Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM U

2AZ-FE ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


U188252E02
2.24,0.292 2.458,0.469 0.219,0.177 10 false D2 5.625,0.281 5.833,0.438 0.208,0.156 10 false A7

HINT:

The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
A7-20 (BATT) - D2-104 (E1) W - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
A7-2 (+B) - D2-104 (E1) B - BR Power source of ECM Engine switch on (IG) 11 to 14 V
A7-1 (+B2) - D2-104 (E1) B - BR Power source of ECM Engine switch on (IG) 11 to 14 V
A7-3 (+BM) - D2-104 (E1) R - BR Power source of throttle actuator Always 11 to 14 V
D2-85 (IGT1) - D2-104 (E1)
D2-84 (IGT2) - D2-104 (E1)
D2-83 (IGT3) - D2-104 (E1)
D2-82 (IGT4) - D2-104 (E1)
W - BR
Y - BR
G - BR
G - BR
Ignition coil
(ignition signal)
Idling Pulse generation
(see waveform 1)
D2-81 (IGF1) - D2-104 (E1) R - BR Ignition coil
(ignition confirmation signal)
Engine switch on (IG) 4.5 to 5.5 V
Idling Pulse generation
(see waveform 1)
D2-122 (NE+) - D2-121 (NE-) R - G Crankshaft position sensor Idling Pulse generation
(see waveform 2)
D2-99 (G2+) - D2-98 (G2-) L - Y Camshaft position sensor Idling Pulse generation
(see waveform 2)
D2-108 (#10) - D2-104 (E1)
D2-107 (#20) - D2-104 (E1)
D2-106 (#30) - D2-104 (E1)
D2-105 (#40) - D2-104 (E1)
Y - BR
R - BR
G - BR
L - BR
Fuel injector Engine switch on (IG) 11 to 14 V
Idling Pulse generation
(see waveform 3)
D2-109 (HA1A) - D2-46 (E04) B - BR Air fuel ratio sensor heater Engine switch on (IG) 11 to 14 V
Idling Below 3.0 V
D2-112 (A1A+) - D2-104 (E1) B - BR Air fuel ratio sensor Idling 3 to 3.6 V*1
D2-113 (A1A-) - D2-104 (E1) W - BR Air fuel ratio sensor Idling 2.7 to 3.3 V*1
D2-47 (HT1B) - D2-86 (E03) R - BR Heated oxygen sensor heater Engine switch on (IG) 11 to 14 V
Idling Below 3.0 V
D2-64 (OX1B) - D2-87 (EX1B) W - Y Heated oxygen sensor Engine speed maintained at 2,500 rpm for 2 minutes after warming up engine Pulse generation
(see waveform 4)
D2-110 (KNK1) - D2-111 (EKNK) B - W Knock sensor Engine speed maintained at 4,000 after warming up engine Pulse generation
(see waveform 5)
A7-8 (SPD) - D2-104 (E1) B - BR Speed signal from combination meter Driving at 20 km/h (12 mph) Pulse generation
(see waveform 6)
D2-97 (THW) - D2-96 (ETHW) Y - B Engine coolant temperature sensor Idling, Engine coolant temperature 80°C (176°F) 0.2 to 1.0 V
D2-65 (THA) - D2-88 (ETHA) R - V Intake air temperature sensor Idling, Intake air temperature 20°C (68°F) 0.5 to 3.4 V
D2-118 (VG) - D2-116 (E2G) W - P Mass air flow meter Idling, Shift lever position P or N, A/C switch OFF 0.5 to 3.0 V
A7-24 (W) - D2-104 (E1) Y - BR MIL Engine switch on (IG) (MIL goes on) Below 1.5 V
Idling 11 to 14 V
A7-48 (STA) - D2-104 (E1) B - BR Starter signal Cranking 5.5 V or more
D2-115 (VTA1) - D2-91 (ETA) P - W Throttle position sensor (for engine control) Engine switch on (IG), Accelerator pedal fully released 0.5 to 1.1 V
Engine switch on (IG), Accelerator pedal fully depressed 3.2 to 4.8 V
D2-114 (VTA2) - D2-91 (ETA) G - W Throttle position sensor (for sensor malfunction detection) Engine switch on (IG), Accelerator pedal fully released 2.1 to 3.1 V
Engine switch on (IG), Accelerator pedal fully depressed 4.6 to 5.0 V
D2-67 (VCTA) - D2-91 (ETA) B - W Power source of sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
A7-57 (VCPA) - A7-59 (EPA) P - R Power source of accelerator pedal position sensor (for VPA) Engine switch on (IG) 4.5 to 5.5 V
A7-55 (VPA) - A7-59 (EPA) V - R Accelerator pedal position sensor (for engine control) Engine switch on (IG), Accelerator pedal fully released 0.5 to 1.1 V
Engine switch on (IG), Accelerator pedal fully depressed 2.6 to 4.5 V
A7-56 (VPA2) - A7-60 (EPA2) Y - BE Accelerator pedal position sensor (for sensor malfunctioning detection) Engine switch on (IG), Accelerator pedal fully released 1.2 to 2.0 V
Engine switch on (IG), Accelerator pedal fully depressed 3.4 to 4.75 V
A7-58 (VCP2) - A7-60 (EPA2) B - BE Power source of accelerator pedal position sensor (for VPA2) Engine switch on (IG) 4.5 to 5.5 V
D2-42 (M+) - D2-43 (ME01) R - BR Throttle actuator Idling with warm engine Pulse generation
(see waveform 8)
D2-41 (M-) - D2-43 (ME01) G - BR Throttle actuator Idling with warm engine Pulse generation
(see waveform 7)
A7-36 (STP) - D2-104 (E1) L - BR Stop light switch Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V
A7-35 (ST1-) - D2-104 (E1) V - BR Stop light switch Engine switch on (IG), Brake pedal depressed Below 1.5 V
Engine switch on (IG), Brake pedal released 7.5 to 14 V
D2-49 (PRG) - D2-104 (E1) B - BR Purge VSV Engine switch on (IG) 11 to 14 V
Idling, under purge control Pulse generation
(see waveform 9)
A7-7 (FC) - D2-104 (E1) L - BR Fuel pump control Engine switch on (IG) 11 to 14 V
Idling Below 1.5 V
A7-15 (TACH) - D2-104 (E1) B - BR Engine speed Idling Pulse generation
(see waveform 10)
A7-27 (TC) - D2-104 (E1) R - BR Terminal TC of DLC3 Engine switch on (IG) 11 to 14 V
D2-100 (OC1+) - D2-123 (OC1-) P - V Camshaft timing oil control valve (OCV) Idling Pulse generation
(see waveform 11)
A7-41 (CANH) - D2-104 (E1) B - BR CAN communication line Engine switch on (IG) Pulse generation
(see waveform 12)
A7-49 (CANL) - D2-104 (E1) W - BR CAN communication line Engine switch on (IG) Pulse generation
(see waveform 13)
A7-21 (FANL) - D2-104 (E1) R - BR FAN NO. 3 relay Engine switch on (IG) 11 to 14 V
Idling with A/C ON
or
High engine coolant temperature
Below 1.5 V
A7-22 (FANH) - D2-104 (E1) Y - BR FAN NO. 1, 2 relay Idling with high engine coolant temperature Below 1.5 V
D2-50 (ALT) - D2-104 (E1) B - BR Generator Engine switch on (IG) 11 to 14 V
A7-28 (IGSW) - D2-104 (E1) BE - BR Engine switch Engine switch on (IG) 11 to 14 V
A7-44 (MREL) - D2-104 (E1) Y - BR EFI MAIN relay Engine switch on (IG) 11 to 14 V
A7-13 (ACCR) - D2-104 (E1) GR - BR Accessory power cut signal Cranking Below 1.5 V
A7-14 (STSW) - D2-104 (E1) P - BR Engine cranking required signal Cranking 9 to 14 V
D2-52 (STAR) - D2-104 (E1) G*2, LG*3 - BR ST relay control Cranking 5.5 V or more
D2-69 (VCIB) - D2-92 (EIB) P - BR Power source of battery current sensor Engine switch on (IG) 4.5 to 5.0 V
D2-68 (IB) - D2-92 (EIB) W - BR Battery current sensor Engine switch on (IG) 0.5 to 4.5 V
D2-120 (THB) - D2-92 (EIB) B - BR Battery temperature sensor Engine switch on (IG) 0.5 to 4.5 V

*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

*2: for A/T models.

