833,0.385 2.135,0.385 true 4.969,0.146 4.802,0.146 4.802,0.146 4,0.5 true 5.729,0.833 5.031,0.833 true 5.865,1.323 5.167,1.323 true 5.615,1.99 4.917,1.99 true 2.281,2.031 1.875,2.031 true 3.115,2.344 3.115,1.844 true 3.458,2.344 3.458,1.969 true 5.021,0.052 5.344,0.292 0.323,0.24 10 *2 5.771,0.729 6.094,0.969 0.323,0.24 10 *8 5.885,1.219 6.208,1.458 0.323,0.24 10 *7 5.656,1.896 5.979,2.135 0.323,0.24 10 *6 3.396,2.385 3.719,2.625 0.323,0.24 10 *5 3.042,2.375 3.365,2.615 0.323,0.24 10 *4 1.698,1.938 2.021,2.177 0.323,0.24 10 *3 1.948,0.281 2.271,0.521 0.323,0.24 10 *1
*1 Shift Solenoid Valve SL1 *2 Shift Solenoid Valve SLT
*3 Shift Solenoid Valve SL2 *4 Shift Solenoid Valve DSL
*5 Shift Solenoid Valve S4 *6 ATF Temperature Sensor
*7 Lower Valve Body *8 Upper Valve Body


Upper Valve Body
X102819C02
3.146,0.698 3.146,0.115 3.146,0.115 3.01,0.115 true 3.448,0.865 3.448,0.104 3.448,0.104 3.594,0.104 true 4.083,0.833 4.083,0.104 4.083,0.104 4.229,0.104 true 3.479,2 3.479,2.417 true 2.74,1.563 2.135,1.563 true 4.5,0.677 4.854,0.135 4.854,0.135 5.104,0.135 true 3.167,2 3.167,2.417 true 3.833,1.729 3.833,2.417 true 4.51,1.833 4.51,2.438 true 2.844,0.021 3.063,0.229 0.219,0.208 10 false *1 3.656,0.021 3.875,0.229 0.219,0.208 10 false *2 4.292,0.021 4.51,0.229 0.219,0.208 10 false *3 5.156,0.052 5.375,0.26 0.219,0.208 10 false *4 4.458,2.469 4.677,2.677 0.219,0.208 10 false *9 3.781,2.469 4,2.677 0.219,0.208 10 false *8 3.417,2.469 3.635,2.677 0.219,0.208 10 false *7 3.094,2.469 3.313,2.677 0.219,0.208 10 false *6 1.948,1.479 2.167,1.688 0.219,0.208 10 false *5
*1 Lock-up Relay Valve *2 Lock-up Control Valve
*3 2nd Regulator Valve *4 C2 Lock Valve
*5 Solenoid Modulator Valve *6 B3 Orifice Control Valve
*7 B1 Lock Valve *8 Clutch Apply Control Valve
*9 C2 Exhaust Check Valve - -


Lower Valve Body
X102820C02
3.5,1.021 3.5,2.573 3.5,2.573 3.344,2.573 true 2.385,0.135 3.219,0.135 3.219,0.135 3.219,0.5 true 3.698,1.76 3.698,2.594 3.698,2.594 3.844,2.594 true 4.042,0.646 4.948,0.646 true 2.156,0.698 2.948,0.698 true 1.969,0.604 2.229,0.813 0.26,0.208 10 false *1 3.167,2.49 3.427,2.698 0.26,0.208 10 false *3 3.885,2.5 4.146,2.708 0.26,0.208 10 false *5 5.01,0.542 5.271,0.75 0.26,0.208 10 false *4 2.208,0.042 2.469,0.25 0.26,0.208 10 false *2
*1 3-4 Shift Valve *2 B1 Control Valve
*3 B2 Control Valve *4 C2 Control Valve
*5 Primary Regulator Valve - -




g.

Solenoid Valves

i.

In order to provide a hydraulic pressure that is proportion to current that flows to the solenoid coil, the solenoid valves SL1, SL2, and SLT linearly control the line pressure and clutch and brake engagement pressure based on the signals from the engine ECU. The solenoid valves SL1, SL2, and SLT have the same basic structure.

