Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0115  Engine Coolant Temperature Circuit Malfunction  P0117  Engine Coolant Temperature Circuit Low Input  P0118  Engine Coolant Temperature Circuit High Input  


DESCRIPTION

A thermistor, whose resistance value varies according to the engine coolant temperature, is built into the engine coolant temperature sensor. The structure of the sensor and its connection to the ECM are the same as those of the intake air temperature sensor.

HINT:

When DTC P0115, P0117 or P0118 is stored, the ECM enters fail-safe mode. During fail-safe mode, the engine coolant temperature is estimated to be 80°C (176°F) by the ECM. Fail-safe mode continues until a pass condition is detected.


DTC No. DTC Detection Condition Trouble Area
P0115 Open or short in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic)
·

Open or short in engine coolant temperature sensor circuit


·

Engine coolant temperature sensor


·

ECM


P0117 Short in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic)
·

Short in engine coolant temperature sensor circuit


·

Engine coolant temperature sensor


·

ECM


P0118 Open in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic)
·

Open in engine coolant temperature sensor circuit


·

Engine coolant temperature sensor


·

ECM



HINT:

When any of these DTCs are output, check the engine coolant temperature using the intelligent tester. Enter the following menus on the tester: Powertrain / Engine / Data List / All Data / Coolant Temp.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) Short circuit

WIRING DIAGRAM

A255126E40
0.215,2.726 0.501,2.874 0.287,0.147 10 D7 0.215,2.894 2.573,3.233 2.358,0.339 10 Engine Coolant Temperature Sensor 1.987,1.485 2.094,1.634 0.107,0.149 10 2 1.987,2.088 2.094,2.238 0.107,0.149 10 1 5.409,1.48 5.786,1.633 0.377,0.153 10 THW 5.144,1.484 5.394,1.630 0.249,0.146 10 79 5.144,2.088 5.394,2.234 0.249,0.146 10 78 5.409,2.088 5.907,2.242 0.498,0.153 10 ETHW 5.989,1.359 6.116,1.513 0.128,0.155 10 R 6.014,1.069 6.259,1.219 0.245,0.150 10 5 V 6.027,3.109 6.366,3.264 0.339,0.155 10 ECM 5.782,3.109 6.066,3.257 0.285,0.147 10 D1 1.57,1.496 1.947,1.649 0.377,0.153 10 THW 1.725,2.088 1.945,2.242 0.220,0.153 10 E2

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

·

If DTC P0117 is stored, check that the engine does not overheat (the DTC P0117 may be stored due to engine overheating).



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Coolant Temp.


e.

Read the value displayed on the tester.

Standard value:

Between 75 and 100°C (167 and 212°F) with warm engine.


Result
Result Proceed to
-40°C (-40°F) A
140°C (284°F) B
Between 75 and 100°C (167 and 212°F) C

HINT:
·

If there is an open circuit, the tester indicates -40°C (-40°F).

·

If there is a short circuit, the tester indicates 140°C (284°F).





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

4.CHECK ENGINE COOLANT TEMPERATURE SENSOR (CHECK FOR SHORT IN SENSOR)

C

CHECK FOR INTERMITTENT PROBLEMS

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.
U188251E02
0.302,0.521 1.104,0.719 0.802,0.198 10 false ECT Sensor 1.365,2.865 2.156,3.063 0.792,0.198 10 false ECT Sensor 2.302,3.646 3,3.844 0.698,0.198 10 false Front View 0.302,0.323 0.521,0.5 0.219,0.177 10 false D7 0.969,2.865 1.167,3.042 0.198,0.177 10 false D7 2.5,1.813 2.906,1.99 0.406,0.177 8 false ETHW 2.542,0.448 2.885,0.625 0.344,0.177 10 false ECM 2.51,1.323 2.844,1.479 0.333,0.156 8 false THW 0.125,2.177 1.427,2.333 1.302,0.156 10 false Wire Harness Side:

Disconnect the engine coolant temperature (ECT) sensor connector.


b.

Connect terminals 1 (E2) and 2 (THW) of the ECT sensor connector on the wire harness side.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.


g.

Read the value displayed on the tester.

Standard:

140°C (284°F).




OK

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the ECT sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance between the terminals.

Standard resistance:
Tester Connection Condition Specified Condition
D1-79 (THW) - D7-2 (THW) Always Below 1 Ω
D1-78 (ETHW) - D7-1 (E2) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ENGINE COOLANT TEMPERATURE SENSOR (CHECK FOR SHORT IN SENSOR)
a.
A242995E04
0.406,0.115 0.74,0.281 0.333,0.167 10 false D7 0.406,0.302 1.271,0.469 0.865,0.167 10 false ECT Sensor 2.521,0.177 2.875,0.344 0.354,0.167 10 false ECM 2.521,1.073 2.875,1.24 0.354,0.167 10 false THW 2.5,1.521 2.969,1.667 0.469,0.146 10 false ETHW

Disconnect the ECT sensor connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.


f.

Read the value displayed on the tester.

Standard:

-40°C (-40°F)




OK

NG

5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the ECT sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance between the terminals.

Standard resistance:
Tester Connection Condition Specified Condition
D1-79 (THW) or D7-2 (THW) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR