Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0443  Evaporative Emission Control System Purge Control Valve Circuit  


DESCRIPTION

To reduce hydrocarbon (HC) emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signals to the purge VSV so that the intake amount of hydrocarbon (HC) emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. DTC Detection Condition Trouble Area
P0443 Both of the following conditions (a) and (b) are met (1 trip detection logic):
(a) The target control value and actual control value do not match for 10 seconds or more.
(b) The target control value and actual control value do not match for 80 times or more.
·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM



WIRING DIAGRAM

A235721E05
6.063,2.125 6.385,2.271 0.323,0.146 10 false ECM 5.49,0.865 5.656,1.042 0.167,0.177 10 false 49 5.771,1.021 6.094,1.198 0.323,0.177 10 false PRG 5.781,1.563 6.188,1.74 0.406,0.177 10 false MREL 5.5,1.042 5.771,1.219 0.271,0.177 10 false D2 5.5,1.552 5.76,1.729 0.26,0.177 10 false A7 3.938,1.333 4.26,1.479 0.323,0.146 10 false D50 4.271,1.333 5,1.552 0.729,0.219 10 false Purge VSV 2.135,1.917 2.76,2.063 0.625,0.146 10 false EFI MAIN 1.281,1.177 1.552,1.354 0.271,0.177 10 false EFI 0.698,1.406 1.365,1.583 0.667,0.177 10 false F/B BATT 0.688,2.406 1.354,2.583 0.667,0.177 10 false FL MAIN 0.854,3.823 1.313,4 0.458,0.177 10 false Battery 5.5,1.375 5.667,1.552 0.167,0.177 10 false 44 4.792,0.927 4.948,1.104 0.156,0.177 10 false 2 4.031,0.917 4.188,1.094 0.156,0.177 10 false 1 2.76,0.927 2.917,1.104 0.156,0.177 10 false 3 2.021,0.927 2.177,1.104 0.156,0.177 10 false 5 2.76,1.438 2.917,1.615 0.156,0.177 10 false 1 2.021,1.438 2.177,1.615 0.156,0.177 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE PURGE VSV CONTROL)
a.
A200511E01
0.55,0.157 1.109,0.306 0.559,0.149 10 VSV ON 2.222,0.157 2.843,0.306 0.621,0.149 10 VSV OFF 0.593,1.471 1.152,1.627 0.559,0.156 10 Air flows 1.985,1.471 3.058,1.627 1.073,0.156 10 Air does not flow

Connect the intelligent tester to the DLC3.


b.

Remove the purge hose (on the canister side) of the purge hose.


c.

Start the engine and turn the tester ON.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.


e.

When the purge VSV is operated using the intelligent tester, check whether the port of the purge VSV applies suction to your finger.

OK:
Tester Operation Specified Condition
VSV is ON Applies suction to finger
VSV is OFF Applies no suction to finger




NG

2.INSPECT PURGE VSV

OK

2.INSPECT PURGE VSV

OK

3.INSPECT PURGE VSV (POWER SOURCE VOLTAGE)

NG

3.INSPECT PURGE VSV (POWER SOURCE VOLTAGE)
U188262E02
1.333,1.708 2.052,1.906 0.719,0.198 10 false Front View 0.802,0.5 2.24,0.698 1.438,0.198 10 false Purge VSV Connector 0.052,0.073 1.417,0.271 1.365,0.198 10 false Wire Harness Side 0.823,1.229 1.094,1.406 0.271,0.177 10 false D50

a.

Disconnect the purge VSV connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D50-1 - Body ground Engine switch on (IG) 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI MAIN RELAY - PURGE VSV)

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the purge VSV connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D50-2 - D2-49 (PRG) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D50-2 or D2-49 (PRG) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR