Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM › from 2016.05
NM24M0E _59 Vehicle Exterior _061579 DOOR / HATCH _0300420 POWER BACK DOOR SYSTEM UN GENERAL/CONTROL/DETAILS F

DOOR / HATCH  POWER BACK DOOR SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


Component Function
Power Back Door Drive Unit Power Back Door Motor Opens and closes the back door when actuated by the power back door ECU.
Power Back Door ECU Controls the power back door system in accordance with the signals received from the switches, sensors and ECU.
Magnetic Clutch Transmits the rotation of the power back door motor to the driven gear.
Hall IC Detects the back door position and the opening and closing speed of the back door.
Back Door Lock Assembly Opener & Closer Motor Locks and unlocks the latch of the back door lock when actuated by the power back door ECU.
Back Door Courtesy Switch Detects whether the back door is opened or closed. This switch turns ON when the back door is opened or ajar and OFF when the back door is closed.
Neutral Position Switch Detects the initial (neutral) position of the driven gear of the opener & closer motor. The switch is ON when the back door lock operates to the open side, and OFF when it operates to the close side.
Full Latch Switch Detects the fully closed position of the latch, turns ON in the over latch condition.
Half Latch Switch Detects the ajar position of the latch, turns ON in the open latch condition.
Touch Sensor Detects if an object is jammed in the back door.
Power Back Door Buzzer When the power back door system starts to operate, the buzzer sounds to inform the driver that the system is operating. The buzzer also sounds if the operating conditions have not been met or if a jammed has been detected.
PWR DOOR OFF Switch
·

Setting this switch to OFF prohibits system operation.

·

This switch is also used in the power slide door system.

·

In case that this switch is OFF, it is possible to do the open/close operation of the back door manually as the magnetic clutch of the power back door motor is OFF.


Power Back Door Opener/Closer Switch The back door opens or closes when this switch is turned ON from inside of the vehicle.
Power Back Door Closer Switch The back door closes when this switch is turned ON from outside of the vehicle.
Transmitter The back door opens or closes when the power back door button on the transmitter is pressed outside of the vehicle.
Back Door Open Switch This switch releases the latch of the back door lock for manual opening of the back door. Pressing the back door open switch during operation of the power back door system enables switching to manual operation of the back door.
Main Body ECU The main body ECU transmits a back door lock/unlock control signal, vehicle speed signal, and a shift P signal to the power back door ECU via CAN. Also, it receives a hazard request signal from the power back door ECU via CAN, and operates the flasher relay.


SYSTEM CONTROL


a.

This system, which is controlled by the power back door ECU, operates when the conditions indicated below have been met.

Power Source Mode Operating Condition

*1: The state in which the switch is not pressed

*2: The power back door can be operated if it is open.

IG-ON The PWR DOOR OFF switch is ON*1.
The back door is unlocked*2.
Battery voltage is 10.5V or more.
The shift lever is in the P position.
The vehicle speed is 5 km/h (3 mph) or less
OFF The PWR DOOR OFF switch is ON*1.
The back door is unlocked*2.
Battery voltage is 10.5V or more.



FUNCTION


a.

This system performs the functions listed below.

Function Outline
Opener Function Upon receiving an ON signal from the power back door opener/closer switch or the power back door button on the transmitter with the back door closed, the power back door ECU actuates the opener & closer motor and the power back door motor in order to release the latch of the back door lock and open the back door.
Closer Function Upon receiving an ON signal from the power back door opener/closer switch, power back door closer switch with the back door open, or manually closing the back door to a predetermined position or the power back door button on the transmitter, the power back door ECU actuates the power back door motor and the opener & closer motor in order to close the back door and engage the latch of the back door lock.
Jam Protection Function Upon receiving the signals from a touch sensor and the Hall ICs of the power back door motor, the power back door ECU detects that an object is jammed in the back door, and reverses the movement of the power back door motor.
The power back door buzzer sounds for 0.1 seconds when a jammed object is detected.
Reverse Control Function During a power back door operation, if the power back door ECU detects an ON signal from the power back door opener/closer switch or the power back door button on the transmitter, the power back door ECU sounds the power back door buzzer for approximately 0.1 seconds and reverses the power back door motor in order to reverse the back door to a predetermined position.
Back Door Open/Close Speed Control Function In accordance with the signals received from the Hall ICs, the power back door ECU effects the following controls:
·

Reduces the closing speed from approximately 200 mm (7.9 in.) before the back door is fully closed, in order to reduce the jamming load.

·

Reduces the opening speed from approximately 80 mm (3.1 in.) before the back door is fully open, in order to reduce the shock that occurs when it is fully open.


Diagnosis If the power back door ECU detects a malfunction in the power back door system, the power back door ECU diagnoses the failed section and stores the DTC (Diagnostic Trouble Code) in the main body ECU via the CAN. For details, see Repair Manual.
Fail-safe
·

If the power back door ECU detects any of the malfunctions listed below during power back door operation, the power back door ECU stops the power back door motor and sounds the warning buzzer simultaneously, then turns OFF the magnetic clutch and stops the system.

-

Open circuit in the touch sensor

-

The power back door motor is operated continuously for 30 sec. or more.

-

Abnormal back door position signal (Hall IC signal)

-

Abnormality with position switches on back door lock assembly.


·

During a power back door operation, if the shift lever is shifted to a position other than P, the power back door ECU performs the aforementioned fail-safe operation.




b.

Opener Function

i.

The operation of the power back door opener function is described below.

1.

The power back door opener/closer switch or the power back door button on the transmitter is turned ON for 1 second or more with the back door closed.

2.

The buzzer continues to sound while the power back door button is being pressed. The hazard lights will flash twice simultaneously with the start of the operation.

3.

The opener & closer motor operates to unlock the latch.

4.

Through the state of the back door courtesy switch, the power back door ECU detects that the latch has been released, and actuates the power back door motor to start opening the back door.

5.

Through the state of the half latch switch, the power back door ECU detects that the back door is open, and reverses the opener & closer motor to its initial position.

6.

Through the state of the neutral position switch, the power back door ECU detects that the motor has reverted to its initial position. Then, it stops the opener & closer motor.

7.

Through the Hall ICs of the power back door motor, the power back door ECU detects the back door position, and stops the power back door motor just before the back door is in its full open position, and turns OFF the magnetic clutch.

LHD Models
Y209901E01
1.677,0.594 3.542,0.792 1.865,0.198 10 false Power Back Door Drive Unit 1.479,0.979 2.271,1.333 0.792,0.354 10 false Power Back Door Motor 1.344,1.594 2.417,1.802 1.073,0.208 10 false Magnetic Clutch 1.542,2.208 2.219,2.406 0.677,0.198 10 false 2 Hall ICs 3.146,1.854 3.938,2.229 0.792,0.375 10 false Power Back Door ECU 0.76,3.49 1.875,4.01 1.115,0.521 10 false Power Back Door Opener & Closer Switch 2.177,3.573 2.615,3.771 0.438,0.198 10 false Tuner 1.979,4.198 2.75,4.563 0.771,0.365 10 false Certification ECU 1.021,4.74 1.844,5.083 0.823,0.344 10 false PWR DOOR OFF Switch 3.177,5.052 3.885,5.448 0.708,0.396 10 false Main Body ECU 4.458,0.594 6.177,0.792 1.719,0.198 10 false Back Door Lock Assembly 4.76,0.979 5.823,1.354 1.063,0.375 10 false Opener & Closer Motor 4.656,1.604 5.917,1.948 1.26,0.344 10 false Back Door Courtesy Switch 4.75,2.219 5.917,2.406 1.167,0.188 10 false Half Latch Switch 4.792,2.813 5.813,3.156 1.021,0.344 10 false Neutral Position Switch 5.688,3.49 6.802,3.875 1.115,0.385 10 false Power Back Door Buzzer 4.948,4.979 5.927,5.188 0.979,0.208 10 false Flasher Relay 4.948,5.656 5.896,5.854 0.948,0.198 10 false Hazard Lights

