| Part Tightened | N*m | kgf*cm | ft.*lbf |
|---|---|---|---|
| Front suspension member reinforcement RH x Front cross member, Front suspension crossmember | 96 | 979 | 71 |
| Part Tightened | N*m | kgf*cm | ft.*lbf |
|---|---|---|---|
| No. 1 camshaft bearing cap x Cylinder head | 29.5 | 301 | 22 |
| No. 2 camshaft bearing cap x Cylinder head | 29.5 | 301 | 22 |
| No. 3 camshaft bearing cap x Cylinder head | 9.0 | 92 | 80 in.*lbf |
| No. 1 chain tensioner x Timing chain cover | 9.0 | 92 | 80 in.*lbf |
| No. 2 camshaft x Camshaft timing sprocket | 54 | 551 | 40 |
| Part Tightened | N*m | kgf*cm | ft.*lbf | |
|---|---|---|---|---|
| Chain tensioner plate x Crankshaft bearing cap | 12 | 122 | 9 | |
| Oil pump drive shaft sprocket x Oil pump | 29.5 | 301 | 22 | |
| No. 1 chain vibration damper x Cylinder block | 9.0 | 92 | 80 in.*lbf | |
| Chain tensioner slipper x Cylinder head, Cylinder block | 19 | 194 | 14 | |
| Timing chain guide x Crankshaft bearing cap | 9.0 | 92 | 80 in.*lbf | |
| Timing chain cover x Cylinder head, Cylinder block | Bolt head size: 10 mm | 9.0 | 92 | 80 in.*lbf |
| Bolt head size: 12 mm | 25 | 255 | 18 | |
| Bolt head size: 14 mm | 55 | 561 | 41 | |
| Nut | 11 | 112 | 8 | |
| V-ribbed belt tensioner x Timing chain cover | 60 | 612 | 44 | |
| Engine mounting bracket RH x Timing chain cover | 55 | 561 | 41 | |
| Crankshaft pulley x Crankshaft | 180 | 1835 | 133 | |
| Oil pan x Stiffening crankcase | Bolt, Nut | 9.0 | 92 | 80 in.*lbf |
| Cylinder head cover x Cylinder head | Bolt A | 11 | 112 | 8 |
| Bolt B | 14 | 143 | 10 | |
| Nut | 11 | 112 | 8 | |
| Engine wire x Cylinder head cover | 8.4 | 86 | 74 in.*lbf | |
| Idler pulley x Cylinder block | 50 | 510 | 37 | |
| Engine hunger x Cylinder head | 38 | 387 | 28 | |
| Stud bolt x Cylinder block | 22 | 219 | 16 | |
| No. 1 chain tensioner x Timing chain cover | 9.0 | 92 | 80 in.*lbf | |
| Crankshaft position sensor x Timing chain cover | 9.0 | 92 | 80 in.*lbf | |
| Part Tightened | N*m | kgf*cm | ft.*lbf | |
|---|---|---|---|---|
| Camshaft position sensor x Cylinder head | 9.0 | 92 | 80 in.*lbf | |
| Oil pressure switch x Cylinder head | 15 | 153 | 11 | |
| Radio setting condenser x Cylinder head | 10 | 102 | 7 | |
| Cylinder head x Cylinder block | 1st | 78.5 | 800 | 58 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| Camshaft timing gear x Camshaft | 54 | 551 | 40 | |
| No. 2 camshaft timing sprocket x No. 2 camshaft | 54 | 551 | 40 | |
| No. 1 and No. 2 camshaft bearing cap x Cylinder head | 29.5 | 301 | 22 | |
| No. 3 camshaft bearing cap x Cylinder head | 9.0 | 92 | 80 in.*lbf | |
| Exhaust manifold x Cylinder head | 37 | 377 | 27 | |
| No. 1 exhaust manifold heat insulator x Exhaust manifold | 12 | 122 | 9 | |
| No. 1 and No. 2 manifold stay x Cylinder block, Exhaust manifold | 44 | 449 | 32 | |
| Oil dipstick guide x Cylinder block | 9.0 | 92 | 80 in.*lbf | |
| Stud bolt x Cylinder head | Front, Upper side | 9.5 | 97 | 84 in.*lbf |
| Part Tightened | N*m | kgf*cm | ft.*lbf | |
|---|---|---|---|---|
| Drive plate x Crankshaft | 98 | 1000 | 72 | |
| Drive shaft bearing bracket x Cylinder block | 64 | 653 | 47 | |
