Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM D

2GR-FE ENGINE CONTROL  SFI SYSTEM  FREEZE FRAME DATA  


DESCRIPTION


The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

HINT:

If it is impossible to replicate the problem even though a DTC is detected, confirm the freeze frame data.



A317524E35
0.375,1.125 2.063,1.323 1.688,0.198 10 false 0.5 seconds 1.302,1.135 2.99,1.333 1.688,0.198 10 false 0.5 seconds 2.26,1.135 3.427,1.375 1.167,0.24 10 false 0.5 seconds 2.396,0.25 3.198,0.479 0.802,0.229 10 false DTC stored 0.396,2.792 2.875,3.063 2.479,0.271 10 false Freeze frame data which can be read

The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the GTS, 5 separate sets of freeze frame data can be checked.

-

3 data sets before the DTC was stored.

-

1 data set when the DTC was stored.

-

1 data set after the DTC was stored.


These data sets can be used to simulate the condition of the vehicle around the time of the occurrence the malfunction. The data may assist in identifying the cause of the malfunction, and judging whether it was temporary or not.




LIST OF FREEZE FRAME DATA


Tester Display Measurement Item Diagnostic Note
Vehicle Speed Vehicle speed Speed indicated on speedometer
Engine Speed Engine speed -
Calculate Load Calculated load Calculated load by ECM
Vehicle Load Vehicle load -
MAF Mass air flow volume If value is approximately 0.0 gm/sec:
·

Mass air flow meter power source circuit open or short


·

VG circuit open or short


If value is 271.0 gm/sec or more:
·

E2G circuit open


Atmosphere Pressure Atmospheric pressure -
Coolant Temp Engine coolant temperature If value is -40°C (-40°F), sensor circuit open
If value is 140°C (284°F), sensor circuit shorted
Intake Air Intake air temperature If value is -40°C (-40°F), sensor circuit open
If value is 140°C (284°F), sensor circuit shorted
Ambient Temperature Ambient temperature -
Engine Run Time Accumulated engine running time -
Initial Engine Coolant Temp Engine coolant temperature at engine start -
Initial Intake Air Temp Intake air temperature at engine start -
Battery Voltage Battery voltage -
Accel Sens. No. 1 Volt % Absolute accelerator pedal position No. 1 -
Accel Sens. No. 2 Volt % Absolute accelerator pedal position No. 2 -
Throttle Sensor Volt % Absolute throttle position sensor No. 1 -
Throttl Sensor #2 Volt % Absolute throttle position sensor No. 2 -
Throttle Sensor Position Throttle sensor position -
Throttle Motor DUTY Throttle actuator -
Throttle Position Throttle position When the engine stalls, is difficult to start, or idles roughly.
ISC Flow Flow rate calculated using information from mass air flow meter sub-assembly When the engine stalls, is difficult to start, or idles roughly.
ISC Position Requested throttle opening amount calculated using ISC control When the engine stalls, is difficult to start, or idles roughly.
ISC Feedback Value ISC feedback amount When the engine stalls, is difficult to start, or idles roughly.
ISC Learning Value ISC learned air flow value When the engine stalls, is difficult to start, or idles roughly.
Electric Load Feedback Val Compensation flow rate according to electrical load When the engine stalls, is difficult to start, or idles roughly.
Air Conditioner FB Val Compensation flow rate according to air conditioner load When the engine stalls, is difficult to start, or idles roughly.
Low Revolution Control Low engine speed control operation state When the engine stalls, is difficult to start, or idles roughly.
N Range Status Shift lever N status When the engine stalls, is difficult to start, or idles roughly.
Eng Stall Control FB Flow Intake air compensation flow rate
·

The intake air amount and ignition timing are adjusted when there is a large decrease in engine speed (for example, a decrease to 550 rpm or less) in order to prevent engine stall.

·

For use when engine stall, starting problems or rough idle is present.


Deposit Loss Flow Flow loss due to deposits
·

This value indicates the amount of compensation for a decrease in flow passage area due to the buildup of deposits on the throttle valve.

·

Check this value for reference when the engine stalls, is difficult to start, or idles roughly.

·

When the ISC learned value is initialized, performing the following procedures in order to quickly relearn the Deposit Loss Flow value. After the Deposit Loss Flow has been relearned, gradual fine adjustments will continue automatically.

