Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.



DTC No. DTC Detection Condition Trouble Area
P0504 Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic):
(a) Engine switch on (IG)
(b) STP signal off when ST1- signal off
·

Open or short in stop light switch signal circuit

·

Stop light switch

·

ECM



WIRING DIAGRAM

A384969E02
0.385,3.844 1.438,4.135 1.052,0.292 10 false FL MAIN 0.573,4.542 1.625,4.833 1.052,0.292 10 false Battery 0.625,3.542 1.677,3.833 1.052,0.292 10 false ALT 2,3.531 3.052,3.823 1.052,0.292 10 false STOP 0.385,2.094 1.438,2.385 1.052,0.292 10 false IG2 1.708,1.385 2.76,1.677 1.052,0.292 10 false IG2 2.208,0.656 3.26,0.948 1.052,0.292 10 false 3 1.417,0.646 2.469,0.938 1.052,0.292 10 false 5 1.417,0.99 2.469,1.281 1.052,0.292 10 false 2 2.188,0.99 3.24,1.281 1.052,0.292 10 false 1 2.875,0.896 3.927,1.188 1.052,0.292 10 false IGN 3.885,2.448 4.938,2.74 1.052,0.292 10 false A37 4.24,2.448 5.375,3.031 1.135,0.583 10 false Stop Light Switch 4.156,1.167 5.208,1.458 1.052,0.292 10 false 5 5.177,1.177 6.229,1.469 1.052,0.292 10 false 4 4.177,1.604 5.229,1.896 1.052,0.292 10 false 1 5.188,1.615 6.24,1.906 1.052,0.292 10 false 2 5.188,2.021 6.24,2.313 1.052,0.292 10 false 3 4.344,1.25 5.396,1.542 1.052,0.292 10 false B 4.344,1.708 5.396,2 1.052,0.292 10 false B 4.969,1.271 6.021,1.563 1.052,0.292 10 false L 4.781,1.719 5.833,2.01 1.052,0.292 10 false OUT 4.771,2.115 5.823,2.406 1.052,0.292 10 false GND 5.844,0.75 6.896,1.042 1.052,0.292 10 false A7 6.167,0.74 7.031,1.031 0.865,0.292 10 false IGSW 5.844,1.26 6.896,1.552 1.052,0.292 10 false A7 5.833,1.708 6.885,2 1.052,0.292 10 false A7 5.844,2.51 6.896,2.802 1.052,0.292 10 false D2 5.823,2.333 6.875,2.625 1.052,0.292 10 false 104 6.146,2.5 6.781,2.885 0.635,0.385 10 false E2 5.854,0.552 6.906,0.844 1.052,0.292 10 false 28 6.156,1.26 6.885,1.573 0.729,0.313 10 false ST1- 6.156,1.708 6.865,2.042 0.708,0.333 10 false STP 5.833,1.531 6.885,1.823 1.052,0.292 10 false 36 5.854,1.073 6.906,1.365 1.052,0.292 10 false 35 6.375,3.052 6.844,3.344 0.469,0.292 10 false ECM 3.969,3.833 6.115,4.229 2.146,0.396 10 false from Main Body ECU 0.406,2.76 1.458,3.052 1.052,0.292 10 false F/B BATT 1.083,3.542 2.135,3.833 1.052,0.292 10 false RH-MAIN-JB

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Stop light switch conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the engine switch on (IG).

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Stop Light Switch and ST1.

(e)

Check the Data List indication when the brake pedal is depressed and released.

Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF




PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH)
a.
U188513E01
0.586,1.924 0.859,2.080 0.272,0.156 10 A37 0.181,0.158 0.336,0.314 0.154,0.156 10 *a 1.326,2.354 1.038,2.979 false 0.943,2.985 1.070,3.140 0.127,0.156 10 B

Disconnect the stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-1 (B) - Body ground Always 11 to 14 V

Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch)




OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STOP LIGHT SWITCH)

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH)
a.
U188514E01
0.586,1.924 0.859,2.080 0.272,0.156 10 A37 0.181,0.158 0.336,0.314 0.154,0.156 10 *a 2.172,2.357 2.481,2.933 false 2.468,2.972 2.609,3.128 0.141,0.156 10 B

Disconnect the stop light switch connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-5 (B) - Body ground Engine switch on (IG) 11 to 14 V

Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch)




OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 RELAY - STOP LIGHT SWITCH)

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - BODY GROUND)
a.

Disconnect the stop light switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-3 (GND) - Body ground Always Below 1 Ω




OK

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)
a.
U188273E02
1.865,3.656 2.75,3.479 true 1.771,3.667 0.542,3.771 true 1.781,0.063 2.552,0.406 0.771,0.344 10 false Brake Pedal Released 0.229,0.063 1,0.385 0.771,0.323 10 false Brake Pedal Depressed 0.073,2.104 1.302,2.281 1.229,0.177 10 false Wire Harness Side 1.167,2.552 2.177,2.729 1.01,0.177 10 false ECM Connector 2.813,3.385 3.104,3.563 0.292,0.177 10 false STP 0.146,3.688 0.469,3.865 0.323,0.177 10 false ST1- 1.375,4.156 2.052,4.333 0.677,0.177 10 false Front View 0.417,2.719 0.625,2.896 0.208,0.177 10 false A7

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Operation Specified Condition
A7-35 (ST1-) - Body ground Released 7.5 to 14 V
Depressed 0 to 1.5 V
A7-36 (STP) - Body ground Released 0 to 1.5 V
Depressed 7.5 to 14 V




OK

NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
a.

Disconnect the stop light switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-4 (L) - A7-35 (ST1-) Always Below 1 Ω
A37-2 (OUT) - A7-36 (STP) Always Below 1 Ω
A37-4 (L) or A7-35 (ST1-) - Body ground Always 10 kΩ or higher
A37-2 (OUT) or A7-36 (STP) - Body ground Always 10 kΩ or higher




OK

REPLACE STOP LIGHT SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR