The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A7-20 (BATT) - D2-104 (E1) | W - BR | Battery (for measuring battery voltage and for ECM memory) | Always | 11 to 14 V |
| A7-2 (+B) - D2-104 (E1) | B - BR | Power source of ECM | Engine switch on (IG) | 11 to 14 V |
| A7-1 (+B2) - D2-104 (E1) | B - BR | Power source of ECM | Engine switch on (IG) | 11 to 14 V |
| A7-3 (+BM) - D2-104 (E1) | R - BR | Power source of throttle actuator | Always | 11 to 14 V |
| D2-85 (IGT1) - D2-104 (E1)
D2-84 (IGT2) - D2-104 (E1) D2-83 (IGT3) - D2-104 (E1) D2-82 (IGT4) - D2-104 (E1) |
W - BR
Y - BR G - BR G - BR |
Ignition coil
(ignition signal) |
Idling | Pulse generation
(see waveform 1) |
| D2-81 (IGF1) - D2-104 (E1) | R - BR | Ignition coil
(ignition confirmation signal) |
Engine switch on (IG) | 4.5 to 5.5 V |
| Idling | Pulse generation
(see waveform 1) |
|||
| D2-122 (NE+) - D2-121 (NE-) | R - G | Crankshaft position sensor | Idling | Pulse generation
(see waveform 2) |
| D2-99 (G2+) - D2-98 (G2-) | L - Y | Camshaft position sensor | Idling | Pulse generation
(see waveform 2) |
| D2-108 (#10) - D2-104 (E1)
D2-107 (#20) - D2-104 (E1) D2-106 (#30) - D2-104 (E1) D2-105 (#40) - D2-104 (E1) |
Y - BR
R - BR G - BR L - BR |
Fuel injector | Engine switch on (IG) | 11 to 14 V |
| Idling | Pulse generation
(see waveform 3) |
|||
| D2-109 (HA1A) - D2-46 (E04) | B - BR | Air fuel ratio sensor heater | Engine switch on (IG) | 11 to 14 V |
| Idling | Below 3.0 V | |||
| D2-112 (A1A+) - D2-104 (E1) | B - BR | Air fuel ratio sensor | Idling | 3 to 3.6 V*1 |
| D2-113 (A1A-) - D2-104 (E1) | W - BR | Air fuel ratio sensor | Idling | 2.7 to 3.3 V*1 |
| D2-47 (HT1B) - D2-86 (E03) | R - BR | Heated oxygen sensor heater | Engine switch on (IG) | 11 to 14 V |
| Idling | Below 3.0 V | |||
| D2-64 (OX1B) - D2-87 (EX1B) | W - Y | Heated oxygen sensor | Engine speed maintained at 2,500 rpm for 2 minutes after warming up engine | Pulse generation
(see waveform 4) |
| D2-110 (KNK1) - D2-111 (EKNK) | B - W | Knock sensor | Engine speed maintained at 4,000 after warming up engine | Pulse generation
(see waveform 5) |
| A7-8 (SPD) - D2-104 (E1) | B - BR | Speed signal from combination meter | Driving at 20 km/h (12 mph) | Pulse generation
(see waveform 6) |
| D2-97 (THW) - D2-96 (ETHW) | Y - B | Engine coolant temperature sensor | Idling, Engine coolant temperature 80°C (176°F) | 0.2 to 1.0 V |
| D2-65 (THA) - D2-88 (ETHA) | R - V | Intake air temperature sensor | Idling, Intake air temperature 20°C (68°F) | 0.5 to 3.4 V |
| D2-118 (VG) - D2-116 (E2G) | W - P | Mass air flow meter | Idling, Shift lever position P or N, A/C switch OFF | 0.5 to 3.0 V |
| A7-24 (W) - D2-104 (E1) | Y - BR | MIL | Engine switch on (IG) (MIL goes on) | Below 1.5 V |
| Idling | 11 to 14 V | |||
| A7-48 (STA) - D2-104 (E1) | B - BR | Starter signal | Cranking | 5.5 V or more |
| D2-115 (VTA1) - D2-91 (ETA) | P - W | Throttle position sensor (for engine control) | Engine switch on (IG), Accelerator pedal fully released | 0.5 to 1.1 V |
| Engine switch on (IG), Accelerator pedal fully depressed | 3.2 to 4.8 V | |||
| D2-114 (VTA2) - D2-91 (ETA) | G - W | Throttle position sensor (for sensor malfunction detection) | Engine switch on (IG), Accelerator pedal fully released | 2.1 to 3.1 V |
| Engine switch on (IG), Accelerator pedal fully depressed | 4.6 to 5.0 V | |||
| D2-67 (VCTA) - D2-91 (ETA) | B - W | Power source of sensor (specific voltage) | Engine switch on (IG) | 4.5 to 5.5 V |
| A7-57 (VCPA) - A7-59 (EPA) | P - R | Power source of accelerator pedal position sensor (for VPA) | Engine switch on (IG) | 4.5 to 5.5 V |
| A7-55 (VPA) - A7-59 (EPA) | V - R | Accelerator pedal position sensor (for engine control) | Engine switch on (IG), Accelerator pedal fully released | 0.5 to 1.1 V |
| Engine switch on (IG), Accelerator pedal fully depressed | 2.6 to 4.5 V | |||
| A7-56 (VPA2) - A7-60 (EPA2) | Y - BE | Accelerator pedal position sensor (for sensor malfunctioning detection) | Engine switch on (IG), Accelerator pedal fully released | 1.2 to 2.0 V |
| Engine switch on (IG), Accelerator pedal fully depressed | 3.4 to 4.75 V | |||
| A7-58 (VCP2) - A7-60 (EPA2) | B - BE | Power source of accelerator pedal position sensor (for VPA2) | Engine switch on (IG) | 4.5 to 5.5 V |
| D2-42 (M+) - D2-43 (ME01) | R - BR | Throttle actuator | Idling with warm engine | Pulse generation
(see waveform 8) |
| D2-41 (M-) - D2-43 (ME01) | G - BR | Throttle actuator | Idling with warm engine | Pulse generation
(see waveform 7) |
| A7-36 (STP) - D2-104 (E1) | L - BR | Stop light switch | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | Below 1.5 V | |||
| A7-35 (ST1-) - D2-104 (E1) | V - BR | Stop light switch | Engine switch on (IG), Brake pedal depressed | Below 1.5 V |
| Engine switch on (IG), Brake pedal released | 7.5 to 14 V | |||
| D2-49 (PRG) - D2-104 (E1) | B - BR | Purge VSV | Engine switch on (IG) | 11 to 14 V |
| Idling, under purge control | Pulse generation
(see waveform 9) |
|||
| A7-7 (FC) - D2-104 (E1) | L - BR | Fuel pump control | Engine switch on (IG) | 11 to 14 V |
| Idling | Below 1.5 V | |||
| A7-15 (TACH) - D2-104 (E1) | B - BR | Engine speed | Idling | Pulse generation
(see waveform 10) |
| A7-27 (TC) - D2-104 (E1) | R - BR | Terminal TC of DLC3 | Engine switch on (IG) | 11 to 14 V |
| D2-100 (OC1+) - D2-123 (OC1-) | P - V | Camshaft timing oil control valve (OCV) | Idling | Pulse generation
(see waveform 11) |
| A7-41 (CANH) - D2-104 (E1) | B - BR | CAN communication line | Engine switch on (IG) | Pulse generation
(see waveform 12) |
| A7-49 (CANL) - D2-104 (E1) | W - BR | CAN communication line | Engine switch on (IG) | Pulse generation
(see waveform 13) |
| A7-21 (FANL) - D2-104 (E1) | R - BR | FAN NO. 3 relay | Engine switch on (IG) | 11 to 14 V |
| Idling with A/C ON
or High engine coolant temperature |
Below 1.5 V | |||
| A7-22 (FANH) - D2-104 (E1) | Y - BR | FAN NO. 1, 2 relay | Idling with high engine coolant temperature | Below 1.5 V |
| D2-50 (ALT) - D2-104 (E1) | B - BR | Generator | Engine switch on (IG) | 11 to 14 V |
| A7-28 (IGSW) - D2-104 (E1) | BE - BR | Engine switch | Engine switch on (IG) | 11 to 14 V |
| A7-44 (MREL) - D2-104 (E1) | Y - BR | EFI MAIN relay | Engine switch on (IG) | 11 to 14 V |
| A7-13 (ACCR) - D2-104 (E1) | GR - BR | Accessory power cut signal | Cranking | Below 1.5 V |
| A7-14 (STSW) - D2-104 (E1) | P - BR | Engine cranking required signal | Cranking | 9 to 14 V |
| D2-52 (STAR) - D2-104 (E1) | G*2, LG*3 - BR | ST relay control | Cranking | 5.5 V or more |
| D2-69 (VCIB) - D2-92 (EIB) | P - BR | Power source of battery current sensor | Engine switch on (IG) | 4.5 to 5.0 V |
| D2-68 (IB) - D2-92 (EIB) | W - BR | Battery current sensor | Engine switch on (IG) | 0.5 to 4.5 V |
| D2-120 (THB) - D2-92 (EIB) | B - BR | Battery temperature sensor | Engine switch on (IG) | 0.5 to 4.5 V |
*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.