RHD Models
Y210072E01
1.521,0.49 3.385,0.771 1.865,0.281 10 false Power Back Door Drive Unit 4.802,0.5 6.667,0.781 1.865,0.281 10 false Back Door Lock Assembly 0.906,0.979 2.031,1.438 1.125,0.458 10 false Power Back Door Motor 0.938,1.698 2.021,2.094 1.083,0.396 10 false Magnetic Clutch 1.177,2.438 2.26,2.833 1.083,0.396 10 false 2 Hall ICs 0.563,4.333 1.427,4.917 0.865,0.583 10 false PWR DOOR OFF Switch 1.906,4.083 2.448,4.469 0.542,0.385 10 false Tuner 1.74,4.906 2.51,5.552 0.771,0.646 10 false Certification ECU 3.104,2.25 3.938,2.729 0.833,0.479 10 false Power Back Door ECU 4.906,0.979 6.469,1.333 1.563,0.354 10 false Opener and Closer Motor 5.083,1.708 6.365,2.146 1.281,0.438 10 false Back Door Courtesy Switch 5.198,2.438 6.323,2.833 1.125,0.396 10 false Half Latch Switch 4.958,3.156 6.448,3.563 1.49,0.406 10 false Neutral Position Switch 5.76,4.052 6.604,4.479 0.844,0.427 10 false Power Back Door Buzzer 3.969,5.344 4.625,5.698 0.656,0.354 10 false HS-CAN 5.125,5.01 6.365,5.417 1.24,0.406 10 false Combination Meter 5.313,5.844 6.208,6.25 0.896,0.406 10 false Hazard Lights 3.198,5.854 3.969,6.5 0.771,0.646 10 false Main Body ECU 0.365,6.729 1.979,7.271 1.615,0.542 10 false Power Back Door Opener and Closer Switch




c.

Closer Function

i.

The operation of the power back door closer function is described below.

1.

The power back door opener/closer switch, the power back door closer switch, or the power back door button on the transmitter is turned ON for 1 second or more with the back door open, or the back door is manually closed to a predetermined position.

2.

The buzzer continues to sound while the power back door button is being pressed. The hazard lights will flash twice simultaneously with the start of the operation.

3.

The power back door ECU actuates the power back door motor to start closing the back door.

4.

Upon detecting that the latch is disengaged through the state of the half latch switch, the power back door ECU actuates the opener & closer motor to engage the latch.

5.

Upon detecting that the back door has closed through the state of the back door courtesy switch, the power back door ECU stops the magnetic clutch and the power back door motor.

6.

Upon detecting that the latch has been engaged through the state of the half latch switch (ON → OFF), the power back door ECU operates the opener & closer motor forward in order to fully close the power back door.

7.

If the power back door ECU detects that the half latch switch has been turned ON again after the back door has fully closed, it stops the opener & closer motor. Then, it operates the opener & closer motor in reverse in order to return the sector gear to its initial position, until the neutral position switch turns ON.

LHD Models
Y209902E01
1.833,0.469 3.563,0.656 1.729,0.188 10 false Power Back Door Drive Unit 4.448,0.49 6.177,0.688 1.729,0.198 10 false Back Door Lock Assembly 1.448,0.865 2.229,1.208 0.781,0.344 10 false Power Back Door Motor 1.323,1.479 2.375,1.677 1.052,0.198 10 false Magnetic Clutch 1.458,2.094 2.156,2.302 0.698,0.208 10 false 2 Hall ICs 3.135,2.208 3.927,2.625 0.792,0.417 10 false Power Back Door ECU 4.781,0.865 5.844,1.208 1.063,0.344 10 false Opener & Closer Motor 4.646,1.469 5.927,1.823 1.281,0.354 10 false Back Door Courtesy Switch 4.719,2.083 5.854,2.302 1.135,0.219 10 false Half Latch Switch 4.813,2.688 5.844,3.052 1.031,0.365 10 false Neutral Position Switch 0.719,2.771 2.323,3.156 1.604,0.385 10 false Power Back Door Opener/Closer Switch 5.646,4 6.76,4.375 1.115,0.375 10 false Power Back Door Buzzer 2.198,4.698 2.646,4.885 0.448,0.188 10 false Tuner 3.083,5.354 3.677,5.531 0.594,0.177 10 false HS-CAN 2,5.365 2.771,5.74 0.771,0.375 10 false Certification ECU 1.063,5.885 1.885,6.24 0.823,0.354 10 false PWR DOOR OFF Switch 3.406,6.229 4.115,6.615 0.708,0.385 10 false Main Body ECU 4.927,6.135 5.854,6.365 0.927,0.229 10 false Flasher Relay 4.948,6.792 5.906,6.99 0.958,0.198 10 false Hazard Lights 0.854,4.438 1.979,4.792 1.125,0.354 10 false Power Back Door Closer Switch