-

Start the engine cold and allow the engine to idle.

-

After the engine is warmed up (engine coolant temperature is above 80°C [176°F]), allow the engine to idle for an additional 5 minutes.

-

Turn the engine switch off and wait for 30 seconds.

-

Start the engine again, and allow the engine to idle for 5 minutes.



Injector (Port) Injection period of the No. 1 cylinder -
Injection Volum (Cylinder 1) Injection volume (cylinder 1) -
Fuel Pump Speed Control FUEL PMP relay status -
Fuel Pump/Speed Status Fuel pump status -
EVAP (Purge) VSV Purge VSV duty ratio -
Evap Purge Flow Purge flow -
Purge Density Learn Value Learning value of purge density -
EVAP Purge VSV Purge VSV -
Target Air-Fuel Ratio Target air fuel ratio -
AF Lambda B1S1 Fuel trim at air fuel ratio sensor (bank 1 sensor 1) -
AF Lambda B2S1 Fuel trim at air fuel ratio sensor (bank 2 sensor 1) -
AFS Voltage B1S1 Air fuel ratio sensor output voltage (bank 1 sensor 1) -
AFS Voltage B2S1 Air fuel ratio sensor output voltage (bank 2 sensor 1) -
AFS Current B1S1 Air fuel ratio sensor output current (bank 1 sensor 1) -
AFS Current B2S1 Air fuel ratio sensor output current (bank 2 sensor 1) -
O2S B1S2 Heated oxygen sensor output voltage (bank 1 sensor 2) -
O2S B2S2 Heated oxygen sensor output voltage (bank 2 sensor 2) -
Short FT #1 Short-term fuel trim (bank 1) Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
Long FT #1 Long-term fuel trim (bank 1) Overall fuel compensation carried out in long-term to compensate for a continual deviation of short-term fuel trim from central valve
Total FT #1 Total fuel trim (bank 1) -
Short FT #2 Short-term fuel trim (bank 2) Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
Long FT #2 Long-term fuel trim (bank 2) Overall fuel compensation carried out in long-term to compensate for a continual deviation of short-term fuel trim from central valve
Total FT #2 Total fuel trim (bank 2) -
Fuel System Status #1 Fuel system status (bank 1)
·

OL (Open Loop): Has not yet satisfied conditions to go closed loop


·

CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control


·

OLDrive: Open loop due to driving conditions (fuel enrichment)


·

OLFault: Open loop due to detected system fault


·

CLFault: Closed loop but air fuel ratio sensor, which used for fuel control malfunctioning


Fuel System Status #2 Fuel system status (bank 2)
·

OL (Open Loop): Has not yet satisfied conditions to go closed loop


·

CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control


·

OLDrive: Open loop due to driving conditions (fuel enrichment)


·

OLFault: Open loop due to detected system fault


·

CLFault: Closed loop but air fuel ratio sensor, which used for fuel control malfunctioning


IGN Advance Ignition advance -
Knock Feedback Value Feedback value of knocking -
Knock Correct Learn Value Correction learning value of knocking -
Idle Spark Advn Ctrl #1 Individual cylinder timing advance compensation amount (No. 1) When the engine stalls, is difficult to start, or idles roughly.
Idle Spark Advn Ctrl #2 Individual cylinder timing advance compensation amount (No. 2) When the engine stalls, is difficult to start, or idles roughly.
Idle Spark Advn Ctrl #3 Individual cylinder timing advance compensation amount (No. 3) When the engine stalls, is difficult to start, or idles roughly.
Idle Spark Advn Ctrl #4 Individual cylinder timing advance compensation amount (No. 4) When the engine stalls, is difficult to start, or idles roughly.
Idle Spark Advn Ctrl #5 Individual cylinder timing advance compensation amount (No. 5) When the engine stalls, is difficult to start, or idles roughly.
Idle Spark Advn Ctrl #6 Individual cylinder timing advance compensation amount (No. 6) When the engine stalls, is difficult to start, or idles roughly.
ACIS VSV Intake air control valve assembly for acoustic control induction system -
VVT Control Status #1 VVT control status (bank 1) -
VVT Control Status #2 VVT control status (bank 2) -
VVT Advance Fail VVT control failure status -
Catalyst Temp B1S1 Estimated catalyst temperature (bank 1 sensor 1) -
Catalyst Temp B2S1 Estimated catalyst temperature (bank 2 sensor 1) -
Catalyst Temp B1S2 Estimated catalyst temperature (bank 1 sensor 2) -
Catalyst Temp B2S2 Estimated catalyst temperature (bank 2 sensor 2) -
Starter Signal Starter signal -
Starter Control Starter control -
Power Steering Signal Power steering signal -
Starter Relay Starter relay -
Power Steer. Sig. Record Power steering signal -
ACC Relay ACC relay -
Neutral Position SW Signal Park/Neutral position switch assembly signal -
Stop Light Switch Stop light switch assembly -
A/C Signal A/C signal -
Closed Throttle Position SW Closed throttle position switch -
Electrical Load Signal Electrical load signal -
Time after DTC Cleared Cumulative time after DTC cleared -
Distance from DTC Cleared Accumulated distance after DTC cleared -
Warmup Cycle Cleared DTC Warm-up cycle after DTC cleared -
TC and TE1 TC and TE1 terminals of DLC3 -
Ignition Trig. Count Ignition count -
Cylinder #1 Misfire Count Cylinder #1 misfire count -
Cylinder #2 Misfire Count Cylinder #2 misfire count -
Cylinder #3 Misfire Count Cylinder #3 misfire count -
Cylinder #4 Misfire Count Cylinder #4 misfire count -
Cylinder #5 Misfire Count Cylinder #5 misfire count -
Cylinder #6 Misfire Count Cylinder #6 misfire count -
All Cylinders Misfire Count All cylinders misfire count -
Misfire RPM Engine speed when misfire occurs -
Misfire Load Engine load when misfire occurs -
Misfire Margin Margin to detect engine misfire -
Engine Starting Time Time elapsed before engine starts (interval between engine switch on (IG) and off) When the engine stalls, is difficult to start, or idles roughly.
Engine Speed (Starter Off) Engine speed when starter off When the engine stalls, is difficult to start, or idles roughly.
Starter Count Number of times starter turned on after engine switch on (IG) When the engine stalls, is difficult to start, or idles roughly.
Run Dist of Previous Trip Distance driven during previous trip When the engine stalls, is difficult to start, or idles roughly.
Previous Trip Coolant Temp Engine coolant temperature during previous trip When the engine stalls, is difficult to start, or idles roughly.
Previous Trip Intake Temp Intake air temperature during previous trip When the engine stalls, is difficult to start, or idles roughly.
Engine Oil Temperature Engine oil temperature (estimated temperature) When the engine stalls, is difficult to start, or idles roughly.
Previous Trip Eng Oil Temp Engine oil temperature during previous trip When the engine stalls, is difficult to start, or idles roughly.
Ambient Temp for A/C Ambient temperature for A/C When the engine stalls, is difficult to start, or idles roughly.
Previous Trip Ambient Temp Ambient temperature during previous trip When the engine stalls, is difficult to start, or idles roughly.
Engine Start Hesitation History of hesitation during engine start This value changes to ON when the engine speed does not reach 500 rpm during cranking.
Low Rev for Eng Start History of low engine speed after engine start -
Minimum Engine Speed Minimum engine speed When the engine stalls, is difficult to start, or idles roughly.
Electric Fan Motor Electric fan motor -
Idle Fuel Cut Fuel cut at idle ON: when throttle valve fully closed and engine speed over 2800 rpm
FC TAU FC TAU Fuel cut being performed with a very light load to prevent incomplete engine combustion
Immobiliser Fuel Cut Status of immobiliser fuel cut -
Received MIL from ECT MIL status from ECT -
Shift Position Sig from ECT Shift position signal from ECT -
A/T Oil Temp from ECT ATF temperature from ECT -
SPD (NO) Output shaft speed -
ECT Lock Up ECT lock up -
Shift SW Status (P Range) Shift switch status (P range) -
Shift SW Status (R Range) Shift switch status (R range) -
Shift SW Status (N Range) Shift switch status (N range) -
Sports Shift Up SW Sports shift up switch status -
Sports Shift Down SW Sports shift down switch status -
Sports Mode Selection SW Sports mode selection switch status -
Shift SW Status (D Range) Shift switch status (D range) -