X136160E01
2.573,1.01 2.677,0.531 2.677,0.531 2.771,0.531 true 1.521,1.115 1.365,0.542 1.365,0.542 1.26,0.542 true 1.844,1.292 1.573,1.823 1.573,1.823 1.469,1.823 true 0.833,0.448 1.75,0.646 0.917,0.198 10 false Sleeve 2.802,0.448 3.719,0.635 0.917,0.188 10 false Solenoid Coil 0.719,1.729 1.51,1.906 0.792,0.177 10 false Spool Valve 3.615,0.865 4.229,1.302 0.615,0.438 10 false Hydraulic Pressure 4.917,2.115 5.469,2.292 0.552,0.177 10 false Current

Function of Shift Solenoid Valves SL1, SL2, and SLT
Shift Solenoid Valve Action Function
SL1 Clutch and brake engagement pressure control
·

B1 brake pressure control

·

Lock-up clutch pressure control


SL2 C2 clutch pressure control
SLT Line pressure control
·

Line pressure control

·

Secondary pressure control





h.

Solenoid Valves S4 and DSL

i.

The solenoid valves S4 and DSL use a three-way solenoid valve.

X136153E01
4.688,0.615 4.781,0.615 4.781,0.615 4.875,1.01 false 0.948,0.813 2.073,0.979 1.125,0.167 10 false Control Pressure 0.24,1.427 1.135,1.604 0.896,0.177 10 false Line Pressure 1.865,2.333 3.125,2.521 1.26,0.188 10 false Solenoid Valve ON 4.406,2.375 5.771,2.583 1.365,0.208 10 false Solenoid Valve OFF 4.313,0.531 4.677,0.708 0.365,0.177 10 false Drain


ii.

The solenoid valve S4 when set to ON controls the 3-4 shift valve to establish the 4th by changing over the fluid pressure applied to B3 brake and C3 clutch.

X106867E04
2.448,0.469 3.594,0.677 1.146,0.208 10 false Solenoid Valve S4 5.073,1.646 6.719,1.833 1.646,0.188 10 false B3 Brake On (Except 4th) 5.104,2.146 6.365,2.354 1.26,0.208 10 false C3 Clutch On (4th) 3.281,1.771 3.938,1.969 0.656,0.198 10 false S4 OFF 3.281,2.229 3.938,2.427 0.656,0.198 10 false S4 ON 4.375,0.802 5.448,1.01 1.073,0.208 10 false B3 Accumulator 2.552,2.667 3.531,2.875 0.979,0.208 10 false 3-4 Shift Valve 1.448,1.885 2.49,2.094 1.042,0.208 10 false Line Pressure 0.646,0.99 1.688,1.198 1.042,0.208 10 false Line Pressure 4.385,2.885 5.458,3.094 1.073,0.208 10 false C3 Accumulator


iii.

The solenoid valve DSL controls the B2 control valve via the C2 lock valve when the transaxle is shifted in the R or L position. During lock-up, the lock-up relay valve is controlled via the C2 lock valve.

X136167E01
3.969,0.313 5.302,0.49 1.333,0.177 10 false Lock-up Relay Valve 3.844,0.781 4.135,0.948 0.292,0.167 10 false "R" 3.417,1.573 4.125,1.938 0.708,0.365 10 false Secondary Pressure 0.729,1.667 2.052,1.865 1.323,0.198 10 false Solenoid Valve DSL 2.271,1.667 3.292,1.865 1.021,0.198 10 false C2 Lock Valve 4.156,3.281 4.448,3.448 0.292,0.167 10 false "R" 4.167,3.542 4.438,3.719 0.271,0.177 10 false "L" 5.625,1.104 7.021,1.302 1.396,0.198 10 false Lock-up ON Chamber 5.635,2.271 7.083,2.5 1.448,0.229 10 false Lock-up OFF Chamber 6.271,3.5 6.583,3.698 0.313,0.198 10 false B2 4.302,4.24 5.385,4.438 1.083,0.198 10 false B2 Control Valve 3.208,3.635 3.927,4.031 0.719,0.396 10 false Secondary Pressure



i.

Apply Orifice Control

i.

