Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0110  Intake Air Temperature Circuit  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

A393963E01
1.708,2.135 2.052,1.802 false 0.156,0.104 1.177,0.448 1.021,0.344 10 false Fig. 1 0.156,0.438 1.177,0.781 1.021,0.344 10 false Resistance 0.052,0.823 1.073,1.167 1.021,0.344 10 false (kΩ) 1.365,4.229 2.385,4.573 1.021,0.344 10 false Temperature 2.938,4.219 3.25,4.438 0.313,0.219 10 false (°C) 1.906,1.625 2.833,1.938 0.927,0.313 10 false Acceptable 2.948,4.385 3.26,4.604 0.313,0.219 10 false (°F)

The Intake Air Temperature (IAT) sensor, mounted on the Mass Air Flow (MAF) meter, monitors the IAT. The IAT sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the IAT is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (see Fig. 1).

The IAT sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.

Resistor R and the IAT sensor are connected in series. When the resistance value of the IAT sensor changes, the voltage at terminal THA varies accordingly. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

HINT:

When any of DTCs P0110, P0112 and/or P0113 are stored, the ECM enters fail-safe mode. During fail-safe mode, the IAT is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.



DTC No. DTC Detection Condition Trouble Area
P0110 Open or short in IAT sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open or short in IAT sensor circuit

·

IAT sensor (built into MAF meter)

·

ECM


P0112 Short in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
·

Short in IAT sensor circuit

·

IAT sensor (built into MAF meter)

·

ECM


P0113 Open in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
·

Open in IAT sensor circuit

·

IAT sensor (built into MAF meter)

·

ECM



HINT:

When any of these DTCs are set, check the IAT by selecting the following menu items on the GTS: Powertrain / Engine and ECT / Data List / Intake Air.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit


WIRING DIAGRAM

A112566E33
0.355,0.356 2.456,0.537 2.101,0.181 10 IAT Sensor (Built into MAF Meter) 0.355,0.165 0.586,0.346 0.230,0.181 10 D3 5.801,0.11 6.031,0.292 0.230,0.181 10 D2 2.037,0.951 2.332,1.132 0.295,0.181 10 THA 2.146,1.532 2.333,1.714 0.187,0.181 10 E2 6.058,0.11 6.383,0.292 0.326,0.181 10 ECM 6.244,0.507 6.469,0.688 0.225,0.181 10 5 V 5.545,0.916 5.840,1.097 0.295,0.181 10 THA 5.545,1.524 5.933,1.706 0.388,0.181 10 ETHA 5.272,0.916 5.456,1.097 0.184,0.181 10 65 5.272,1.524 5.469,1.706 0.197,0.181 10 88 2.464,0.916 2.648,1.097 0.184,0.181 10 1 2.464,1.524 2.661,1.706 0.197,0.181 10 2 6.157,0.825 6.313,1.006 0.156,0.181 10 R

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


d.

Read the value displayed on the GTS.

OK:

Same as actual Intake Air Temperature (IAT).


Result
Temperature Displayed Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
Same as actual IAT C

HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or higher.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A394018E01
0.417,2.417 0.833,2.667 0.417,0.25 1.167,4.021 1.323,3.448 false 1.865,4.042 1.542,3.479 false 0.313,0.25 1.104,0.49 0.792,0.24 10 false MAF Meter 2.531,0.26 3.146,0.49 0.615,0.229 10 false ECM 2.469,1.031 3.083,1.26 0.615,0.229 10 false THA 2.458,1.5 3.073,1.729 0.615,0.229 10 false ETHA 0.271,1.781 1.552,2.042 1.281,0.26 10 false Wire Harness Side 0.531,2.458 1.146,2.688 0.615,0.229 10 false D3 0.927,2.448 2.698,2.74 1.771,0.292 10 false MAF Meter Connector 1.833,4.083 2.448,4.313 0.615,0.229 10 false E2 2.417,3.917 3.25,4.135 0.833,0.219 10 false Front View 0.979,4.042 1.594,4.271 0.615,0.229 10 false THA

Disconnect the Mass Air Flow (MAF) meter connector.


b.

Connect terminals THA and E2 of the MAF meter wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


f.

Read the value displayed on the GTS.

Standard:

140°C (284°F) or higher




NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

OK

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the MAF meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D3-1 (THA) - D2-65 (THA) Always Below 1 Ω
D3-2 (E2) - D2-88 (ETHA) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A395375E01
0.417,0.323 1.167,0.49 0.75,0.167 10 false MAF Meter 2.531,0.219 2.885,0.406 0.354,0.188 10 false ECM 2.542,1.052 2.865,1.25 0.323,0.198 10 false THA 2.521,1.521 2.938,1.719 0.417,0.198 10 false ETHA

Disconnect the MAF meter connector.


b.

Connect an GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


e.

Read the value displayed on the GTS.

Standard:

-40°C (-40°F)




NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

OK

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the MAF meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D3-1 (THA) or D2-65 (THA) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR