Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM U

2GR-FE ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


U188254E02
2.688,0.354 2.875,0.531 0.188,0.177 10 false D1 5.594,0.354 5.792,0.573 0.198,0.219 10 false A7

HINT:

The standard voltage between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals are also indicated.

The result of checks should be compared with the standard voltage for that pair of terminals, and displayed in the "Specified Condition" column.

The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A7-2 (+B) - D1-81 (E1) B - BR Power source of ECM Engine switch on (IG) 11 to 14 V
A7-1 (+B2) - D1-81 (E1) B - BR Power source of ECM Engine switch on (IG) 11 to 14 V
A7-20 (BATT) - D1-81 (E1) W - BR Battery (for measuring the battery voltage and for the ECM memory) Always 11 to 14 V
A7-3 (+BM) - D1-81 (E1) R - BR Power source of throttle actuator Always 11 to 14 V
A7-44 (MREL) - D1-81 (E1) Y - BR EFI MAIN relay operation signal Engine switch on (IG) 11 to 14 V
D1-96 (VCTA) - D1-97 (ETA) B - W Power source for throttle position sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
D1-115 (VCV1) - D1-81 (E1) G-R - BR Power source for VVT sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
D1-114 (VCE1) - D1-81 (E1) GR - BR Power source for VVT sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
D1-112 (VCE2) - D1-81 (E1) Y - BR Power source for VVT sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
D1-113 (VCV2) - D1-81 (E1) V - BR Power source for VVT sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
A7-28 (IGSW) - D1-81 (E1) BE - BR Engine switch signal Engine switch on (IG) 11 to 14 V
A7-7 (FC) - D1-81 (E1) L - BR C/OPN relay operation signal (fuel pump control) Engine switch on (IG) 11 to 14 V
Idling Below 1.5 V
A7-36 (STP) - D1-81 (E1) L - BR Stop light switch assembly signal Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V
A7-35 (ST1-) - D1-81 (E1) V - BR Stop light switch assembly signal (opposite to STP terminal) Engine switch on (IG), brake pedal depressed Below 1.5 V
Engine switch on (IG), brake pedal released 7.5 to 14 V
A7-13 (ACCR) - D1-81 (E1) GR - BR ACC relay control signal Cranking Below 1.5 V
A7-55 (VPA) - A7-59 (EPA) V - BR Accelerator pedal position sensor signal (for engine control) Engine switch on (IG), accelerator pedal fully released 0.5 to 1.1 V
Engine switch on (IG), accelerator pedal fully depressed 2.6 to 4.5 V
A7-56 (VPA2) - A7-60 (EPA2) Y - BE Accelerator pedal position sensor signal (for sensor malfunction detection) Engine switch on (IG), accelerator pedal fully released 1.2 to 2.0 V
Engine switch on (IG), accelerator pedal fully depressed 3.4 to 4.75 V
A7-27 (TC) - D1-81 (E1) R - BR Terminal TC of DLC3 Engine switch on (IG) 11 to 14 V
A7-57 (VCPA) - A7-59 (EPA) P - R Power source of accelerator pedal position sensor (for VPA) Engine switch on (IG) 4.5 to 5.5 V
A7-58 (VCP2) - A7-60 (EPA2) B - BE Power source of accelerator pedal position sensor (for VPA2) Engine switch on (IG) 4.5 to 5.5 V
A7-15 (TACH) - D1-81 (E1) B - BR Engine speed signal (for combination meter assembly) Idling Pulse generation
(see waveform 1)
A7-8 (SPD) - D1-81 (E1) B - BR Vehicle speed signal from combination meter assembly Driving at 20 km/h (12 mph) Pulse generation
(see waveform 2)
A7-24 (W) - D1-81 (E1) Y - BR Malfunction Indicator Lamp (MIL) operation signal Engine switch on (IG)
(MIL goes on)
Below 3.0 V
Idling with warm engine 11 to 14 V
A7-41 (CANH) - D1-81 (E1) B - BR CAN communication line Engine switch on (IG) Pulse generation
(see waveform 3)
D1-2 (CAN+) - D1-81 (E1) B - BR CAN communication line Engine switch on (IG) Pulse generation
(see waveform 3)
A7-49 (CANL) - D1-81 (E1) W - BR CAN communication line Engine switch on (IG) Pulse generation
(see waveform 4)
D1-1 (CAN-) - D1-81 (E1) W - BR CAN communication line Engine switch on (IG) Pulse generation
(see waveform 4)
D1-81 (E1) - Body ground BR - - Earth (ground) circuit of ECM Always Below 1 Ω
D1-45 (#10) - D1-22 (E01) Y - BR No. 1 fuel injector assembly signal Engine switch on (IG) 11 to 14 V
Idling Pulse generation
(see waveform 5)
D1-85 (#20) - D1-22 (E01) W - BR No. 2 fuel injector assembly signal Engine switch on (IG) 11 to 14 V
Idling Pulse generation
(see waveform 5)
D1-44 (#30) - D1-22 (E01) B - BR No. 3 fuel injector assembly signal Engine switch on (IG) 11 to 14 V
Idling Pulse generation
(see waveform 5)
D1-84 (#40) - D1-22 (E01) L - BR No. 4 fuel injector assembly signal Engine switch on (IG) 11 to 14 V
Idling Pulse generation
(see waveform 5)
D1-43 (#50) - D1-22 (E01) L - BR No. 5 fuel injector assembly signal Engine switch on (IG) 11 to 14 V
Idling Pulse generation
(see waveform 5)
D1-83 (#60) - D1-22 (E01) G - BR No. 6 fuel injector assembly signal Engine switch on (IG) 11 to 14 V
Idling Pulse generation
(see waveform 5)
A7-48 (STA) - D1-81 (E1) B - BR ST relay operation signal Cranking 11 to 14 V
A7-14 (STSW) - D1-81 (E1) P - BR Engine cranking required signal Cranking 9 to 14 V
D1-52 (OC2+) - D1-51 (OC2-) BR - B Camshaft timing oil control valve assembly (for intake camshaft of bank 2) operation signal Idling Pulse generation
(see waveform 6)
D1-58 (OC1+) - D1-57 (OC1-) W - B Camshaft timing oil control valve assembly (for intake camshaft of bank 1) operation signal Idling Pulse generation
(see waveform 6)
D1-67 (VV2+) - D1-90 (VV2-) W - B VVT sensor (for intake camshaft of bank 2) signal Idling Pulse generation
(see waveform 7)
D1-69 (VV1+) - D1-92 (VV1-) P - L-B VVT sensor (for intake camshaft of bank 1) signal Idling Pulse generation
(see waveform 7)
D1-110 (NE+) - D1-111 (NE-) G - R Crankshaft position sensor signal Idling Pulse generation
(see waveform 7, 8)
D1-66 (EV2+) - D1-89 (EV2-) R - L VVT sensor (for exhaust camshaft of bank 2) signal Idling Pulse generation
(see waveform 8)
D1-68 (EV1+) - D1-91 (EV1-) Y - G VVT sensor (for exhaust camshaft of bank 1) signal Idling Pulse generation
(see waveform 8)
D1-16 (OE1+) - D1-17 (OE1-) R - LG Camshaft timing oil control valve assembly (for exhaust camshaft of bank 1) operation signal Idling Pulse generation
(see waveform 9)
D1-14 (OE2+) - D1-15 (OE2-) W - B Camshaft timing oil control valve assembly (for exhaust camshaft of bank 2) operation signal Idling Pulse generation
(see waveform 9)
D1-19 (M+) - D1-20 (ME01) G - BR Throttle actuator operation signal (positive terminal) Idling with warm engine Pulse generation
(see waveform 10)
D1-18 (M-) - D1-20 (ME01) R - BR Throttle actuator operation signal (negative terminal) Idling with warm engine Pulse generation
(see waveform 11)
D1-21 (E02) - Body ground W-B - - Earth (ground) circuit of ECM Always Below 1 Ω
D1-22 (E01) - Body ground BR - - Earth (ground) circuit of ECM Always Below 1 Ω
D1-40 (IGT1) - D1-81 (E1) W - BR No. 1 ignition coil assembly (ignition signal) Idling Pulse generation
(see waveform 12)
D1-39 (IGT2) - D1-81 (E1) G-R - BR No. 2 ignition coil assembly (ignition signal) Idling Pulse generation
(see waveform 12)
D1-38 (IGT3) - D1-81 (E1) G - BR No. 3 ignition coil assembly (ignition signal) Idling Pulse generation
(see waveform 12)
D1-37 (IGT4) - D1-81 (E1) LG - BR No. 4 ignition coil assembly (ignition signal) Idling Pulse generation
(see waveform 12)
D1-36 (IGT5) - D1-81 (E1) P - BR No. 5 ignition coil assembly (ignition signal) Idling Pulse generation
(see waveform 12)
D1-35 (IGT6) - D1-81 (E1) V - BR No. 6 ignition coil assembly (ignition signal) Idling Pulse generation
(see waveform 12)
D1-106 (IGF1) - D1-81 (E1) Y - BR Ignition coil assembly (ignition confirmation signal) Engine switch on (IG) 4.5 to 5.5 V
Idling Pulse generation
(see waveform 12)
D1-41 (GE01) - D1-81 (E1) BR - BR Shielded earth (ground) circuit of throttle actuator Always Below 1 Ω
D1-88 (OX1B) - D1-65 (EX1B) W - GR Heated oxygen sensor (bank 1 sensor 2) signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
(see waveform 13)
D1-87 (OX2B) - D1-64 (EX2B) B - B-W Heated oxygen sensor (bank 2 sensor 2) signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
(see waveform 13)
D1-99 (VTA2) - D1-97 (ETA) GR - W Throttle position sensor signal (for sensor malfunction detection) Engine switch on (IG), accelerator pedal fully released 2.1 to 3.1 V
Engine switch on (IG), accelerator pedal fully depressed 4.6 to 5.0 V
D1-98 (VTA1) - D1-97 (ETA) Y - W Throttle position sensor signal (for engine control) Engine switch on (IG), accelerator pedal fully released 0.5 to 1.1 V
Engine switch on (IG), accelerator pedal fully depressed 3.2 to 4.8 V
D1-79 (THW) - D1-78 (ETHW) L - BR Engine coolant temperature sensor signal Idling, engine coolant temperature 80°C (176°F) 0.2 to 1.0 V
D1-71 (THA) - D1-74 (ETHA) P - G-R Intake air temperature sensor signal Idling, intake air temperature 20°C (68°F) 0.5 to 3.4 V
D1-72 (VG) - D1-73 (E2G) GR - LG Mass air flow meter sub-assembly signal Idling, shift lever in P or N, A/C switch OFF 0.5 to 3.0 V
D1-107 (ACIS) - D1-81 (E1) R - BR Intake air control valve assembly (for acoustic control induction system) operation signal Engine switch on (IG) 11 to 14 V
D1-108 (PRG) - D1-81 (E1) L - BR Purge VSV operation signal Engine switch on (IG) 11 to 14 V
Idling with warm engine Pulse generation
(see waveform 14)
D1-109 (HA2A) - D1-46 (E05) B - BR Air fuel ratio sensor (bank 2 sensor 1) heater operation signal Idling Pulse generation
(see waveform 15)
Engine switch on (IG) 11 to 14 V
D1-86 (HA1A) - D1-46 (E05) G - BR Air fuel ratio sensor (bank 1 sensor 1) heater operation signal Idling Pulse generation
(see waveform 15)
Engine switch on (IG) 11 to 14 V
D1-20 (ME01) - Body ground BR - - Earth (ground) circuit of ECM Always Below 1 Ω
D1-104 (E03) - Body ground BR - - Earth (ground) circuit of ECM Always Below 1 Ω
D1-48 (HT1B) - D1-81 (E1) LG - BR Heated oxygen sensor (bank 2 sensor 2) heater operation signal Idling Below 3.0 V
Engine switch on (IG) 11 to 14 V
D1-47 (HT2B) - D1-81 (E1) Y - BR Heated oxygen sensor (bank 2 sensor 2) heater operation signal Idling Below 3.0 V
Engine switch on (IG) 11 to 14 V
D1-46 (E05) - Body ground BR - - Earth (ground) circuit of ECM Always Below 1 Ω
D1-23 (E04) - Body ground W-B - - Earth (ground) circuit of ECM Always Below 1 Ω
D1-62 (NSW) - D1-81 (E1) L-B - BR Park/Neutral position switch assembly signal Engine switch on (IG), shift lever in P or N Below 3.0 V
Engine switch on (IG), shift lever not in P or N 11 to 14 V
D1-118 (KNK2) - D1-117 (EKN2) B - W Knock control sensor (bank 2) signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(see waveform 16)
D1-95 (KNK1) - D1-94 (EKNK) R - G Knock control sensor (bank 1) signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(see waveform 16)
D1-93 (A1A+) - D1-81 (E1) W - BR Air fuel ratio sensor (bank 1 sensor 1) signal Engine switch on (IG) 3.3 V*1
D1-120 (A2A+) - D1-81 (E1) L - BR Air fuel ratio sensor (bank 2 sensor 1) signal Engine switch on (IG) 3.3 V*1
D1-116 (A1A-) - D1-81 (E1) BR - BR Air fuel ratio sensor (bank 1 sensor 1) signal Engine switch on (IG) 2.9 V*1
D1-119 (A2A-) - D1-81 (E1) Y - BR Air fuel ratio sensor (bank 2 sensor 1) signal Engine switch on (IG) 2.9 V*1
D1-24 (P) - D1-81 (E1) V - BR P shift position switch signal Engine switch on (IG) and shift lever in P 11 to 14 V
Engine switch on (IG) and shift lever not in P Below 1 V
D1-25 (R) - D1-81 (E1) R - BR R shift position switch signal Engine switch on (IG) and shift lever in R 11 to 14 V
Engine switch on (IG) and shift lever not in R Below 1 V
D1-27 (N) - D1-81 (E1) L-B - BR N shift position switch signal Engine switch on (IG) and shift lever in N 11 to 14 V
Engine switch on (IG) and shift lever not in N Below 1 V
D1-26 (D) - D1-81 (E1) L - BR D shift position switch signal Engine switch on (IG) and shift lever in D 11 to 14 V
Engine switch on (IG) and shift lever not in D Below 1 V
A7-25 (S) - D1-81 (E1) Y - BR S shift position switch signal Engine switch on (IG) and shift lever in S 11 to 14 V
Engine switch on (IG) and shift lever not in S Below 1 V
A7-51 (SFTD) - D1-81 (E1) GR - BR Down shift switch signal Engine switch on (IG) and shift lever in "S" 11 to 14 V
Engine switch on (IG) and shift lever in "-" selected (Down shift) Below 1 V
A7-16 (SFTU) - D1-81 (E1) P - BR Up shift switch signal Engine switch on (IG) and shift lever in "S" 11 to 14 V
Engine switch on (IG) and shift lever in "+" selected (Up shift) Below 1 V
D1-80 (VCIB) - D1-101 (EIB) LG - P Power source of battery current sensor Engine switch on (IG) 4.5 to 5.0 V
D1-100 (IB) - D1-101 (EIB) R - P Battery current sensor Engine switch on (IG) 0.5 to 4.5 V
D1-103 (THB) - D1-101 (EIB) G-R - P Battery current sensor Engine switch on (IG) 0.5 to 4.5 V
D1-59 (FPR) - D1-81 (E1) W - BR Fuel pump control Cranking 11 to 14 V
Idling 11 to 14 V

*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

WAVEFORM 1


U188237E02
0.427,0.208 0.969,0.406 0.542,0.198 10 false 5 V/DIV. 0.375,1.188 0.76,1.385 0.385,0.198 10 false GND 1.688,1.938 2.438,2.104 0.75,0.167 10 false 10 ms./DIV.

Engine speed signal
ECM Terminal Name Between TACH and E1
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 2


A295060E05
2.896,1.198 3.354,1.396 0.458,0.198 10 false GND 1.094,1.969 2.396,2.167 1.302,0.198 10 false 20 ms./DIV. 2.667,0.135 3.344,0.49 0.677,0.354 10 false 5 V/DIV.

Vehicle speed signal
ECM Terminal Name Between SPD and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 3


A395913E01
2.771,0.24 3.333,0.427 0.563,0.188 10 false 1 V/DIV. 2.99,1.396 3.344,1.583 0.354,0.188 10 false GND 1.417,1.917 2.156,2.125 0.74,0.208 10 false 10 μs./DIV.

CAN communication signal (reference)
ECM Terminal Name Between CANH and E1, or CAN+ and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 4


A395914E01
2.792,0.208 3.365,0.406 0.573,0.198 10 false 1 V/DIV. 3.01,1.375 3.365,1.542 0.354,0.167 10 false GND 1.406,1.906 2.125,2.073 0.719,0.167 10 false 10 μs./DIV.

CAN communication signal (reference)
ECM Terminal Name Between CANL and E1, or CAN- and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 5


A381226E01
0.521,0.167 1.25,0.448 0.729,0.281 10 false 20 V/DIV. 0.615,1.583 1.344,1.865 0.729,0.281 10 false GND 1.625,1.927 3.427,2.177 1.802,0.25 10 true 20 ms./DIV.

No. 1 (to No. 6) fuel injector assembly signal
ECM Terminal Name Between #10 (to #60) and E01
Tester Range 20 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 6


U113547E06
0.583,0.229 1.125,0.427 0.542,0.198 10 false 5 V/DIV. 0.594,1.115 0.938,1.313 0.344,0.198 10 false GND 1.865,1.854 2.542,2.052 0.677,0.198 10 false 1 ms./DIV.

Camshaft timing oil control valve assembly (for intake camshaft) operation signal
ECM Terminal Name Between OC1+ and OC1-, or OC2+ and OC2-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 7


A207436E13
0.292,1.229 0.583,1.458 0.292,0.229 10 false NE 2.99,1.25 3.365,1.469 0.375,0.219 10 false GND 2.635,0.604 3.271,0.854 0.635,0.25 10 false 5 V/DIV. 2.99,1.802 3.354,2.042 0.365,0.24 10 false GND 2.99,2.198 3.354,2.417 0.365,0.219 10 false GND 1.292,2.49 2.198,2.75 0.906,0.26 10 false 20 ms./DIV. 0.208,1.74 0.552,1.917 0.344,0.177 10 false VV1 0.208,2.031 0.552,2.25 0.344,0.219 10 false VV2

Crankshaft position sensor signal and VVT sensor (for intake camshaft) signal
ECM Terminal Name Between NE+ and NE-
Between VV1+ and VV1-
Between VV2+ and VV1-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 8


A207435E10
0.292,1.198 0.604,1.438 0.313,0.24 10 false NE 2.99,1.208 3.365,1.448 0.375,0.24 10 false GND 2.635,0.698 3.292,0.948 0.656,0.25 10 false 5 V/DIV. 2.99,1.76 3.344,1.979 0.354,0.219 10 false GND 2.99,2.156 3.344,2.396 0.354,0.24 10 false GND 1.281,2.458 2.083,2.688 0.802,0.229 10 false 20 ms./DIV. 0.198,1.719 0.531,1.938 0.333,0.219 10 false EV1 0.198,2 0.531,2.198 0.333,0.198 10 false EV2

Crankshaft position sensor signal and VVT sensor (for exhaust camshaft) signal
ECM Terminal Name Between NE+ and NE-
Between EV1+ and EV1-
Between EV2+ and EV2-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 9


U113547E06
0.583,0.229 1.125,0.427 0.542,0.198 10 false 5 V/DIV. 0.594,1.115 0.938,1.313 0.344,0.198 10 false GND 1.865,1.854 2.542,2.052 0.677,0.198 10 false 1 ms./DIV.