| No. 1 and No. 2 engine hanger x Cylinder head | 38 | 387 | 28 | |
| Engine mounting insulator LH x Body | 95 | 969 | 70 | |
| Engine mounting insulator LH | Through bolt | 56 | 571 | 41 |
| Engine mounting insulator RH x Body | 95 | 969 | 70 | |
| Engine mounting insulator RH x Engine mounting bracket | Nut A | 95 | 969 | 70 |
| Nut B | 52 | 530 | 38 | |
| Bolt | 95 | 969 | 70 | |
| Rear engine mounting insulator x Front suspension crossmember | Bolt and Nut | 95 | 969 | 70 |
| Rear engine mounting insulator x Engine mounting bracket | Though bolt | 95 | 969 | 70 |
| Front engine mounting insulator x Front cross member | 95 | 969 | 70 | |
| Front engine mounting insulator | Though bolt | 145 | 1479 | 107 |
| Front suspension crossmember x Body | 137 | 1397 | 101 | |
| Front suspension member brace x Body | Bolt A | 137 | 1397 | 101 |
| Bolt B | 93 | 948 | 69 | |
| Front crossmember x Body | 96 | 979 | 71 | |
| Steering intermediate shaft x Steering gear | 35 | 357 | 26 | |
| Radiator reservoir bracket x Engine mounting insulator sub-assembly RH | 5.5 | 56 | 49 in.*lbf | |
| Radiator reservoir x Radiator reservoir bracket | 5.5 | 56 | 49 in.*lbf | |
| Battery carrier support x Front battery carrier | 20 | 204 | 15 | |
| Battery carrier x Battery carrier support | 20 | 204 | 15 | |
| Battery clamp x Body | Bolt | 46 | 469 | 34 |
| Nut | 5.0 | 51 | 44 in.*lbf | |
| Front suspension member reinforcement LH and RH x Front cross member, Front suspension crossmember | 96 | 979 | 71 | |
| Hood x Hood hinge | 13 | 133 | 10 | |
| Part Tightened | N*m | kgf*cm | ft.*lbf | |
|---|---|---|---|---|
| Balance shaft housing x Stiffening crankcase | 1 st | 21.6 | 220 | 16 |
| 2 nd | Turn 90° | Turn 90° | Turn 90° | |
| Connecting rod cap x connecting rod | 1 st | 24.5 | 250 | 18 |
| 2 nd | Turn 90° | Turn 90° | Turn 90° | |
| Crankshaft bearing cap x Cylinder block | 1 st | 40 | 408 | 30 |
| 2 nd | Turn 90° | Turn 90° | Turn 90° | |
| Stud bolt x Cylinder block
for TMC Made Engine |
Bolt A and C | 5.0 | 51 | 44 in.*lbf |
| Bolt B | 9.5 | 97 | 84 in.*lbf | |
| Stud bolt x Cylinder block
for TMC Made Engine |
Bolt A | 5.0 | 51 | 44 in.*lbf |
| Bolt B | 9.5 | 97 | 84 in.*lbf | |
| No. 1 oil nozzle x Cylinder block | 7.0 | 71 | 62 in.*lbf | |
| Stiffening crankcase x Cylinder block | 24 | 245 | 18 | |
| Oil control valve filter x Cylinder block | 30 | 306 | 22 | |
| Cylinder block water drain cock x Cylinder block | 25 | 255 | 18 | |
| Camshaft timing oil control valve x Cylinder head | 9.0 | 92 | 80 in.*lbf | |
| Oil pan drain plug x Oil pan | 40 | 408 | 30 | |
| Oil filter union x Stiffening crankcase
(w/o Oil Cooler) |
30 | 306 | 22 | |
| Spark plug x Cylinder head | 19 | 194 | 14 | |
| Ventilation valve x Cylinder head cover | 19 | 194 | 14 | |
| No. 1 water by-pass pipe x Cylinder head | 9.0 | 92 | 80 in.*lbf | |
| Union bolt
(w/ Oil Cooler) |
25 | 255 | 18 | |
| Oil cooler pipe x Cylinder head | 9.0 | 92 | 80 in.*lbf | |
| Engine oil cooler x Stiffening crankcase
(w/ Oil Cooler) |
Oil filter union | 79 | 806 | 58 |
| Nut | 9.0 | 92 | 80 in.*lbf | |
| No. 1 taper screw plug x Cylinder block
(w/o Oil Cooler) |
26 | 265 | 19 | |