Home › General › SPECIFICATIONS › 2AZ-FE STARTING
RM24M0E _V1 General _059539 SPECIFICATIONS _0291731 2AZ-FE STARTING F

SPECIFICATIONS  2AZ-FE STARTING  SERVICE DATA  


for 1.6 kW Type
Starter assembly Standard current: 90 A or less at 11.5 V
Starter magnetic switch assembly Standard resistance
50 - C: Below 1 Ω
50 - Body: Below 2 Ω
Starter armature assembly Standard resistance
Segment: Below 1 Ω
Segment - Coil core: 10 kΩ or higher
Standard length: 3.1 to 3.8 mm (0.122 to 0.150 in.)
Starter commutator end frame Standard length: 4.0 to 9.0 mm (0.158 to 0.359 in.)
Standard resistance
Positive (+) - Negative (-): 10 kΩ or higher
Snap ring Maximum length: 5.0 mm (0.197 in.)
Starter relay 3 - 5: 10 kΩ or higher
3 - 5: Below 1 Ω (when battery voltage is applied to terminals 1 and 2)
Starter cut relay
(w/ Smart Entry and Start System)
3 - 5: 10 kΩ or higher
3 - 5: Below 1 Ω (when battery voltage is applied to terminals 1 and 2)
Ignition switch
(w/o Smart Entry and Start System)
LOCK: Between all terminals 10 kΩ or higher
ACC: 2 (AM1) - 3 (ACC) Below 1 Ω
ON: 2 (AM1) - 3 (ACC) Below 1 Ω
ON: 3 (ACC) - 4 (IG1) Below 1 Ω
ON: 6 (IG2) - 7 (AM2) Below 1 Ω
START: 1 (ST1) - 4 (IG1) Below 1 Ω
START: 2 (AM1) - 4 (IG1) Below 1 Ω
START: 6 (IG2) - 7 (AM2) Below 1 Ω
START: 6 (IG2) - 8 (ST2) Below 1 Ω
Engine switch
(w/ Smart Entry and Start System)
7 (SS1) - 5 (GND) / 2 (SS2) - 5 (GND)
Specified resistance
Not pushed: 10kΩ or higher
Pushed: 15 Ω
Standard condition: Illuminates
Measurement condition
Battery positive 11 (SWIL) - Battery negative 4 (COM) or 5 (GND)
Battery positive 12 (INDS) - Battery negative 4 (COM) or 5 (GND)
Battery positive 13 (INDW) - Battery negative 4 (COM) or 5 (GND)

for 1.7 kW Type
Starter assembly Standard current: 90 A or less at 11.5 V
Starter magnetic switch assembly Standard resistance
50 - C: Below 1 Ω
50 - Body: Below 2 Ω
Starter armature assembly Standard resistance
Segment: Below 1 Ω
Segment - Coil core: 10 kΩ or higher
Standard length: 3.1 to 3.8 mm (0.122 to 0.150 in.)
Starter commutator end frame Standard length: 4.0 to 9.0 mm (0.158 to 0.359 in.)
Standard resistance
Positive (+) - Negative (-): 10 kΩ or higher
Snap ring Maximum length: 5.0 mm (0.197 in.)
Starter relay 3 - 5: 10 kΩ or higher
3 - 5: Below 1 Ω (when battery voltage is applied to terminals 1 and 2)
Starter cut relay
(w/ Smart Entry and Start System)
3 - 5: 10 kΩ or higher
3 - 5: Below 1 Ω (when battery voltage is applied to terminals 1 and 2)
Ignition switch
(w/o Smart Entry and Start System)
LOCK: Between all terminals 10 kΩ or higher
ACC: 2 (AM1) - 3 (ACC) Below 1 Ω
ON: 2 (AM1) - 3 (ACC) Below 1 Ω
ON: 3 (ACC) - 4 (IG1) Below 1 Ω
ON: 6 (IG2) - 7 (AM2) Below 1 Ω
START: 1 (ST1) - 4 (IG1) Below 1 Ω
START: 2 (AM1) - 4 (IG1) Below 1 Ω
START: 6 (IG2) - 7 (AM2) Below 1 Ω
START: 6 (IG2) - 8 (ST2) Below 1 Ω
Engine switch
(w/ Smart Entry and Start System)
7 (SS1) - 5 (GND) / 2 (SS2) - 5 (GND)
Specified resistance
Not pushed: 10kΩ or higher
Pushed: 15 Ω
Standard condition: Illuminates
Measurement condition
Battery positive 11 (SWIL) - Battery negative 4 (COM) or 5 (GND)
Battery positive 12 (INDS) - Battery negative 4 (COM) or 5 (GND)
Battery positive 13 (INDW) - Battery negative 4 (COM) or 5 (GND)