Home › General › INTRODUCTION › REPAIR INSTRUCTION › 2013.04–2016.05
RM24M0E _V1 General _059537 INTRODUCTION _0291663 REPAIR INSTRUCTION D

INTRODUCTION  REPAIR INSTRUCTION  CUSTOMIZE PARAMETERS  


NOTICE:
·

When the customer requests a change in a function, first make sure that the function can be customized.

·

Make a note of the current settings before customizing.

·

When troubleshooting a function, first make sure that the function is set to the default setting.



2AZ-FE PUSH-BUTTON START


Smart entry and start system
Display (Item) Default Contents Setting
Key Lo-Batt Wrn
(Warns when key battery becomes weak)
ON Function that warns driver that key's battery power is low ON / OFF
Ignition Area
(Entry ignition available area)
ALL Function to choose available area for key to start engine and cancel steering lock FRONT / ALL*

HINT:

*: "FRONT" means front and rear, and "ALL" means front, rear and back door.



KEY CANCEL (2AZ-FE PUSH-BUTTON START)


The key cancel operation disables the following functions:

·

Entry ignition

·

Key lock-in prevention function

·

Warning function


a.

The operation procedures are as follows:

Precondition:

Engine switch off, driver side door closed and unlocked

i.

Press the key's UNLOCK switch once.


ii.

Open the driver door within 5 seconds.


iii.

Within 5 seconds of completing the previous step, press the key's UNLOCK switch twice.


iv.

Repeat open → close twice for the driver door within 30 seconds, and open again.

(Driver door: Open → Close → Open → Close → Open)


v.

Within 5 seconds of completing the previous step, press the key's UNLOCK switch twice.


vi.

Repeat open → close once for the driver door within 30 seconds, and open again.

(Driver door: Open → Close → Open)


vii.

Close the driver door within 5 seconds.

When key cancel is activated, the wireless door lock buzzer sounds twice.

To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.




2GR-FE PUSH-BUTTON START


Smart entry and start system
Display (Item) Default Contents Setting
Key Lo-Batt Wrn
(Warns when key battery becomes weak)
ON Function that warns driver that key's battery power is low ON / OFF
Ignition Area
(Entry ignition available area)
ALL Function to choose available area for key to start engine and cancel steering lock FRONT / ALL*

HINT:

*: "FRONT" means front and rear, and "ALL" means front, rear and back door.



KEY CANCEL (2GR-FE PUSH-BUTTON START)


The key cancel operation disables the following functions:

·

Entry ignition

·

Key lock-in prevention function

·

Warning function


a.

The operation procedures are as follows:

Precondition:

Engine switch off, driver side door closed and unlocked

i.

Press the key's UNLOCK switch once.


ii.

Open the driver door within 5 seconds.


iii.

Within 5 seconds of completing the previous step, press the key's UNLOCK switch twice.


iv.

Repeat open → close twice for the driver door within 30 seconds, and open again.

(Driver door: Open → Close → Open → Close → Open)


v.

Within 5 seconds of completing the previous step, press the key's UNLOCK switch twice.


vi.

Repeat open → close once for the driver door within 30 seconds, and open again.

(Driver door: Open → Close → Open)


vii.

Close the driver door within 5 seconds.

When key cancel is activated, the wireless door lock buzzer sounds twice.

To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.




AIR CONDITIONING SYSTEM


a.

Customizing with the intelligent tester

Air conditioning system
Display (Item) Default Contents Setting
Set Temperature Shift Normal To control with shifted temperature against displayed temperature -2C / -1C / Normal / +1C / +2C
Evaporator Control Automatic Function to set evaporator control to AUTOMATIC position (AUTO) to save power, or to coldest position (MANUAL) to dehumidify air and to prevent windows from fogging up Automatic / Manual
Compressor Mode Automatic Function to automatically turn A/C ON by pressing AUTO button when blower is ON and A/C is OFF Automatic / Manual
Air Inlet Mode Automatic Function to shift from INLET mode to RECIRCULATION mode when A/C is turned on Automatic / Manual
Foot / DEF Auto Mode ON Function to automatically turn airflow from FOOT/DEF ON when AUTO MODE is ON ON / OFF
Foot / DEF Automatic Blow Up Function ON Function to automatically increase blower level when defroster is ON ON / OFF
Ambient Temperature Shift Normal To control with shifted temperature against displayed temperature -3C / -2C / -1C / Normal / +1C / +2C / +3C


b.

Customizing using the multi-display

i.

Turn the engine switch on (IG).


ii.

Enter the following menus: SETUP / Vehicle / Vehicle customization / Climate settings.


iii.

Select the setting by referring to the table below.

Air conditioning system
Display (Item) Default Contents Setting
Auto A/C mode On Function to automatically turn A/C ON by pressing AUTO button when blower is ON and A/C is OFF On or Off
Efficient ventilation mode On Function to shift from INLET mode to RECIRCULATION mode when A/C is turned on On or Off




THEFT DETERRENT SYSTEM


Theft deterrent system
Display (Item) Default Contents Setting
WARN BY HORN
(Warning by horn)
ON Function that allows vehicle horns and theft deterrent horn to be used as warning device. ON / OFF


LIGHTING SYSTEM


a.

Customizing with the intelligent tester

Illuminated Entry
Display (Item) Default Contents Setting
Lighting Time 15 s Changes illumination duration after door closure.
(It will quickly fade out in case of turning engine switch on (IG).
7.5 s / 15 s / 30 s
I/L when ACC OFF ON Illuminates light when engine switch turned on (ACC).
(Room light illuminated when room light switch in DOOR position)
ON / OFF
I/L ON W/Door Key Unlock ON Function to light up room light, when unlocking with door key cylinder/wireless transmitter.
(Room light illuminated when room light switch in DOOR position)
ON / OFF
Illumination System ON Illuminated entry function ON / OFF
Light Control ON Function to light up foot light when engine switch is on (IG) and shift position is not P. ON / OFF
Interior Light Control ON Function to light up room light, when the illuminated entry function is operating. ON / OFF

Light Control
Display (Item) Default Contents Setting
Response Time Normal Delay time Normal / Long
Sensitivity Normal Sensitivity adjustment Normal
Dark2
Dark1
Light1
Light2
Disp Ex ON Sen Normal Changes the ambient brightness level required to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock.* Normal
Dark2
Dark1
Light1
Light2
Disp Ex OFF Sen Normal Changes the ambient brightness level required to cancel the dimming of the lights such as the indicator lights of the combination meter, A/C indicator light and clock.* Normal
Dark2
Dark1
Light1
Light2

HINT:

Sensitivity adjustments are difficult to confirm. Check by driving the customer's vehicle.



b.

Customizing using the multi-display

i.

Turn the engine switch to on (IG).


ii.

Enter the following menus: SETUP / Vehicle / Vehicle customization / Light settings.


iii.

Select the setting by referring to the table below.

Light settings
Display (Item) Default Contents Setting
Sensitivity Normal Sensitivity adjustment Normal
Dark2
Dark1
Light1
Light2
Lighting Time 15 s Changes illumination duration after door closure.
(It will quickly fade out in case of turning engine switch on (IG).
7.5 s / 15 s / 30 s

HINT:

Sensitivity adjustments are difficult to confirm. Check by driving the customer's vehicle.





WIRELESS DOOR LOCK CONTROL SYSTEM


a.

Customizing with the intelligent tester

Wireless door lock control system
Display (Item) Default Contents Setting
Hazard Ans Back ON When wireless lock switch on transmitter pressed, all hazard warning lights illuminate once. When unlock switch pressed, all hazard warning lights illuminate twice ON / OFF
Wireless Oper ON ON /OFF of wireless door lock function ON / OFF
Auto Lock Delay 30 seconds Time until relocking after unlocking with wireless door lock function 60 seconds / 30 seconds
Open Door Warn ON If door not completely closed and transmitter LOCK switch pressed, this function makes buzzer sound for 5 seconds ON / OFF
Wirls Buzz Resp ON ON / OFF of wireless buzzer response function ON / OFF


b.

Customizing using the multi-display

i.

Turn the engine switch on (IG).


ii.

Enter the following menus: SETUP / Vehicle / Vehicle customization / Door Lock Settings.


iii.

Select the setting by referring to the table below.

Wireless door lock control system
Display (Item) Default Contents Setting
Lock/unlock feedback-lights On When wireless lock switch on transmitter pressed, all hazard warning lights illuminate once. When unlock switch pressed, all hazard warning lights illuminate twice On or Off




SMART ENTRY AND START SYSTEM (FOR DOOR LOCK)


Smart entry and start system
Display (Item) Default Contents Setting
Park Wait Time
(Waiting time to permit opening door after locking)
3.0 s Function that sets waiting time to permit opening door after door is locked with entry lock function 1.0 s / 2.0 s / 3.0 s / 5.5 s
Back Door Oper
(Back door opening operation when vehicle is locked)
LONG Function that makes back door lock, unlock switch operation available LONG / TWICE / OFF
Key Lo-Batt Wrn
(Warns when key battery becomes weak)
ON Function that warns driver that key's battery power is low ON / OFF
Ignition Area
(Entry ignition available area)
ALL Function to choose available area for key to start engine and cancel steering lock FRONT / ALL*

HINT:

*: "FRONT" means front and rear, and "ALL" means front, rear and back door.



METER / GAUGE SYSTEM


Combination meter
Display Default Function Setting
Seat-belt Warning Buzzer D/P ON Seat belt warning buzzer ON / OFF setting D/P ON: Driver and passenger buzzer ON
D ON: Driver buzzer ON
P ON: Passenger buzzer ON
D/P OFF: Driver and passenger buzzer OFF
Key Remind Sound Normal Key reminder warning buzzer sound setting Fast
Normal
Slow


POWER SLIDE DOOR SYSTEM


Power slide door system
Display Default Function Setting
PSD SW Operation 0.8 s Function to operate power slide door switch 0.8 s / 0.0 s
PSD Buzz in use ON Function to sound buzzer when power slide door in operation ON / OFF
Wireless PSD SW Operation 0.8 s Function to operate wireless power slide door switch 1 TIME / 2 TIMES / 0.8 s / OFF


POWER BACK DOOR SYSTEM


Power back door system
Display Default Function Setting
PBD SW Operation 0.8 s Function that turns power back door closer switch ON when switch is pushed once or held down for 0.8 sec. 0.8 s / ON
PBD Buzzer ON This function makes the power back door buzzer sound when power back door operating ON / OFF
Wirels PBD SW Operation 0.8 s Function that operates power back door when transmitter switch is pressed in specified way (1-press, 2-presses, 0.8 sec.- press or OFF) ON / 2 times / 0.8 s / OFF