When the customer requests a change in a function, first make sure that the function can be customized.
Make a note of the current settings before customizing.
When troubleshooting a function, first make sure that the function is set to the default setting.
2AZ-FE PUSH-BUTTON START
| Display (Item) | Default | Contents | Setting |
|---|---|---|---|
| Key Lo-Batt Wrn
(Warns when key battery becomes weak) |
ON | Function that warns driver that key's battery power is low | ON / OFF |
| Ignition Area
(Entry ignition available area) |
ALL | Function to choose available area for key to start engine and cancel steering lock | FRONT / ALL* |
*: "FRONT" means front and rear, and "ALL" means front, rear and back door.
KEY CANCEL (2AZ-FE PUSH-BUTTON START)
The key cancel operation disables the following functions:
Entry ignition
Key lock-in prevention function
Warning function
The operation procedures are as follows:
Precondition:
Engine switch off, driver side door closed and unlocked
Press the key's UNLOCK switch once.
Open the driver door within 5 seconds.
Within 5 seconds of completing the previous step, press the key's UNLOCK switch twice.
Repeat open → close twice for the driver door within 30 seconds, and open again.
(Driver door: Open → Close → Open → Close → Open)
Within 5 seconds of completing the previous step, press the key's UNLOCK switch twice.
Repeat open → close once for the driver door within 30 seconds, and open again.
(Driver door: Open → Close → Open)
Close the driver door within 5 seconds.
When key cancel is activated, the wireless door lock buzzer sounds twice.
To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.
2GR-FE PUSH-BUTTON START
| Display (Item) | Default | Contents | Setting |
|---|---|---|---|
| Key Lo-Batt Wrn
(Warns when key battery becomes weak) |
ON | Function that warns driver that key's battery power is low | ON / OFF |
| Ignition Area
(Entry ignition available area) |
ALL | Function to choose available area for key to start engine and cancel steering lock | FRONT / ALL* |
*: "FRONT" means front and rear, and "ALL" means front, rear and back door.
KEY CANCEL (2GR-FE PUSH-BUTTON START)
The key cancel operation disables the following functions:
Entry ignition
Key lock-in prevention function
Warning function
The operation procedures are as follows:
Precondition:
Engine switch off, driver side door closed and unlocked
Press the key's UNLOCK switch once.
Open the driver door within 5 seconds.
Within 5 seconds of completing the previous step, press the key's UNLOCK switch twice.
Repeat open → close twice for the driver door within 30 seconds, and open again.
(Driver door: Open → Close → Open → Close → Open)
Within 5 seconds of completing the previous step, press the key's UNLOCK switch twice.
Repeat open → close once for the driver door within 30 seconds, and open again.
(Driver door: Open → Close → Open)
Close the driver door within 5 seconds.
When key cancel is activated, the wireless door lock buzzer sounds twice.
To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.
AIR CONDITIONING SYSTEM
Customizing with the GTS
| Display (Item) | Default | Contents | Setting |
|---|---|---|---|
| Set Temperature Shift | Normal | To control with shifted temperature against displayed temperature | -2C / -1C / Normal / +1C / +2C |
| Evaporator Control | Automatic | Function to set evaporator control to AUTOMATIC position (AUTO) to save power, or to coldest position (MANUAL) to dehumidify air and to prevent windows from fogging up | Automatic / Manual |
| Compressor Mode | Automatic | Function to automatically turn A/C ON by pressing AUTO button when blower is ON and A/C is OFF | Automatic / Manual |
| Air Inlet Mode | Automatic | Function to shift from INLET mode to RECIRCULATION mode when A/C is turned on | Automatic / Manual |
| Foot / DEF Auto Mode | ON | Function to automatically turn airflow from FOOT/DEF ON when AUTO MODE is ON | ON / OFF |
| Foot / DEF Automatic Blow Up Function | ON | Function to automatically increase blower level when defroster is ON | ON / OFF |
| Ambient Temperature Shift | Normal | To control with shifted temperature against displayed temperature | -3C / -2C / -1C / Normal / +1C / +2C / +3C |
| Ion Generate Control*1 | ON | Function to generate ions is stopped when item is OFF | ON / OFF |
| Outside Air Mode Auto Switch Function*2 | ON | Function to automatically change the air inlet to FRESH mode when the vehicle is parked | ON / OFF |
*1: w/ Ion Generator Assembly
*2: except China, G. C. C. countries
Customizing using the multi-display
Turn the engine switch on (IG).
Enter the following menus: SETUP / Vehicle / Vehicle customization / Climate settings.
Select the setting by referring to the table below.
| Display (Item) | Default | Contents | Setting |
|---|---|---|---|
| Auto A/C mode | On | Function to automatically turn A/C ON by pressing AUTO button when blower is ON and A/C is OFF | On or Off |
| Efficient ventilation mode | On | Function to shift from INLET mode to RECIRCULATION mode when A/C is turned on | On or Off |
THEFT DETERRENT SYSTEM
| Display (Item) | Default | Contents | Setting |
|---|---|---|---|
| WARN BY HORN
(Warning by horn) |
ON | Function that allows vehicle horns and theft deterrent horn to be used as warning device. | ON / OFF |
LIGHTING SYSTEM (for LED Headlight)
Customizing with the GTS
| Display (Item) | Default | Contents | Setting |
|---|---|---|---|
| Lighting Time | 15 s | Changes illumination duration after door closure.
(It will quickly fade out in case of turning engine switch on (IG). |
7.5 s / 15 s / 30 s |
| I/L when ACC OFF | ON | Illuminates light when engine switch turned on (ACC).
(Room light illuminated when room light switch in DOOR position) |
ON / OFF |
| I/L ON W/Door Key Unlock | ON | Function to light up room light, when unlocking with door key cylinder/wireless transmitter.
(Room light illuminated when room light switch in DOOR position) |
ON / OFF |
| Illumination System | ON | Illuminated entry function | ON / OFF |
| Light Control | ON | Function to light up inside handle illumination lights when engine switch is on (IG) and shift position is not P. | ON / OFF |
| Interior Light Control | ON | Function to light up room light, when the illuminated entry function is operating. | ON / OFF |
| Display (Item) | Default | Contents | Setting |
|---|---|---|---|
| Response Time | Normal | Delay time | Normal / Long |
| Disp Ex ON Sen | Normal | Changes the ambient brightness level required to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock. | Normal
Dark2 Dark1 Light1 Light2 |
| Disp Ex OFF Sen | Normal | Changes the ambient brightness level required to cancel the dimming of the lights such as the indicator lights of the combination meter, A/C indicator light and clock. | Normal
Dark2 Dark1 Light1 Light2 |
| Sensitivity | Normal | Sensitivity adjustment | Normal
Dark2 Dark1 Light1 Light2 |
| Daylight Function | ON | ON/OFF of the Daytime light function | ON / OFF |
The sensitivity adjustment may be difficult to confirm. Check by driving the vehicle.
Customizing using the multi-display
Turn the engine switch to on (IG).
Enter the following menus: SETUP / Vehicle / Vehicle customization / Light settings.
Select the setting by referring to the table below.
| Display (Item) | Default | Contents | Setting |
|---|---|---|---|
| Sensitivity | Normal | Sensitivity adjustment | Normal
Dark2 Dark1 Light1 Light2 |
| Lighting Time | 15 s | Changes illumination duration after door closure.
(It will quickly fade out in case of turning engine switch on (IG). |
7.5 s / 15 s / 30 s |
Sensitivity adjustments are difficult to confirm. Check by driving the customer's vehicle.
LIGHTING SYSTEM (except LED Headlight)
Customizing with the intelligent tester
| Display (Item) | Default | Contents | Setting |
|---|---|---|---|
| Lighting Time | 15 s | Changes illumination duration after door closure.
(It will quickly fade out in case of turning engine switch on (IG). |
7.5 s / 15 s / 30 s |
| I/L when ACC OFF | ON | Illuminates light when engine switch turned on (ACC).
(Room light illuminated when room light switch in DOOR position) |
ON / OFF |
| I/L ON W/Door Key Unlock | ON | Function to light up room light, when unlocking with door key cylinder/wireless transmitter.
(Room light illuminated when room light switch in DOOR position) |
ON / OFF |
| Illumination System | ON | Illuminated entry function | ON / OFF |
| Light Control | ON | Function to light up foot light when engine switch is on (IG) and shift position is not P. | ON / OFF |
| Interior Light Control | ON | Function to light up room light, when the illuminated entry function is operating. | ON / OFF |
| Display (Item) | Default | Contents | Setting |
|---|---|---|---|
| Response Time | Normal | Delay time | Normal / Long |
| Sensitivity | Normal | Sensitivity adjustment | Normal
Dark2 Dark1 Light1 Light2 |
| Disp Ex ON Sen | Normal | Changes the ambient brightness level required to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock. | Normal
Dark2 Dark1 Light1 Light2 |
| Disp Ex OFF Sen | Normal | Changes the ambient brightness level required to cancel the dimming of the lights such as the indicator lights of the combination meter, A/C indicator light and clock. | Normal
Dark2 Dark1 Light1 Light2 |
Sensitivity adjustments are difficult to confirm. Check by driving the customer's vehicle.
Customizing using the multi-display
Turn the engine switch to on (IG).
Enter the following menus: SETUP / Vehicle / Vehicle customization / Light settings.
Select the setting by referring to the table below.
| Display (Item) | Default | Contents | Setting |
|---|---|---|---|
| Sensitivity | Normal | Sensitivity adjustment | Normal
Dark2 Dark1 Light1 Light2 |
| Lighting Time | 15 s | Changes illumination duration after door closure.
(It will quickly fade out in case of turning engine switch on (IG). |
7.5 s / 15 s / 30 s |
Sensitivity adjustments are difficult to confirm. Check by driving the customer's vehicle.
WIRELESS DOOR LOCK CONTROL SYSTEM
Customizing with the GTS
| Display (Item) | Default | Contents | Setting |
|---|---|---|---|
| Hazard Answer Back | ON | When wireless lock switch on transmitter pressed, all hazard warning lights illuminate once. When unlock switch pressed, all hazard warning lights illuminate twice | ON / OFF |
| Wireless Control | ON | ON /OFF of wireless door lock function | ON / OFF |
| Auto Lock Time | 30 seconds | Time until relocking after unlocking with wireless door lock function | 60 seconds / 30 seconds |
| Open Door Warning | ON | If door not completely closed and transmitter LOCK switch pressed, this function makes buzzer sound for 5 seconds | ON / OFF |
| Wireless Buzzer Resp* | ON | ON / OFF of wireless buzzer response function | ON / OFF |
*: w/ Wireless Door Lock Buzzer Answer-back Function
Customizing using the multi-display
Turn the engine switch on (IG).
Enter the following menus: SETUP / Vehicle / Vehicle customization / Door Lock Settings.
Select the setting by referring to the table below.
| Display (Item) | Default | Contents | Setting |
|---|---|---|---|
| Lock/unlock feedback-lights | On | When wireless lock switch on transmitter pressed, all hazard warning lights illuminate once. When unlock switch pressed, all hazard warning lights illuminate twice | On or Off |
SMART ENTRY AND START SYSTEM (FOR DOOR LOCK)
| Display (Item) | Default | Contents | Setting |
|---|---|---|---|
| Park Wait Time
(Waiting time to permit opening door after locking) |
3.0 s | Function that sets waiting time to permit opening door after door is locked with entry lock function | 1.0 s / 2.0 s / 3.0 s / 5.5 s |
| Back Door Oper
(Back door opening operation when vehicle is locked) |
LONG | Function that makes back door lock, unlock switch operation available | LONG / TWICE / OFF |
| Key Lo-Batt Wrn
(Warns when key battery becomes weak) |
ON | Function that warns driver that key's battery power is low | ON / OFF |
| Ignition Area
(Entry ignition available area) |
ALL | Function to choose available area for key to start engine and cancel steering lock | FRONT / ALL* |
*: "FRONT" means front and rear, and "ALL" means front, rear and back door.