RHD Models
Y210073E01
1.531,0.635 3.396,0.875 1.865,0.24 10 false Power Back Door Drive Unit 4.885,0.625 6.75,0.865 1.865,0.24 10 false Back Door Lock Assembly 1.135,1.146 1.917,1.646 0.781,0.5 10 false Power Back Door Motor 0.99,1.896 2.083,2.385 1.094,0.49 10 false Magnetic Clutch 1.146,2.615 1.875,3.031 0.729,0.417 10 false 2 Hall ICs 3.115,2.729 3.896,3.229 0.781,0.5 10 false Power Back Door ECU 0.635,4.458 1.417,4.958 0.781,0.5 10 false PWR DOOR OFF Switch 0.5,5.479 1.635,5.927 1.135,0.448 10 false Power Back Door Closer Switch 1.875,5.906 2.604,6.323 0.729,0.417 10 false Tuner 1.688,6.75 2.469,7.25 0.781,0.5 10 false Certification ECU 5.063,1.167 6.271,1.625 1.208,0.458 10 false Opener and Closer Motor 5.083,1.896 6.406,2.354 1.323,0.458 10 false Back Door Courtesy Switch 5.156,2.646 6.292,3.063 1.135,0.417 10 false Half Latch Switch 4.958,3.365 6.448,3.781 1.49,0.417 10 false Neutral Position Switch 5.76,5 6.885,5.521 1.125,0.521 10 false Power Back Door Buzzer 5.052,6.854 6.344,7.25 1.292,0.396 10 false Combination Meter 5.073,7.656 6.365,8.052 1.292,0.396 10 false Hazard Lights 3.135,7.677 3.854,8.323 0.719,0.646 10 false Main Body ECU 4.042,7.177 4.771,7.594 0.729,0.417 10 false HS-CAN 0.365,8.552 1.969,9.125 1.604,0.573 10 false Power Back Door Opener and Closer Switch




d.

Jam Protection Function

i.

The power back door ECU determines the jamming of the back door upon receiving the signals from a touch sensor and the Hall ICs of the power back door motor.


ii.

The power back door ECU determines the back door movement amount and the back door opening/closing speed (back door foreign object jamming) from the pulse signals from the Hall IC of the power back door motor, and the back door position (back door movement direction) from the phase difference between the pulses from Hall IC 1 and Hall IC 2 of the power back door motor.


iii.

If a foreign object has been jammed during opening or closing of the power back door, the pulse width of the output signal from Hall IC of the back door motor changes. The power back door ECU judges this change in pulse width as jamming, reversing the power back door motor.


iv.

If jamming is detected again during this reversal operation, the power back door ECU again reverses the power back door motor. However, if jamming is detected during the second closing operation or more, the power back door ECU turns OFF the magnetic clutch of the power back door motor, then sounds the power back door buzzer and stops power back door system operation. After the system is stopped, power back door system operation is restored by fully closing the back door manually.


v.

If either of the touch sensors located on each side of the back door is compressed by a jammed foreign object while the back door is closing, the resistance of the sensor changes. The power back door ECU judges this resistance change as jamming, and reverses the power back door motor.

Judgment of Amount of Movement and Opening/Closing Speed
Y209942E03
0.042,1.031 1.063,1.427 1.021,0.396 10 false Hall IC 1 Output Signal 1.021,2.083 2.583,2.354 1.563,0.271 10 false Standard Pulse (Normal) 3.885,2.083 5.792,2.49 1.906,0.406 10 false When Power Back Door Motor Speed Changes (Jammed)

Judgment of Back Door Moving Direction
Y209943E01
0.25,0.771 1.292,1.167 1.042,0.396 10 false Hall IC 1 Output Signal 0.25,1.583 1.271,2.031 1.021,0.448 10 false Hall IC 2 Output Signal 1.583,2.333 2.698,2.542 1.115,0.208 10 false Back Door Open 4.51,2.333 5.656,2.542 1.146,0.208 10 false Back Door Close




CONSTRUCTION


a.

Power Back Door Drive Unit

i.

The power back door drive unit consists of a power back door motor assembly, gears, shaft, arm, cover, etc.


ii.

Rotation of the power back door motor moves the arm forward and back via the gears, link mechanism and slider mechanism. The back door is opened and closed by movement of this arm.

Y209824C01
1.76,0.458 1.896,0.458 1.896,0.458 2.406,1.219 true 2.563,1.24 3.844,3.177 3.844,3.177 3.979,3.177 true 0.813,5.417 0.948,5.417 0.948,5.417 1.156,4.969 true 1.906,4.063 2.042,4.063 2.042,4.063 2.135,4.365 true 2.708,4.281 2.844,4.281 2.844,4.281 2.927,4.552 true 3.969,5.313 4.031,5.583 4.031,5.583 4.167,5.583 true 3.375,5.594 3.51,5.594 3.51,5.594 3.594,5.396 true 4.646,4.396 4.802,4.104 4.802,4.104 4.938,4.104 true 3.552,4.76 3.635,4.313 3.635,4.313 3.771,4.313 true 5.719,4.969 5.917,4.542 5.917,4.542 6.052,4.542 true 1.594,0.365 1.906,0.521 0.313,0.156 10 false *1 4,3.073 4.313,3.229 0.313,0.156 10 false *a 1.729,3.958 2.042,4.115 0.313,0.156 10 false *b 3.219,5.5 3.531,5.656 0.313,0.156 10 false *c 3.802,4.208 4.115,4.365 0.313,0.156 10 false *d 4.958,4.01 5.271,4.167 0.313,0.156 10 false *e 0.646,5.323 0.958,5.479 0.313,0.156 10 false *a 4.177,5.49 4.49,5.646 0.313,0.156 10 false *c 2.542,4.177 2.854,4.333 0.313,0.156 10 false *c 6.073,4.448 6.385,4.604 0.313,0.156 10 false *f
*1 Power Back Door Drive Unit - -
*a Arm *b Case
*c Gear *d Shaft
*e Cover *f Power Back Door Motor Assembly




b.

Back Door Lock Assembly

i.

The back door lock assembly consists of 3 position detection switches (neutral position switch, half latch switch, and back door courtesy switch), sector gear, open lever, latch, and opener & closer motor.


ii.

The rotation of the opener & closer motor is transmitted to the close or open lever via the sector gear. The operation of the open or closer lever engages or releases the latch.


iii.

When this system does not operate due to a discharged battery or other malfunctions, the back door can be opened by directly operating the open lever in the back door lock assembly.

Y209835C01
1.885,1.198 2.031,1.198 2.031,1.198 2.781,1.854 true 2.104,1.698 2.25,1.698 2.25,1.698 2.885,1.969 true 3.313,1.75 4.396,1.75 true 2.094,2.073 2.979,2.073 true 3.333,2.01 4.292,2.156 4.292,2.156 4.427,2.156 true 3.313,2.208 4.292,2.563 4.292,2.563 4.417,2.563 true 2.094,2.552 3.167,2.552 true 4.229,1.156 4.5,0.875 4.5,0.875 4.625,0.875 true 1.719,1.104 2.031,1.26 0.313,0.156 10 false *a 1.938,1.604 2.25,1.76 0.313,0.156 10 false *b 1.938,1.979 2.25,2.135 0.313,0.156 10 false *c 1.938,2.458 2.25,2.615 0.313,0.156 10 false *d 4.438,2.458 4.75,2.615 0.313,0.156 10 false *e 4.438,2.063 4.75,2.219 0.313,0.156 10 false *f 4.417,1.646 4.635,1.865 0.219,0.219 10 false *g 4.656,0.792 4.969,0.948 0.313,0.156 10 false *h
*a Open Lever *b Sector Gear
*c Close Lever *d Latch
*e Half Latch Switch and Back Door Courtesy Switch *f Latch Lever
*g Neutral Position Switch *h Opener & Closer Motor




c.

Touch Sensor

i.

While the back door is moving in the closing direction, if one of the touch sensors (right or left) located on each side of the back door becomes compressed due to the jamming of a foreign object, the built-in pieces of conductive rubber contact each other, causing the resistance of the sensor to change and a current to flow. Accordingly, the power back door ECU determines that the back door has jammed.

