Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0420  Catalyst System Efficiency Below Threshold (Bank 1)  


MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.

The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.

In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the voltage output of the heated oxygen sensor while performing active air fuel ratio control.

The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the cycle of the waveform for the heated oxygen sensor is long, the oxygen storage capacity is great. There is a direct correlation between the heated oxygen sensor and the oxygen storage capacity of the three-way catalytic converter.

The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, the ECM illuminates the MIL and stored the DTC.

This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.

DTC No. DTC Detection Condition Trouble Area
P0420 The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic).
·

Gas leak from exhaust system

·

Air fuel ratio sensor (sensor 1)

·

Heated oxygen sensor (sensor 2)

·

Exhaust manifold converter sub-assembly (TWC: Front catalyst) and center exhaust pipe assembly (TWC: Rear catalyst)



CATALYST LOCATION

A230568E02
0.988,0.698 1.144,0.849 0.156,0.151 10 *1 0.95,0.773 0.81,0.773 0.81,0.773 0.626,1.106 false 1.436,2.463 1.592,2.614 0.156,0.151 10 *3 1.399,2.535 1.259,2.535 1.259,2.535 1.075,2.342 false 1.814,1.104 1.970,1.255 0.156,0.151 10 *4 1.775,1.183 1.634,1.183 1.634,1.183 1.275,1.836 false 3.821,0.773 3.961,0.773 3.961,0.773 4.316,1.422 false 0.077,0.698 0.233,0.849 0.156,0.151 10 *2 0.248,0.773 0.389,0.773 0.389,0.773 0.389,1.535 false 3.65,0.698 3.806,0.849 0.156,0.151 10 *5 5.586,0.353 5.726,0.353 5.726,0.353 5.852,0.58 false 5.415,0.278 5.571,0.429 0.156,0.151 10 *6

Text in Illustration
*1 Exhaust Manifold Converter Sub-assembly
(TWC: Front Catalyst)
*2 Air fuel ratio Sensor
*3 Front Exhaust Pipe Assembly *4 Heated oxygen Sensor
*5 Center Exhaust Pipe Assembly
(TWC: Rear Catalyst)
*6 Tail Pipe Assembly

NOTICE:

Replace the exhaust manifold converter sub-assembly (*1) and the center exhaust pipe assembly (*5) together when catalyst replacement is necessary. (Excluding air fuel ratio sensor *2 and heated oxygen sensor *4)


CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.


A387619E01
1.333,0.865 1.698,0.469 1.698,0.469 1.854,0.469 false 0.729,1.146 1.385,1.406 0.656,0.26 10 false 60 km/h 0.938,2.208 1.406,2.458 0.469,0.25 10 false Idling 0.198,2.458 1.396,2.74 1.198,0.281 10 false Engine Switch off 0.375,3.438 4.969,3.74 4.594,0.302 10 false *: Drive the vehicle while keeping the engine load as constant as possible 1.896,0.396 3.542,0.708 1.646,0.313 10 false Between 75 to 100 km/h 1.677,2.104 1.948,2.344 0.271,0.24 10 false [A] 1.375,2.719 2.229,2.99 0.854,0.271 10 false Warming up 2.615,1.021 2.938,1.281 0.323,0.26 10 false [B]* 2.365,2.76 3.083,3.115 0.719,0.354 10 false 10 minutes or more 3.156,3.156 3.458,3.417 0.302,0.26 10 false [C] 3.49,2.115 3.781,2.365 0.292,0.25 10 false [D] 3.375,2.719 3.99,3.073 0.615,0.354 10 false Warming up 4.406,1.052 4.74,1.323 0.333,0.271 10 false [E]* 4.135,2.76 4.844,3.177 0.708,0.417 10 false 10 minutes or more 5.021,3.167 5.323,3.438 0.302,0.271 10 false [F] 6.167,0.656 6.531,0.938 0.365,0.281 10 false [G]* 5.906,2.719 6.635,3.25 0.729,0.531 10 false 10 minutes or more 6.781,3.146 7.031,3.385 0.25,0.24 10 false [H]

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Turn the engine switch on (IG) and turn the GTS on.

7.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

8.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


9.

Turn the engine switch off and wait for at least 30 seconds [C].

10.

Turn the engine switch on (IG) and turn the GTS on.

11.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [D].

12.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


13.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].

14.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



15.

Drive the vehicle at a speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes or more [G].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


16.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [H].

17.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




CONDITIONING FOR SENSOR TESTING

HINT:

Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is to activate the sensors sufficiently to obtain appropriate inspection results.


A292989E18
4.875,3.094 4.875,3.344 false 5.177,3.094 5.177,3.344 false 4.875,3.344 5.458,3.344 false 0.583,0.688 1.51,0.927 0.927,0.24 10 false Engine Speed 0.865,1.031 1.479,1.26 0.615,0.229 10 false 3000 rpm 0.865,1.573 1.542,1.771 0.677,0.198 10 false 2000 rpm 1.104,2.542 1.594,2.802 0.49,0.26 10 false Idling 0.365,2.802 1.521,3 1.156,0.198 10 false Engine Switch off 2.104,3.167 2.958,3.396 0.854,0.229 10 false Warming up 3.333,3.167 4.531,3.385 1.198,0.219 10 false At least 3 minutes 5.5,3.26 6.198,3.51 0.698,0.25 10 false 2 seconds 4.865,3.396 5.333,3.583 0.469,0.188 10 false Check 6.615,2.76 6.958,3 0.344,0.24 10 false Time 1.646,2.656 1.885,2.896 0.24,0.24 10 false (a) 2.094,2.417 2.354,2.677 0.26,0.26 10 false (b) 2.76,2.427 2.99,2.656 0.229,0.229 10 false (c) 4.802,0.875 5.052,1.156 0.25,0.281 10 false (e) 5.104,1.458 5.323,1.729 0.219,0.271 10 false (e) 3.656,0.896 3.896,1.073 0.24,0.177 10 false (d)

(a) Connect the GTS to the DLC3.

(b) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes.

(c) Enter the following menus: Powertrain / Engine and ECT / Data List / AFS Voltage B1S1 and O2S B1S2.

(d) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes.

(e) While running the engine at 3000 rpm for 2 seconds, and then 2000 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the GTS.


HINT:
·

If the voltage output of either the air fuel ratio or heated oxygen sensor does not fluctuate, or there is a noise in the waveform of either sensor, the sensor may be malfunctioning.

·

If the voltage outputs of both the sensors remain lean or rich, the air fuel ratio may be extremely lean or rich. In such cases, perform the Control the Injection Volume for A/F Sensor Active Test using the GTS.

·

If the Three-way Catalytic Converter (TWC) has deteriorated, the heated oxygen sensor (located behind the Three-way Catalytic Converter [TWC]) voltage output fluctuates up and down frequently, even under normal driving conditions (active air fuel ratio control is not performed).


A199479E33
0.25,0.104 4.646,0.365 4.396,0.26 10 false Voltage Output When Active Air Fuel Ratio Control Not Performed: 2.438,0.531 3.573,0.698 1.135,0.167 10 false Normal Catalyst 4.76,0.542 6.135,0.729 1.375,0.188 10 false Deteriorated Catalyst 2.406,2.99 3.281,3.188 0.875,0.198 10 false 10 seconds 4.958,3 5.792,3.167 0.833,0.167 10 false 10 seconds 1.49,0.781 1.875,0.927 0.385,0.146 10 false 3.4 V 1.479,1.208 1.865,1.354 0.385,0.146 10 false 3.1 V 1.49,2.052 1.885,2.26 0.396,0.208 10 false 1.0 V 1.604,2.729 1.917,2.958 0.313,0.229 10 false 0 V 0.052,2.188 1.333,2.99 1.281,0.802 10 false Waveform of Heated Oxygen Sensor Behind Three-Way Catalytic Converter 0.063,0.76 1.406,1.417 1.344,0.656 10 false Waveform of Air Fuel Ratio Sensor in Front of Three-Way Catalytic Converter


CAUTION / NOTICE / HINT

HINT:
·

If a malfunction cannot be found when troubleshooting DTC P0420, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P0171 (System Too Lean) and P0172 (System Too Rich).

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0420 is output A
DTC P0420 and other DTCs are output B

HINT:

If any DTCs other than P0420 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up.


c.

Turn the GTS on.


d.

Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Data List / AFS Voltage B1S1 and O2S B1S2.


f.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).


g.

Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard:
GTS Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V


Result
Status
AFS Voltage B1S1
Status
O2S B1S2
Actual air fuel ratio, air fuel ratio sensor and
heated oxygen sensor condition
Misfire Main Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal -
·

Three-way catalytic converter

·

Gas leak from exhaust system


A
Lean Lean/Rich Air fuel ratio sensor malfunction -
·

Air fuel ratio sensor


B
Rich Lean/Rich Air fuel ratio sensor malfunction -
·

Air fuel ratio sensor


Lean/Rich Lean Heated oxygen sensor malfunction -
·

Heated oxygen sensor

·

Gas leak from exhaust system


C
Lean/Rich Rich Heated oxygen sensor malfunction -
·

Heated oxygen sensor

·

Gas leak from exhaust system


Lean Lean Actual air fuel ratio lean May occur
·

Extremely rich or lean actual air fuel ratio

·

Gas leak from exhaust system


D
Rich Rich Actual air fuel ratio rich -
·

Extremely rich or lean actual air fuel ratio

·

Gas leak from exhaust system



Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.

Rich: During Control the Injection Volume for A/F Sensor, the AFS Voltage B1S1 is consistently below 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.

Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the air fuel ratio sensor or heated oxygen sensor alternate correctly.




A

3.CHECK FOR EXHAUST GAS LEAK

B

5.REPLACE AIR FUEL RATIO SENSOR

C

6.CHECK FOR EXHAUST GAS LEAK

D

8.CHECK FOR EXHAUST GAS LEAK
3.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.




OK

4.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND CENTER EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

NG

10.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
4.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND CENTER EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)
NOTICE:

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) and the center exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.


HINT:

Confirm the replacement parts, referring to the illustration in the Catalyst Location.


a.

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) (See page Engine / Hybrid System>2AZ-FE ENGINE MECHANICAL>ENGINE UNIT>COMPONENTS).


b.

Replace the center exhaust pipe assembly (TWC: Rear catalyst) (See page Engine / Hybrid System>2AZ-FE EXHAUST>EXHAUST PIPE>COMPONENTS).



NEXT

END

5.REPLACE AIR FUEL RATIO SENSOR
a.


NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
6.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.




OK

7.REPLACE HEATED OXYGEN SENSOR

NG

10.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
7.REPLACE HEATED OXYGEN SENSOR
a.


NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
8.CHECK FOR EXHAUST GAS LEAK
a.

Check the exhaust gas leaks.

OK:

No gas leaks.




OK

9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO

NG

10.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
a.

Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>P0171).



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
10.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
a.

Repair or replace exhaust gas leak point.



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Result
Result Proceed to
DTC P0420 is output A
DTC is not output
(Pending DTCs is not output)
B



A

12.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND CENTER EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

B

END

12.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND CENTER EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)
NOTICE:

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) and the center exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.


HINT:

Confirm the replacement parts, referring to the illustration in the Catalyst Location.


a.

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) (See page Engine / Hybrid System>2AZ-FE ENGINE MECHANICAL>ENGINE UNIT>COMPONENTS).


b.

Replace the center exhaust pipe assembly (TWC: Rear catalyst) (See page Engine / Hybrid System>2AZ-FE EXHAUST>EXHAUST PIPE>COMPONENTS).



NEXT

END