Camshaft timing oil control valve assembly (for exhaust camshaft) operation signal
ECM Terminal Name Between OE1+ and OE1-, or OE2+ and OE2-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 10


A208000E60
2.856,0.973 3.187,1.119 0.331,0.147 10 GND 2.631,0.216 3.176,0.36 0.545,0.144 10 5 V/DIV. 0.501,0.616 0.722,0.759 0.221,0.143 10 M+ 1.323,1.806 1.995,1.965 0.672,0.159 10 1 ms./DIV.

Throttle actuator operation signal (positive terminal)
ECM Terminal Name Between M+ and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 11


A245848E54
2.849,0.99 3.182,1.142 0.333,0.151 10 GND 2.627,0.266 3.166,0.409 0.539,0.142 10 5 V/DIV. 0.479,0.626 0.664,0.777 0.184,0.15 10 M- 1.323,1.82 1.996,1.967 0.672,0.147 10 1 ms./DIV.

Throttle actuator operation signal (negative terminal)
ECM Terminal Name Between M- and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 12


A210049E17
2.875,1.708 3.344,1.969 0.469,0.26 10 false GND 2.875,2.583 3.292,2.802 0.417,0.219 10 false GND 1.177,2.719 1.979,2.948 0.802,0.229 10 false 20 ms./DIV. 2.5,0.521 3.167,0.802 0.667,0.281 10 false 2 V/DIV. 0.156,1.219 0.51,1.448 0.354,0.229 10 false IGT 0.156,2.063 0.427,2.271 0.271,0.208 10 false IGF

Ignition coil assembly signal (IGT and IGF signal)
ECM Terminal Name Between IGT (1 to 6) and E1
Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 13


U113545E10
0.396,0.188 1.063,0.406 0.667,0.219 10 false 0.2 V/DIV. 0.552,1.479 0.917,1.677 0.365,0.198 10 false GND 1.74,1.875 3.427,2.177 1.688,0.302 10 true 200 ms./DIV.

Heated oxygen sensor signal
ECM Terminal Name Between OX1B and EX1B, or OX2B and EX2B
Tester Range 0.2 V/DIV., 200 ms./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:

In the DATA LIST, item O2S B1S2, O2S B2S2 shows the ECM values from the heated oxygen sensor.



WAVEFORM 14


G042964E13
0.5,1.177 0.854,1.333 0.354,0.156 10 false GND 0.385,0.24 1.01,0.396 0.625,0.156 10 false 10 V/DIV. 1.708,1.885 2.448,2.042 0.74,0.156 10 false 50 ms./DIV.

Purge VSV operation signal
ECM Terminal Name Between PRG and E1
Tester Range 10 V/DIV., 50 ms./DIV.
Condition Idling with warm engine

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 15


A205412E21
2.646,0.073 3.25,0.26 0.604,0.188 10 false 5 V/DIV. 2.698,0.906 3.063,1.073 0.365,0.167 10 false GND 1.115,1.854 1.875,2.031 0.76,0.177 10 false 10 ms./DIV.

Air fuel ratio sensor heater operation signal
ECM Terminal Name Between HA1A and E05, or HA2A and E05
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling

HINT:

The wavelength varies in accordance with the engine operating condition.



WAVEFORM 16


A194185E11
2.969,1.615 3.313,1.781 0.344,0.167 10 false GND 2.74,1.094 3.271,1.271 0.531,0.177 10 false 1 V/DIV. 1.219,2.573 1.917,2.75 0.698,0.177 10 false 1 ms./DIV.

Knock control sensor signal
ECM Terminal Name Between KNK1 and EKNK, or KNK2 and EKN2
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle condition.