*3: for CVT models.


WAVEFORM 1


A395440E01
0.458,0.188 1.01,0.458 0.552,0.271 10 false 2 V/DIV. 0.802,0.635 1.354,0.906 0.552,0.271 10 false IGT 0.625,0.885 1.177,1.156 0.552,0.271 10 false GND 1.75,1.844 2.99,2.083 1.24,0.24 10 false 20 msec./DIV. 0.833,1.198 1.385,1.469 0.552,0.271 10 false IGF1 0.625,1.469 1.177,1.74 0.552,0.271 10 false GND

Igniter IGT signal (from ECM to igniter)
Terminal No. (Symbols) D2-85 (IGT1) - D2-104 (E1)
D2-84 (IGT2) - D2-104 (E1)
D2-83 (IGT3) - D2-104 (E1)
D2-82 (IGT4) - D2-104 (E1)
D2-81 (IGF1) - D2-104 (E1)
Tool Setting 2 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 2


A063955E86
2.802,0.573 3.125,0.75 0.323,0.177 10 false GND 2.802,1.375 3.125,1.552 0.323,0.177 10 false GND 0.167,0.49 0.458,0.667 0.292,0.177 10 false CH1 0.094,0.667 0.49,0.844 0.396,0.177 10 false (G2+) 0.167,1.281 0.458,1.458 0.292,0.177 10 false CH2 0.094,1.458 0.479,1.635 0.385,0.177 10 false (NE+) 1.063,1.896 1.948,2.073 0.885,0.177 10 false 20 msec./DIV. 2.75,0.031 3.281,0.208 0.531,0.177 10 false 5 V/DIV.

Crankshaft position sensor and Camshaft position sensor
Terminal No. (Symbols) CH1: D2-99 (G2+) - D2-98 (G2-)
CH2: D2-122 (NE+) - D2-121 (NE-)
Tool Setting 5 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 3


A378740E01
0.51,0.208 1.271,0.531 0.76,0.323 10 false 20 V/DIV. 0.594,1.583 1.125,1.875 0.531,0.292 10 false GND 1.771,1.896 2.844,2.115 1.073,0.219 10 false 20 msec./DIV.

No. 1 (to No. 4) fuel injector signal
Terminal No. (Symbols) D2-108 (#10) - D2-104 (E1)
D2-107 (#20) - D2-104 (E1)
D2-106 (#30) - D2-104 (E1)
D2-105 (#40) - D2-104 (E1)
Tool Setting 20 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 4


U113545E10
0.396,0.188 1.063,0.406 0.667,0.219 10 false 0.2 V/DIV. 0.552,1.479 0.917,1.677 0.365,0.198 10 false GND 1.74,1.875 3.427,2.177 1.688,0.302 10 true 200 ms./DIV.

Heated oxygen sensor (bank 1 sensor 2)
Terminal No. (Symbols) D2-64 (OX1B) - D2-87 (EX1B)
Tool Setting 0.2 V/DIV., 200 msec./DIV.
Condition Engine speed maintained at 2,500 rpm for 2 minutes after warming up engine

HINT:

In the Data List, the items O2S B1S2 show the ECM input values of the heated oxygen sensor.



WAVEFORM 5


A395157E01
2.583,0.135 3.104,0.302 0.521,0.167 10 false 1 V/DIV. 2.802,0.969 3.177,1.146 0.375,0.177 10 false GND 1.615,1.677 2.49,1.885 0.875,0.208 10 false 1 msec./DIV.