Y209900C01
3.313,1.625 3.313,1.052 3.313,1.052 3.469,1.052 true 4.208,2.823 4.208,1.573 4.208,1.573 4.365,1.573 true 5.115,2.094 5.229,2.094 5.229,2.094 5.396,2.323 true 5.573,2.427 6.021,2.573 6.021,2.573 6.125,2.573 true 3.49,0.969 3.802,1.125 0.313,0.156 10 false *1 1.604,1.396 1.917,1.552 0.313,0.156 10 false *a 3.99,3.927 4.302,4.083 0.313,0.156 10 false *b 5.667,1 5.979,1.156 0.313,0.156 10 false *c 5.667,2.75 5.979,2.906 0.313,0.156 10 false *d 5.667,4.844 5.979,5 0.313,0.156 10 false *e 4.979,2.01 5.292,2.167 0.313,0.156 10 false *f 6.156,2.479 6.427,2.698 0.271,0.219 10 false *g 1.573,1.833 1.729,2.031 0.156,0.198 10 false A 2.094,2.146 2.25,2.344 0.156,0.198 10 false A 4.385,1.49 4.698,1.646 0.313,0.156 10 false *1
*1 Touch Sensor - -
*a Detection Area *b Back Door Close Direction
*c A - A Cross Section *d Touch Sensor (Normal)
*e Touch Sensor (Jammed) *f Core Wire
*g Conductive Rubber - -





OPERATION


a.

Back Door Lock Assembly

i.

Opener Operation

·

When the opener & closer motor rotates clockwise, the sector gear, which links the opener & closer motor via the gear, moves to the left. This makes the sector gear push the open lever to the left. As a result, the ratchet moves in the releasing direction to release the latch.

Y209781C01
1.271,1.979 1.417,1.979 1.417,1.979 2.042,2.885 true 4.875,1.167 5.208,0.865 5.208,0.865 5.344,0.865 true 3.719,4.958 4.052,4.656 4.052,4.656 4.188,4.656 true 1.969,5.292 2.115,5.292 2.115,5.292 2.896,5.521 true 2.75,6.646 2.896,6.646 2.896,6.646 3.115,6.354 true 4.167,6.26 4.365,6.031 4.365,6.031 4.5,6.031 true 1.115,1.896 1.375,2.083 0.26,0.188 10 false *a 5.365,0.781 5.677,0.938 0.313,0.156 10 false *b 1.792,5.208 2.104,5.365 0.313,0.156 10 false *c 2.573,6.573 2.885,6.729 0.313,0.156 10 false *d 4.521,5.938 4.833,6.094 0.313,0.156 10 false *e 4.208,4.563 4.469,4.75 0.26,0.188 10 false *a
*a Sector Gear *b Opener & Closer Motor
*c Open Lever *d Ratchet
*e Latch - -




ii.

Closer Operation

·

When the opener & closer motor rotates counterclockwise, the sector gear, which links the opener & closer motor via the gear, moves to the right. This makes the projection A, which is mounted on the closer lever that moves in conjunction with the sector gear, push the latch lever to the right. As a result, the latch moves in the engaging direction.

Y209783C01
1.219,1.792 1.333,1.792 1.333,1.792 2.292,2.625 true 4.865,1.146 5.094,0.938 5.094,0.938 5.208,0.938 true 4.115,5.094 4.448,4.833 4.448,4.833 4.563,4.833 true 3.677,5.385 4.438,5.719 4.438,5.719 4.552,5.719 true 4.104,6.375 4.458,6.604 4.458,6.604 4.573,6.604 true 2.583,6.188 2.698,6.188 2.698,6.188 3.125,5.583 true 2.563,5.375 3.344,5.375 true 1.063,1.698 1.375,1.854 0.313,0.156 10 false *a 5.25,0.854 5.563,1.01 0.313,0.156 10 false *b 2.406,5.281 2.719,5.438 0.313,0.156 10 false *c 2.406,6.094 2.719,6.25 0.313,0.156 10 false *d 4.604,6.5 4.917,6.656 0.313,0.156 10 false *e 4.604,5.656 4.917,5.813 0.313,0.156 10 false *f 4.583,4.75 4.896,4.906 0.313,0.156 10 false *a
*a Sector Gear *b Opener & Closer Motor
*c Projection A *d Close Lever
*e Latch *f Latch Lever