POWER WINDOW CONTROL SYSTEM
| Tester Display | Default | Content | Setting |
|---|---|---|---|
| Door Key P/W Up | OFF | Function to close the power windows using the mechanical key | OFF / ON |
| Door Key P/W Down | OFF | Function to open the power windows using the mechanical key | OFF / ON |
| P/W Up W/ Transmit | OFF | Function to close the power windows using the electrical key transmitter sub-assembly | OFF / ON |
| P/W Down W/ Transmit | OFF | Function to open the power windows using the electrical key transmitter sub-assembly | OFF / ON |
| P/W Up w/ Smart* | OFF | Function that raises all power windows when, with power switch off, entry lock switch on driver door outer handle is pressed and held for more than 3.0 seconds. | OFF / ON |
*: w/ Entry Lock Switch-linked Close Function
METER / GAUGE SYSTEM
| Display (Item) | Default | Function | Setting |
|---|---|---|---|
| Key Remind Sound | Slow | Key reminder warning buzzer sound setting | Fast
Normal Slow |
| Driver Side Seatbelt Warning Buzzer*1 | ON | Driver side seat belt warning buzzer ON / OFF setting | ON
OFF |
| Front Passenger Side Seatbelt Warning Buzzer*1 | ON | Front passenger side seat belt warning buzzer ON / OFF setting | ON
OFF |
| Seat-belt Warning Buzzer*2 | D/P ON | Seat belt warning buzzer ON / OFF setting | D/P ON: Driver side and front passenger side seat belt warning buzzer ON
D ON: Driver side seat belt warning buzzer ON P ON: Front passenger side seat belt warning buzzer ON D/P OFF: Driver side and front passenger side seat belt warning buzzer OFF |
| Display (Item) | Default | Function | Setting |
|---|---|---|---|
| ODO Display Time After IG OFF Setting*1 | 30s | Change the odometer display time after the ignition switch is turned off | 600s
60s 30s OFF |
*1: w/ Multi-information Display
*2: w/o Multi-information Display
TOYOTA PARKING ASSIST-SENSOR SYSTEM (for RHD)
| Display | Default | Content | Setting |
|---|---|---|---|
| Rr Sensor Onset Range | Wide | Sets the buzzer activation range for the rear center sensors. | Narrow or Wide
·
Narrow: 600 mm (23.6 in.) ·
Wide: 1500 mm (59.1 in.) |
| Keep Sense Buzzer | Avail | Sounds the buzzer when the distance between the vehicle and an obstacle does not change for more than 3 seconds. | Not Avail or Avail
·
Not Avail: Not Available ·
Avail: Available |
| Fr & Rr Buzzer Volume | H | Changes the buzzer volume setting. | L, M1, M2, M3 or H
·
L: Low volume ·
M1: Medium low volume ·
M2: Medium volume ·
M3: Medium high volume ·
H: High volume |
| Temporary Mute Reset Speed Adjust* | 20 km/h | Sets the vehicle speed at which the temporary mute function resets. | System Link,15 km/h, 20 m/h or 30 km/h
·
System Link: System Link ·
15 km/h: 15 km/h (9 mph) ·
20 km/h: 20 km/h (12 mph) ·
30 km/h: 30 km/h (19 mph) |
| Temporary Mute Function* | ON | Sets the availability of the temporary mute function. | ON or OFF
·
ON: Temporary Mute Function operating ·
OFF: Temporary Mute Function not operating |
*: Not applicable
| Display | Default | Content | Setting |
|---|---|---|---|
| Sensor Condition N | Avail | Makes the front sensors available when the shift lever is in N. | Not Avail or Avail
·
Not Avail: Not Available ·
Avail: Available |
| Reverse Range Front Sensor | F | Changes the operation setting for the front sensors when the shift lever is in R. | F or F Stop
·
F: Front sensors are available ·
F Stop: Front sensors are not available |
| Non P/R Range Rear Sensor | R Stop | Changes the operation setting for the rear sensors when the shift lever is in any position other than P or R. | R, Rcrn or R Stop
·
R: All rear sensors are available ·
Rcrn: Rear corner sensors are available ·
R Stop: All rear sensors are not available |
| Display | Default | Content | Setting |
|---|---|---|---|
| Display Mode* | All | The display mode setting (when the TOYOTA parking assist-sensor system is normal). | All or Undisp
·
All: Display displays all sensors ·
Undisp: Display does not display |
*: Not applicable
POWER SLIDE DOOR SYSTEM
| Display | Default | Function | Setting |
|---|---|---|---|
| PSD SW Operation | 0.8 s | Function to operate power slide door switch | 0.8 s / 0.0 s |
| PSD Buzz in use | ON | Function to sound buzzer when power slide door in operation | ON / OFF |
| Wireless PSD SW Operation | 0.8 s | Function to operate wireless power slide door switch | 1 TIME / 2 TIMES / 0.8 s / OFF |
POWER BACK DOOR SYSTEM
| Display | Default | Function | Setting |
|---|---|---|---|
| PBD SW Operation | 0.8 s | Function that turns power back door closer switch ON when switch is pushed once or held down for 0.8 sec. | 0.8 s / ON |
| PBD Buzzer | ON | This function makes the power back door buzzer sound when power back door operating | ON / OFF |
| Wirels PBD SW Operation | 0.8 s | Function that operates power back door when transmitter switch is pressed in specified way (1-press, 2-presses, 0.8 sec.- press or OFF) | ON / 2 times / 0.8 s / OFF |