Knock sensor
Terminal No. (Symbols) D2-110 (KNK1) - D2-111 (EKNK)
Tool Setting 1 V/DIV., 1 msec./DIV.
Condition Engine speed maintained at 4,000 after warming up engine

HINT:
·

The wavelength becomes shorter as engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle.




WAVEFORM 6


A395159E01
1.156,2 2.094,2.177 0.938,0.177 10 false 20 msec./DIV. 2.823,1.229 3.156,1.427 0.333,0.198 10 false GND 2.688,0.125 3.271,0.323 0.583,0.198 10 false 5 V/DIV.

Vehicle speed signal
Terminal No. (Symbols) A7-8 (SPD) - D2-104 (E1)
Tool Setting 5 V/DIV., 20 msec./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 7


A245848E54
2.849,0.99 3.182,1.142 0.333,0.151 10 GND 2.627,0.266 3.166,0.409 0.539,0.142 10 5 V/DIV. 0.479,0.626 0.664,0.777 0.184,0.15 10 M- 1.323,1.82 1.996,1.967 0.672,0.147 10 1 ms./DIV.

Throttle actuator negative terminal
Terminal No. (Symbols) D2-41 (M-) - D2-43 (ME01)
Tool Setting 5 V/DIV., 1 msec./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 8


A208000E60
2.856,0.973 3.187,1.119 0.331,0.147 10 GND 2.631,0.216 3.176,0.36 0.545,0.144 10 5 V/DIV. 0.501,0.616 0.722,0.759 0.221,0.143 10 M+ 1.323,1.806 1.995,1.965 0.672,0.159 10 1 ms./DIV.

Throttle actuator positive terminal
Terminal No. (Symbols) D2-42 (M+) - D2-43 (ME01)
Tool Setting 5 V/DIV., 1 msec./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 9


A218020E25
2.676,0.174 3.296,0.318 0.62,0.145 10 10 V/DIV. 2.806,0.925 3.143,1.065 0.337,0.14 10 GND 1.189,1.789 1.937,1.936 0.749,0.147 10 20 ms./DIV.

Purge VSV
Terminal No. (Symbols) D2-49 (PRG) - D2-104 (E1)
Tool Setting 10 V/DIV., 20 msec./DIV.
Condition Idling, under purge control

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 10


A395164E01
1.615,1.781 2.563,1.969 0.948,0.188 10 false 10 msec./DIV. 2.875,1.229 3.219,1.417 0.344,0.188 10 false GND 2.729,0.073 3.302,0.24 0.573,0.167 10 false 5 V/DIV.

Engine speed signal
Terminal No. (Symbols) A7-15 (TACH) - D2-104 (E1)
Tool Setting 5 V/DIV., 10 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 11


U188238E02
0.448,0.167 1.021,0.365 0.573,0.198 10 false 5 V/DIV. 0.573,1.115 0.938,1.313 0.365,0.198 10 false GND 1.75,1.854 2.646,2.052 0.896,0.198 10 false 1 msec./DIV.

Camshaft timing oil control valve (OCV)
Terminal No. (Symbols) D2-100 (OC1+) - D2-123 (OC1-)
Tool Setting 5 V/DIV., 1 msec./DIV.
Condition Idling


WAVEFORM 12


A395294E01
2.802,0.229 3.354,0.438 0.552,0.208 10 false 1 V/DIV. 3.021,1.406 3.365,1.594 0.344,0.188 10 false GND 1.573,1.917 2.51,2.135 0.938,0.219 10 false 10 μsec./DIV.

CAN communication signal
Terminal No. (Symbols) A7-41 (CANH) - D2-104 (E1)
Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 13


A395165E01
2.792,0.167 3.354,0.333 0.563,0.167 10 false 1 V/DIV. 2.906,1.531 3.26,1.698 0.354,0.167 10 false GND 1.604,1.885 2.49,2.073 0.885,0.188 10 false 10 μsec./DIV.

CAN communication signal
Terminal No. (Symbols) A7-49 (CANL) - D2-104 (E1)
Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.