Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › from 2016.05
NM24M0E _56 Audio / Visual / Telematics _061578 PARK ASSIST / MONITORING _0300417 TOYOTA PARKING ASSIST-SENSOR SYSTEM UN GENERAL/CONTROL/DETAILS F

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


LHD Models
Component Function
Ultrasonic Sensor Detects and calculates the distance between the vehicle and the obstacle.
Clearance Sonar Switch Turns the front and rear clearance sonar system ON.
Clearance Sonar Buzzer Emits an intermittent sound to inform the driver that the clearance sonar ECU has detected an obstacle within the prescribed range.
Clearance Sonar ECU Judges the approximate distance between the vehicle and obstacle based on the signals from the ultrasonic sensors and sends the indicator signal to the indicator and the buzzer signal to the buzzer. Additionally, the clearance sonar ECU has a buzzer sound volume adjusting knob.
Clearance Sonar Indicator Displays the location of the obstacle and the approximate distance between the vehicle and the obstacle.

RHD Models
Component Function
Ultrasonic Sensor (6) Detects the distance between the vehicle and an obstacle.
Combination Meter TOYOTA Parking Assist-sensor System Indicator Illuminates to inform the driver when the system operation conditions are met.
Multi-information Display
·

Displays the location of the obstacle and the approximate distance between the vehicle and the obstacle.

·

Displays an indication of a malfunction or freezing of an ultrasonic sensor to inform the driver.


Master Warning Light Illuminates in accordance with the indication on the multi-information display.
Combination Meter Sends the vehicle speed signal to the clearance sonar ECU.
Clearance Sonar Switch Operating this switch allows the operation of the TOYOTA parking assist-sensor system to be enabled or disabled.
Clearance Sonar Buzzer Emits an intermittent sound to inform the driver that the clearance sonar ECU has detected an obstacle within the prescribed range.
Clearance Sonar ECU
·

Judges the approximate distance between the vehicle and an obstacle based on signals from the ultrasonic sensors. Output signals are sent to the multi-information display.

·

Sounds the clearance sonar buzzer.


Air Conditioner ECU Sends outside temperature information to the clearance sonar ECU to adjust the distance rate from the ultrasonic sensors.
Main Body ECU Sends model destination (information to indicate the market the vehicle was built for) to the clearance sonar ECU.
Neutral Start Switch Sends the shift position signals to the ECM.
ECM Transmits the shift position signals to the clearance sonar ECU.


SYSTEM CONTROL


a.

Detection Activation

i.

This system activates when the power source mode is IG-ON, the clearance sonar switch is turned ON, and the conditions shown below have been met.

Sensor Shift Position
P R Other than P or R

○: Detection

Front Corner Sensor - ○ ○
Rear Corner Sensor - ○ -
Back Sensor - ○ -



b.

Detection Range

Y209904


c.

Initial Check (Self-diagnosis)

i.

After the Toyota parking assist system has been activated, it illuminates the indicator light and sounds the buzzer for about 1 second, while checking for any malfunction in the ultrasonic sensors. If the system cannot activate its detection function due to a malfunction in an ultrasonic sensor, it alerts the driver of the malfunction by the indicator light for the malfunctioning area and the buzzer in synchronization with the flashing light. For details, refer to the Repair Manual.




CONSTRUCTION


a.

Ultrasonic Sensor

i.

The ultrasonic sensors are provided with a distance calculation function in order to digitalize the signals between the clearance sonar ECU and the ultrasonic sensor. As a result, the number of wiring harnesses has been reduced.


ii.

The following numbers of ultrasonic sensors are provided: 2 along the front corners, 2 along the rear corners, and 2 on the back centers. The ultrasonic sensors consist of a microphone that transmits and receives ultrasonic waves. The distance calculation circuit calculates the distance between the vehicle and the obstacle based on the received ultrasonic waves. The ultrasonic sensors transmit the calculated distance signals to the clearance sonar ECU.

Y210054C01
2.792,1.333 2.635,1.333 2.635,1.333 2.281,0.917 true 6.146,1.333 5.99,1.333 5.99,1.333 5.635,0.917 true 2.833,1.229 3.146,1.385 0.313,0.156 10 false *a 6.188,1.229 6.5,1.385 0.313,0.156 10 false *a 0.396,0.344 1.188,0.583 0.792,0.24 10 false *1, *2 (*B) 3.729,0.375 4.521,0.615 0.792,0.24 10 false *2 (*A), *3
*A Except AERAS Grade *B AERAS Grade
*1 Rear Corner Sensor *2 Front Corner Sensor
*3 Back Sensor - -
*a Microphone - -




b.

Clearance Sonar Buzzer

i.

The buzzer is installed in the heater control panel.



c.

Clearance Sonar Indicator and Clearance Sonar Switch (LHD Models)

i.

A switch that turns the power of this system ON/OFF, an obstacle detection display, and a buzzer are provided in the heater control panel.

Y209905C01
4.385,1.542 4.656,1.969 4.656,1.969 4.813,1.969 true 0.594,2.083 0.698,2.083 0.698,2.083 0.875,2.385 true 1.885,2.375 2.021,2.094 2.021,2.094 2.146,2.094 true 0.563,4.583 0.667,4.583 0.667,4.583 0.875,4.323 true 1.885,4.323 2.01,4.594 2.01,4.594 2.135,4.594 true 1.406,4.49 1.406,4.656 1.406,4.656 1.531,4.656 true 4.844,1.885 5.156,2.042 0.313,0.156 10 false *1 2.823,0.51 3.135,0.667 0.313,0.156 10 false *a 0.427,1.99 0.74,2.146 0.313,0.156 10 false *b 2.198,2 2.51,2.156 0.313,0.156 10 false *c 0.385,4.49 0.698,4.646 0.313,0.156 10 false *d 1.573,4.552 1.885,4.708 0.313,0.156 10 false *e 2.177,4.51 2.49,4.667 0.313,0.156 10 false *f
*1 Clearance Sonar Switch - -
*a Illuminates all the power, back sonar, and clearance sonar indicator lights. *b Front Left Side
*c Front Right Side *d Rear Left Side
*e Back Sonar *f Rear Right Side




d.

Clearance Sonar ECU

i.

The clearance sonar ECU effects overall control of the system, including the switching of the transmission, reception of the ultrasonic sensor signals, processing the received wave signals, determining the presence of obstacles, actuating the warning indicators and buzzer, and detecting an open circuit in the sensors.


ii.

The sound volume of the clearance sonar buzzer can be adjusted at the clearance sonar ECU.

Y209906C01
3.49,1.51 3.813,0.542 3.813,0.542 3.979,0.542 true 4,0.458 4.313,0.615 0.313,0.156 10 false *a
*a Buzzer Sound Adjusting Knob - -





OPERATION


a.

Ultrasonic Sensor

i.

When the vehicle speed is 10 km/h (6.25 mph) or more.


ii.

The shift lever position for all sensors:

Sensor Shift Position
R Except R
Front Corner Sensor Detection Detection
Rear Corner Sensor Detection Prohibition
Back Sensor Detection Prohibition


iii.

When sensors are abnormal in open and freezing detection, and obstacle detection.



b.

Clearance Sonar Buzzer

i.

The ON/OFF times of the clearance sonar buzzer vary in accordance with the distance to the obstacle as shown in the following table:

Item Buzzer Sensor Detection Level Distance to Obstacle [cm (in.)] ON Time (ms) OFF Time (ms)
Front Corner Sensor 2.4 kHz 2nd Approx. 50 (19.7) to 37.5 (14.8) 150 +/- 15 150 +/- 15
3rd Approx. 37.5 (14.8) to 25 (9.8) 75 +/- 7.5 75 +/- 7.5
4th Approx. 25 (9.8) or less Continuous 0
Rear Corner Sensor 2nd Approx. 50 (19.7) to 37.5 (14.8) 150 +/- 15 150 +/- 15
3rd Approx. 37.5 (14.8) to 25 (9.8) 75 +/- 7.5 75 +/- 7.5
4th Approx. 25 (9.8) or less Continuous 0
Back 1st Approx. 150 (59.1) to 60 (23.6) 150 +/- 15 650 +/- 65
2nd Approx. 60 (23.6) to 45 (17.7) 150 +/- 15 150 +/- 15
3rd Approx. 45 (17.7) to 35 (13.8) 75 +/- 7.5 75 +/- 7.5
4th Approx. 35 (13.8) or less Continuous 0



c.

Attentive Information Conditions and Buzzer Beeping Pattern

i.

The ultrasonic sensors are grouped into front sensors: front corner sensors, and rear: rear corner sensors and back sensors.


ii.

The following table indicates the changes in buzzer beeping patterns depending on obstacle detection.


iii.

It also shows the pattern changes in regard to detection by both front and rear groups.

Back Sensor Detection Level Corner Sensor Detection Level
4th 3rd 2nd Non Detection

*1: A 1.5-second cycle, which comprises 0.65 seconds of an intermittent beep (ON/OFF) period and 0.85 seconds of a continuous beep period, is repeated.

*2: A 0.5-second cycle, which comprises 0.25 seconds of an intermittent beep (ON/OFF) period and 0.25 seconds of a continuous beep period, is repeated.