This control is effected by the B3 orifice control valve. The B3 orifice control valve has been provided for the B3 brake, which is applied when shifting from the 4th to 3rd. The B3 orifice control valve is controlled by the amount of the line pressure in accordance with shifting conditions, and the flow volume of the fluid that is supplied to the B3 brake is controlled by varying the size of the control valve's apply orifice.

X106866E03
4.917,1.896 5.99,2.167 1.073,0.271 10 false B3 Accumulator 3.656,0.583 5.813,0.865 2.156,0.281 10 false B3 Orifice Control Valve 0.708,2.177 2.302,2.458 1.594,0.281 10 false B3 Apply Fluid Pressure 2.156,0.26 3.125,0.542 0.969,0.281 10 false Line Pressure 5.333,1.198 6.958,1.396 1.625,0.198 10 false B3 Brake ON (Except 4th)



j.

ATF Temperature Sensor

i.

The ATF temperature sensor is installed in the lower valve body for direct detection of the fluid temperature.


ii.

The ATF temperature sensor is used for correction of clutch and brake pressure to keep smooth shift quality every time.

X136168E01
2.333,2.198 2.458,2.198 2.458,2.198 2.74,1.573 true 4.406,2.01 4.948,1.802 4.948,1.802 5.063,1.802 true 1.208,2.104 2.396,2.302 1.188,0.198 10 false Lower Valve Body 5.125,1.729 6.75,1.927 1.625,0.198 10 false ATF Temperature Sensor



k.

Input Turbine Speed Sensor and Counter Gear Speed Sensor

i.

The U241E automatic transaxle uses an input turbine speed sensor (for the NT signal) and a counter gear speed sensor (for the NC signal). Thus, the engine ECU can detect the timing of the shifting of the gears and appropriately control the engine torque and hydraulic pressure in response to the various conditions.

·

The input turbine speed sensor detects the input speed of the transaxle. The direct clutch (C2) drum is used as the timing rotor for this sensor.

·

The counter gear speed sensor detects the speed of the counter gear. The counter drive gear is used as the timing rotor for this sensor.

X136158E01
2.594,0.281 2.708,0.281 2.708,0.281 2.708,0.667 true 3.469,0.698 3.469,0.281 3.469,0.281 3.573,0.281 true 3.458,1.01 4.958,0.792 4.958,0.792 5.063,0.792 true 1.906,0.792 2.021,0.792 2.021,0.792 2.677,0.99 true 0.552,0.188 2.635,0.396 2.083,0.208 10 false Input Turbine Speed Sensor (NT) 0.396,0.708 1.906,0.917 1.51,0.208 10 false Direct Clutch (C2) Drum 3.615,0.188 5.771,0.385 2.156,0.198 10 false Counter Gear Speed Sensor (NC) 5.104,0.719 6.417,0.906 1.313,0.188 10 false Counter Drive Gear




l.

SHIFT CONTROL MECHANISM

i.

A gate type shift lever that uses a shift control cable is used. For the gate type, the shift lever button and the overdrive switch of the straight type shift lever have been discontinued. Similar functions are achieved through a single-shift operation (fore-aft and side-to-side).


ii.

A shift lock system that consisting of the key interlock device*1 and shift lock mechanism is used.

X136144E01
3.354,2.427 3.833,0.417 3.833,0.417 3.927,0.417 true 4.073,2.802 5.417,4.427 5.417,4.427 5.51,4.427 true 3.771,2.646 4.323,5.073 4.323,5.073 4.417,5.073 true 2.24,3.229 2.667,4.771 2.667,4.771 2.76,4.771 true 4,0.333 5.083,0.542 1.083,0.208 10 false Ignition Switch*1 4.01,0.5 5.552,0.698 1.542,0.198 10 false ● Key Interlock Solenoid 5.563,4.365 6.667,4.573 1.104,0.208 10 false Shift Lock ECU 5.625,4.5 6.99,4.719 1.365,0.219 10 false ● P Detection Switch 4.458,5.01 5.781,5.219 1.323,0.208 10 false Shift Lock Solenoid 4.5,5.156 6.438,5.354 1.938,0.198 10 false ● Transmission Control Switch 2.802,4.688 4.01,4.896 1.208,0.208 10 false Stop Light Switch 0.344,5.229 3.302,5.438 2.958,0.208 10 false *1: Models without Smart Entry & Start System 0.333,5.479 3.115,5.688 2.781,0.208 10 false *2: Models with Smart Entry & Start System



m.