*2: for A/T models.
*3: for CVT models.
WAVEFORM 1
| Terminal No. (Symbols) | D2-85 (IGT1) - D2-104 (E1)
D2-84 (IGT2) - D2-104 (E1) D2-83 (IGT3) - D2-104 (E1) D2-82 (IGT4) - D2-104 (E1) D2-81 (IGF1) - D2-104 (E1) |
| Tool Setting | 2 V/DIV., 20 msec./DIV. |
| Condition | Idling |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 2
| Terminal No. (Symbols) | CH1: D2-99 (G2+) - D2-98 (G2-)
CH2: D2-122 (NE+) - D2-121 (NE-) |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | Idling |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 3
| Terminal No. (Symbols) | D2-108 (#10) - D2-104 (E1)
D2-107 (#20) - D2-104 (E1) D2-106 (#30) - D2-104 (E1) D2-105 (#40) - D2-104 (E1) |
| Tool Setting | 20 V/DIV., 20 msec./DIV. |
| Condition | Idling |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 4
| Terminal No. (Symbols) | D2-64 (OX1B) - D2-87 (EX1B) |
| Tool Setting | 0.2 V/DIV., 200 msec./DIV. |
| Condition | Engine speed maintained at 2,500 rpm for 2 minutes after warming up engine |
In the Data List, the items O2S B1S2 show the ECM input values of the heated oxygen sensor.
WAVEFORM 5
| Terminal No. (Symbols) | D2-110 (KNK1) - D2-111 (EKNK) |
| Tool Setting | 1 V/DIV., 1 msec./DIV. |
| Condition | Engine speed maintained at 4,000 after warming up engine |
The wavelength becomes shorter as engine speed increases.
The waveforms and amplitudes displayed differ slightly depending on the vehicle.
WAVEFORM 6
| Terminal No. (Symbols) | A7-8 (SPD) - D2-104 (E1) |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | Driving at 20 km/h (12 mph) |
The wavelength becomes shorter as the vehicle speed increases.
WAVEFORM 7
| Terminal No. (Symbols) | D2-41 (M-) - D2-43 (ME01) |
| Tool Setting | 5 V/DIV., 1 msec./DIV. |
| Condition | Idling with warm engine |
The duty ratio varies depending on the throttle actuator operation.
WAVEFORM 8
| Terminal No. (Symbols) | D2-42 (M+) - D2-43 (ME01) |
| Tool Setting | 5 V/DIV., 1 msec./DIV. |
| Condition | Idling with warm engine |
The duty ratio varies depending on the throttle actuator operation.
WAVEFORM 9
| Terminal No. (Symbols) | D2-49 (PRG) - D2-104 (E1) |
| Tool Setting | 10 V/DIV., 20 msec./DIV. |
| Condition | Idling, under purge control |
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.
WAVEFORM 10
| Terminal No. (Symbols) | A7-15 (TACH) - D2-104 (E1) |
| Tool Setting | 5 V/DIV., 10 msec./DIV. |
| Condition | Idling |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 11
| Terminal No. (Symbols) | D2-100 (OC1+) - D2-123 (OC1-) |
| Tool Setting | 5 V/DIV., 1 msec./DIV. |
| Condition | Idling |
WAVEFORM 12
| Terminal No. (Symbols) | A7-41 (CANH) - D2-104 (E1) |
| Tool Setting | 1 V/DIV., 10 μsec./DIV. |
| Condition | Engine switch on (IG) |
The waveform varies depending on the CAN communication signal.
WAVEFORM 13
| Terminal No. (Symbols) | A7-49 (CANL) - D2-104 (E1) |
| Tool Setting | 1 V/DIV., 10 μsec./DIV. |
| Condition | Engine switch on (IG) |
The waveform varies depending on the CAN communication signal.