1st Pattern B*2 Pattern A*1 Pattern A*1 Continuous Beep
2nd Pattern A*1 0.15 sec. 0.15 sec. 0.15 sec.
3rd Pattern A*1 0.15 sec. 0.3 sec. 0.3 sec.
4th Pattern A*1 0.15 sec. 0.3 sec. 0.8 sec.
Non Detection Continuous Beep 0.15 sec. 0.3 sec. No Beep

Pattern A
Y209957E01
1.219,0.594 1.5,0.594 1.5,0.594 1.844,1.385 false 1.698,1.385 1.5,0.604 1.5,0.604 1.76,1.375 false 0.042,0.49 1.26,0.792 1.219,0.302 10 false 0.05 +/- 0.005 sec. 2.5,0.531 3.542,0.719 1.042,0.188 10 false 1.5 +/- 0.15 sec. 3.208,1.219 3.906,1.406 0.698,0.188 10 false 0.85 sec. 1.021,1.594 1.333,1.792 0.313,0.198 10 false ON 1.021,1.906 1.479,2.104 0.458,0.198 10 false OFF 0.25,1.667 0.948,2.042 0.698,0.375 10 false Beep Start from OFF 0.083,2.156 0.625,2.354 0.542,0.198 10 false Buzzer 1.021,2.333 1.333,2.531 0.313,0.198 10 false ON 1.021,2.656 1.479,2.854 0.458,0.198 10 false OFF 0.25,2.604 0.958,3 0.708,0.396 10 false Beep Start from ON 1.656,3.281 3,3.469 1.344,0.188 10 false Buzzer OFF 7 times

Pattern B
Y209958E01
3.615,1.427 4.063,1.094 4.063,1.094 4.219,1.094 false 2.042,0.76 2.24,0.76 2.24,0.76 2.708,1.427 false 2.396,1.427 2.24,0.76 2.24,0.76 2.563,1.427 false 2.688,0.604 3.75,0.781 1.063,0.177 10 false 0.5 +/- 0.05 sec. 0.844,0.635 2.104,0.854 1.26,0.219 10 false 0.05 +/- 0.005 sec. 4.26,1.01 4.917,1.208 0.656,0.198 10 false 0.25 sec. 1.594,1.625 1.906,1.823 0.313,0.198 10 false ON 1.594,1.958 1.948,2.156 0.354,0.198 10 false OFF 0.656,1.698 1.365,2.104 0.708,0.406 10 false Beep Start from OFF 1.583,2.302 1.896,2.5 0.313,0.198 10 false ON 1.583,2.646 1.938,2.844 0.354,0.198 10 false OFF 0.667,2.385 1.375,2.771 0.708,0.385 10 false Beep Start from ON 0.156,2.135 0.74,2.333 0.583,0.198 10 false Buzzer 2.281,3.26 3.594,3.458 1.313,0.198 10 false Buzzer OFF 3 times



d.

Multi-information Display (RHD Models)

i.

The location of an obstacle and the approximate distance between the vehicle and the obstacle are displayed by the multi-information display on RHD models.


ii.

The number of lines shown on the display changes based on the actual distance and flashes when the detection level is 4th.

Y210055C01
1.052,1.344 1.052,0.865 1.052,0.865 0.906,0.865 true 1.521,1.344 1.521,0.865 1.521,0.865 1.708,0.865 true 1.031,2.604 1.031,3.229 1.031,3.229 0.885,3.229 true 1.521,2.604 1.521,3.229 1.521,3.229 1.677,3.229 true 1.292,2.708 1.292,3.458 1.292,3.458 1.448,3.458 true 0.729,0.74 1.042,0.896 0.313,0.156 10 false *a 1.74,0.75 2.052,0.906 0.313,0.156 10 false *b 0.719,3.115 1.031,3.271 0.313,0.156 10 false *c 1.49,3.354 1.802,3.51 0.313,0.156 10 false *d 1.729,3.115 2.042,3.271 0.313,0.156 10 false *e 2.958,0.344 3.271,0.5 0.313,0.156 10 false *f 2.958,2.052 3.281,2.333 0.323,0.281 10 false *g 3.521,3.198 3.833,3.354 0.313,0.156 10 false *h 4.365,3.198 4.677,3.354 0.313,0.156 10 false *i 5.229,3.208 5.458,3.51 0.229,0.302 10 false *j 6.01,3.208 6.323,3.365 0.313,0.156 10 false *k 3.698,1.521 4.01,1.677 0.313,0.156 10 false *i 4.75,1.531 4.979,1.833 0.229,0.302 10 false *j 5.885,1.542 6.198,1.698 0.313,0.156 10 false *k
*a Front Corner LH *b Front Corner RH
*c Rear Corner LH *d Back
*e Rear Corner RH *f Detection Level of Corner Sensors
*g Detection Level of Back Sensors *h 1st
*i 2nd *j 3rd
*k 4th - -