Key Interlock Solenoid (Models without Smart Entry & Start System)

i.

The activation of the key interlock solenoid that is mounted on the upper column bracket moves the lock pin to restrict the movement of the key cylinder. Therefore, if the shift lever is moved to any position other than "P", the ignition key cannot be moved from the "ACC" to the "LOCK" position.

X136142




OPERATION


a.

Transaxle Power Flow

V118451E01
0.344,0.156 0.896,0.677 0.552,0.521 10 false Shift Lever Position 1.083,0.167 1.438,0.375 0.354,0.208 10 false Gear 1.969,0.167 2.917,0.354 0.948,0.188 10 false Solenoid Valve 3.781,0.167 4.229,0.354 0.448,0.188 10 false Clutch 5.094,0.156 5.542,0.344 0.448,0.188 10 false Brake 6.125,0.156 6.708,0.5 0.583,0.344 10 false One-way Clutch 1.094,1.135 1.448,1.344 0.354,0.208 10 false Park 1.01,1.438 1.531,1.635 0.521,0.198 10 false Reverse 1.031,1.74 1.552,1.938 0.521,0.198 10 false Neutral 1.167,2.042 1.406,2.229 0.24,0.188 10 false 1st 1.167,2.344 1.406,2.531 0.24,0.188 10 false 2nd 1.177,2.646 1.417,2.833 0.24,0.188 10 false 3rd 1.177,2.948 1.417,3.135 0.24,0.188 10 false 4th 1.177,3.26 1.417,3.448 0.24,0.188 10 false 1st 1.177,3.563 1.417,3.75 0.24,0.188 10 false 2nd 1.177,3.865 1.417,4.052 0.24,0.188 10 false 3rd 1.177,4.177 1.417,4.365 0.24,0.188 10 false 4th 1.167,4.479 1.406,4.667 0.24,0.188 10 false 1st 1.177,4.781 1.417,4.969 0.24,0.188 10 false 2nd 1.177,5.083 1.417,5.271 0.24,0.188 10 false 3rd 1.167,5.396 1.406,5.583 0.24,0.188 10 false 1st 1.177,5.698 1.417,5.885 0.24,0.188 10 false 2nd 1.167,6.01 1.406,6.198 0.24,0.188 10 false 1st 0.333,6.375 1.031,6.573 0.698,0.198 9 false : Operation 1.135,6.385 1.969,6.563 0.833,0.177 9 false : Lock-up ON

i.

1st Gear (Shift Lever in D or S4, S3 and S2 Ranges)

X136147C01
1.438,2.406 1.792,2.406 1.792,2.406 1.99,2.104 true 3.375,1.323 3.583,0.99 3.583,0.99 3.865,0.99 true 4.708,1.188 5.104,0.49 5.104,0.49 5.385,0.49 true 5.375,1.854 5.677,2.302 5.677,2.302 5.958,2.302 true 2.635,3.49 2.938,3.938 2.938,3.938 3.219,3.938 true 4.646,3.646 4.948,4.094 4.948,4.094 5.229,4.094 true 6.479,1.802 6.875,1.802 true 6.26,3.083 6.656,3.083 true 6.271,3.885 6.667,3.885 true 1.229,2.313 1.417,2.479 0.188,0.167 10 false *1 3.917,0.896 4.125,1.094 0.208,0.198 10 false *2 5.438,0.396 5.656,0.594 0.219,0.198 10 false *3 5.99,2.229 6.302,2.385 0.313,0.156 10 false *4 6.885,1.708 7.083,1.917 0.198,0.208 10 false *5 3.281,3.875 3.458,4.073 0.177,0.198 10 false *6 5.281,4.021 5.5,4.198 0.219,0.177 10 false *7 6.698,2.99 6.917,3.167 0.219,0.177 10 false *8 6.698,3.771 6.854,3.958 0.156,0.188 10 false *9
*1 Rear Planetary Gear *2 Front Planetary Gear
*3 Counter Drive Gear *4 Intermediate Shaft
*5 Input Shaft *6 U/D Planetary Gear
*7 Counter Driven Gear *8 Differential Drive Pinion
*9 Ring Gear - -



ii.

