These DTCs indicate malfunctions relating to the primary circuit.
If DTC P0351 is output, check the ignition coil (No. 1 cylinder) circuit.
If DTC P0352 is output, check the ignition coil (No. 2 cylinder) circuit.
If DTC P0353 is output, check the ignition coil (No. 3 cylinder) circuit.
If DTC P0354 is output, check the ignition coil (No. 4 cylinder) circuit.
A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0351
P0352 P0353 P0354 |
No IGF signal to ECM while engine running
(1 trip detection logic) |
·
Ignition system ·
Open or short in IGF1 or IGT circuit (1 to 4) between ignition coil and ECM ·
No. 1 to No. 4 ignition coils ·
ECM |
Reference: Inspection using an oscilloscope.
While idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.
| Item | Content |
|---|---|
| Terminals | CH1:
D2-85 (IGT1) - D2-104 (E1) D2-84 (IGT2) - D2-104 (E1) D2-83 (IGT3) - D2-104 (E1) D2-82 (IGT4) - D2-104 (E1) CH2: D2-81 (IGF1) - D2-104 (E1) |
| Equipment Settings | 2 V/DIV.
20 msec./DIV. |
| Conditions | Idling |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Disconnect the ignition coil connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D26-4 (GND) - Body ground | Always | Below 1 Ω |
| D27-4 (GND) - Body ground | Always | Below 1 Ω |
| D28-4 (GND) - Body ground | Always | Below 1 Ω |
| D29-4 (GND) - Body ground | Always | Below 1 Ω |
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D26-1 (+B) - D26-4 (GND) | Engine switch on (IG) | 11 to 14 V |
| D27-1 (+B) - D27-4 (GND) | Engine switch on (IG) | 11 to 14 V |
| D28-1 (+B) - D28-4 (GND) | Engine switch on (IG) | 11 to 14 V |
| D29-1 (+B) - D29-4 (GND) | Engine switch on (IG) | 11 to 14 V |
OK
NG
Disconnect the ignition coil connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D26-2 (IGF) - D2-81 (IGF1) | Always | Below 1 Ω |
| D27-2 (IGF) - D2-81 (IGF1) | Always | Below 1 Ω |
| D28-2 (IGF) - D2-81 (IGF1) | Always | Below 1 Ω |
| D29-2 (IGF) - D2-81 (IGF1) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D26-3 (IGT1) - D2-85 (IGT1) | Always | Below 1 Ω |
| D27-3 (IGT2) - D2-84 (IGT2) | Always | Below 1 Ω |
| D28-3 (IGT3) - D2-83 (IGT3) | Always | Below 1 Ω |
| D29-3 (IGT4) - D2-82 (IGT4) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D26-2 (IGF) or D2-81 (IGF1) - Body ground | Always | 10 kΩ or higher |
| D27-2 (IGF) or D2-81 (IGF1) - Body ground | Always | 10 kΩ or higher |
| D28-2 (IGF) or D2-81 (IGF1) - Body ground | Always | 10 kΩ or higher |
| D29-2 (IGF) or D2-81 (IGF1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D26-3 (IGT1) or D2-85 (IGT1) - Body ground | Always | 10 kΩ or higher |
| D27-3 (IGT2) or D2-84 (IGT2) - Body ground | Always | 10 kΩ or higher |
| D28-3 (IGT3) or D2-83 (IGT3) - Body ground | Always | 10 kΩ or higher |
| D29-3 (IGT4) or D2-82 (IGT4) - Body ground | Always | 10 kΩ or higher |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and wait for at least 30 seconds.
Shuffle arrangement of the ignition coils (among No. 1 to No. 4 cylinders).
Do not shuffle the connectors.
Perform a simulation test.
Check DTCs displayed on the GTS.
| Result | Proceed to |
|---|---|
| Same DTC output | A |
| Different ignition coil DTC output | B |
A
B