2nd Gear (Shift Lever in D or S4, S3 and S2 Ranges)

X136148C01
1.552,2.385 1.844,2.385 1.844,2.385 1.969,2.125 true 3.396,1.333 3.594,0.979 3.594,0.979 3.813,0.979 true 4.677,1.219 5.052,0.479 5.052,0.479 5.271,0.479 true 5.323,1.854 5.583,2.313 5.583,2.313 5.802,2.313 true 2.615,3.479 2.875,3.938 2.875,3.938 3.094,3.938 true 4.656,3.646 4.917,4.104 4.917,4.104 5.135,4.104 true 6.448,1.802 6.833,1.802 true 6.24,3.094 6.625,3.094 true 6.25,3.844 6.635,3.844 true 1.365,2.281 1.552,2.469 0.188,0.188 10 false *1 3.823,0.885 4,1.083 0.177,0.198 10 false *2 5.333,0.385 5.646,0.542 0.313,0.156 10 false *3 5.833,2.229 6,2.417 0.167,0.188 10 false *4 6.854,1.698 7.042,1.906 0.188,0.208 10 false *5 3.125,3.844 3.438,4 0.313,0.156 10 false *6 5.167,4.031 5.479,4.188 0.313,0.156 10 false *7 6.656,3 6.969,3.156 0.313,0.156 10 false *8 6.667,3.75 6.979,3.906 0.313,0.156 10 false *9
*1 Rear Planetary Gear *2 Front Planetary Gear
*3 Counter Drive Gear *4 Intermediate Shaft
*5 Input Shaft *6 U/D Planetary Gear
*7 Counter Driven Gear *8 Differential Drive Pinion
*9 Ring Gear - -



iii.

3rd Gear (Shift Lever in D or S4 and S3 Ranges)

X136149C01
1.563,2.531 1.865,2.531 1.865,2.531 1.979,2.115 true 6.448,1.813 6.729,1.813 true 6.229,3.083 6.51,3.083 true 6.229,3.885 6.51,3.885 true 3.427,1.313 3.667,0.865 3.667,0.865 3.906,0.865 true 4.667,1.229 4.938,0.594 4.938,0.594 5.177,0.594 true 5.354,1.844 5.594,2.354 5.594,2.354 5.833,2.354 true 2.615,3.458 2.854,3.969 2.854,3.969 3.094,3.969 true 4.677,3.656 4.917,4.167 4.917,4.167 5.156,4.167 true 1.333,2.438 1.646,2.594 0.313,0.156 10 false *1 3.958,0.76 4.271,0.917 0.313,0.156 10 false *2 5.208,0.51 5.521,0.667 0.313,0.156 10 false *3 5.875,2.292 6.188,2.448 0.313,0.156 10 false *4 6.75,1.719 7.063,1.875 0.313,0.156 10 false *5 3.125,3.917 3.438,4.073 0.313,0.156 10 false *6 5.208,4.094 5.521,4.25 0.313,0.156 10 false *7 6.542,2.99 6.854,3.146 0.313,0.156 10 false *8 6.552,3.802 6.865,3.958 0.313,0.156 10 false *9
*1 Rear Planetary Gear *2 Front Planetary Gear
*3 Counter Drive Gear *4 Intermediate Shaft
*5 Input Shaft *6 U/D Planetary Gear
*7 Counter Driven Gear *8 Differential Drive Pinion
*9 Ring Gear - -



iv.

4th Gear (Shift Lever in D or S4 Range)

X136150C01
1.604,2.552 1.865,2.552 1.865,2.552 2.042,2.198 true 6.427,1.844 6.76,1.844 true 6.208,3.073 6.542,3.073 true 6.208,3.875 6.542,3.875 true 3.375,1.354 3.573,0.885 3.573,0.885 3.823,0.885 true 4.677,1.25 5.01,0.521 5.01,0.521 5.26,0.521 true 5.365,1.896 5.667,2.396 5.667,2.396 5.917,2.396 true 2.594,3.49 2.896,3.99 2.896,3.99 3.146,3.99 true 4.656,3.656 4.958,4.156 4.958,4.156 5.208,4.156 true 1.406,2.49 1.594,2.646 0.188,0.156 10 false *1 3.885,0.813 4.198,0.969 0.313,0.156 10 false *2 5.313,0.458 5.552,0.615 0.24,0.156 10 false *3 5.948,2.313 6.26,2.469 0.313,0.156 10 false *4 6.771,1.76 7.083,1.917 0.313,0.156 10 false *5 6.573,3 6.885,3.156 0.313,0.156 10 false *6 6.583,3.792 6.896,3.948 0.313,0.156 10 false *7 3.208,3.906 3.521,4.063 0.313,0.156 10 false *8 5.26,4.073 5.573,4.229 0.313,0.156 10 false *9
*1 Rear Planetary Gear *2 Front Planetary Gear
*3 Counter Drive Gear *4 Intermediate Shaft
*5 Input Shaft *6 U/D Planetary Gear
*7 Counter Driven Gear *8 Differential Drive Pinion
*9 Ring Gear - -



v.

1st Gear (Shift Lever in S1 Range)

X136151C01
1.563,2.542 1.865,2.542 1.865,2.542 2.031,2.198 true 6.427,1.802 6.719,1.802 true 6.177,3.063 6.469,3.063 true 6.188,3.844 6.479,3.844 true 3.375,1.333 3.625,0.844 3.625,0.844 3.917,0.844 true 4.667,1.229 4.938,0.521 4.938,0.521 5.229,0.521 true 5.365,1.875 5.604,2.313 5.604,2.313 5.896,2.313 true 2.573,3.49 2.813,3.927 2.813,3.927 3.104,3.927 true 4.667,3.646 4.906,4.083 4.906,4.083 5.198,4.083 true 1.375,2.479 1.573,2.635 0.198,0.156 10 false *1 3.958,0.75 4.271,0.906 0.313,0.156 10 false *2 5.281,0.438 5.594,0.594 0.313,0.156 10 false *3 5.958,2.24 6.271,2.396 0.313,0.156 10 false *4 6.729,1.719 7.042,1.875 0.313,0.156 10 false *5 3.146,3.854 3.458,4.01 0.313,0.156 10 false *6 5.26,4 5.573,4.156 0.313,0.156 10 false *7 6.5,2.969 6.813,3.125 0.313,0.156 10 false *8 6.51,3.74 6.823,3.896 0.313,0.156 10 false *9
*1 Rear Planetary Gear *2 Front Planetary Gear
*3 Counter Drive Gear *4 Intermediate Shaft
*5 Input Shaft *6 U/D Planetary Gear
*7 Counter Driven Gear *8 Differential Drive Pinion
*9 Ring Gear - -



vi.

Reverse Gear (Shift Lever in R)

X136159C01
1.521,2.573 1.833,2.573 1.833,2.573 2.021,2.167 true 6.438,1.813 6.76,1.813 true 6.208,3.052 6.531,3.052 true 6.229,3.875 6.552,3.875 true 3.354,1.333 3.688,0.938 3.688,0.938 3.948,0.938 true 4.677,1.208 5,0.583 5,0.583 5.26,0.583 true 5.354,1.875 5.542,2.302 5.542,2.302 5.802,2.302 true 2.594,3.49 2.781,3.917 2.781,3.917 3.042,3.917 true 4.667,3.635 4.854,4.063 4.854,4.063 5.115,4.063 true 1.302,2.479 1.615,2.635 0.313,0.156 10 false *1 3.969,0.844 4.281,1 0.313,0.156 10 false *2 5.292,0.51 5.604,0.667 0.313,0.156 10 false *3 5.844,2.229 6.156,2.385 0.313,0.156 10 false *4 6.802,1.719 7.115,1.875 0.313,0.156 10 false *5 3.083,3.833 3.396,3.99 0.313,0.156 10 false *6 5.167,3.979 5.479,4.135 0.313,0.156 10 false *7 6.583,2.979 6.896,3.135 0.313,0.156 10 false *8 6.583,3.792 6.896,3.948 0.313,0.156 10 false *9
*1 Rear Planetary Gear *2 Front Planetary Gear
*3 Counter Drive Gear *4 Intermediate Shaft
*5 Input Shaft *6 U/D Planetary Gear
*7 Counter Driven Gear *8 Differential Drive Pinion
*9 Ring Gear - -





FAIL-SAFE


a.

This function minimizes the loss of operability when any abnormality occurs in each sensor or solenoid.

Fail-safe Control List
Malfunction Part Function
Speed Sensor During a speed sensor malfunction, the vehicle speed is detected through the signals from the counter gear speed sensor to effect normal control.
ATF Temperature Sensor During an ATF temperature sensor malfunction, the 4th upshift is prohibited.
Counter Gear Speed Sensor During a counter gear speed sensor malfunction, the 4th upshift is prohibited.
Solenoid Valve DSL When the solenoid valve DSL has a malfunction, the current to the solenoid valve is stopped. This stops lock-up control, then fuel economy decreases.
Solenoid Valves SL1, SL2,and S4 The current to the failed solenoid valve is cut off and control is effected by operating the other solenoid valves with normal operation. Shift control is effected as described in the table below, depending on the failed solenoid.

i.

When all solenoid valves are normal

Solenoid Valve Gear
SL1 SL2 S4
ON ON OFF 1st
OFF ON OFF 2nd
OFF OFF OFF 3rd
OFF OFF ON 4th


ii.

When solenoid valve SL1 is abnormal

Traveling in 1st or 2nd Gear
Solenoid Valve
SL1 SL2 S4

*: The 2nd brake (B1) is constantly operating.

X* ON OFF 2nd
X* ON OFF 2nd
X* OFF→ON OFF→ON 3rd
X* OFF→ON ON 3rd

Traveling 3rd or 4th Gear
Solenoid Valve
SL1 SL2 S4
X ON→OFF OFF 3rd
X ON→OFF OFF 3rd
X OFF ON 3rd
X OFF ON 4th


iii.

When solenoid valve SL2 is abnormal

Solenoid Valve Gear
SL1 SL2 S4
ON→OFF X OFF 3rd
OFF X OFF 3rd
OFF X OFF 3rd
OFF X ON 4th


iv.

When solenoid valve S4 is abnormal

Solenoid Valve Gear
SL1 SL2 S4
ON ON X 1st
OFF ON X 2nd
OFF OFF X 3rd
OFF OFF X 3rd


v.

When solenoid valves SL1 and SL2 are abnormal

Solenoid Valve Gear
SL1 SL2 S4
X X OFF 3rd
X X OFF 3rd
X X OFF 3rd
X X ON 4th


vi.

When solenoid valves SL1 and S4 are abnormal

Traveling in 1st or 2nd Gear
Solenoid Valve
SL1 SL2 S4
X ON X 2nd
X ON X 2nd
X OFF→ON X 2nd
X OFF→ON X 2nd

Traveling in 3rd or 4th Gear
Solenoid Valve
SL1 SL2 S4
X ON→OFF X 3rd
X ON→OFF X 3rd
X OFF X 3rd
X OFF X 3rd


vii.

When solenoid valves SL2 and S4 are abnormal

Solenoid Valve Gear
SL1 SL2 S4
ON→OFF X X 3rd
OFF X X 3rd
OFF X X 3rd
OFF X X 3rd


viii.

When solenoid valves SL1, SL2 and S4 are abnormal

Solenoid Valve Gear
SL1 SL2 S4
X X X 3rd
X X X 3rd
X X X 3rd
X X X 3rd




DIAGNOSIS


a.

When the engine ECU detects a malfunction, the engine ECU makes a diagnosis and memorizes the failed section. Furthermore, the check engine warning light in the combination meter illuminates or blinks to inform the driver.


b.

At the same time, the DTCs (Diagnosis Trouble Codes) are stored in memory. The DTCs can be read by connecting an intelligent tester II. For details, see the PREVIA/ TARAGO Repair Manual.