Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the ECM even when the engine switch is in the off position. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM will illuminate the MIL and stores the DTC.

DTC No. DTC Detection Condition Trouble Area
P0560 Open in ECM back-up power source circuit
(1 trip detection logic)
·

Open in back-up power source circuit

·

Battery

·

Battery terminals

·

EFI fuse

·

ECM



HINT:

If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partially cleared.


WIRING DIAGRAM

A193164E25
1.958,1.271 2.604,1.438 0.646,0.167 10 false F/B BATT 3.531,1.26 3.792,1.417 0.26,0.156 10 false EFI 1.156,2.313 1.625,2.458 0.469,0.146 10 false Battery 5.292,0.938 5.49,1.083 0.198,0.146 10 false 20 5.281,1.125 5.5,1.292 0.219,0.167 10 false A7 5.219,2.167 5.479,2.354 0.26,0.188 10 false 104 5.281,2.365 5.479,2.51 0.198,0.146 10 false D2 5.583,1.125 5.979,1.281 0.396,0.156 10 false BATT 5.583,2.375 5.771,2.521 0.188,0.146 10 false E1 5.896,3.229 6.26,3.375 0.365,0.146 10 false ECM 1.042,1.656 1.688,1.823 0.646,0.167 10 false FL MAIN

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATT TERMINAL VOLTAGE)
a.

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-20 (BATT) - Body ground Always 11 to 14 V




OK

2.INSPECT BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT BATTERY
a.

Check that the battery is not depleted.

OK:

Battery is not depleted.




OK

3.CHECK BATTERY TERMINAL

NG

CHARGE OR REPLACE BATTERY

3.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded




OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE BATTERY TERMINAL

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Turn the engine switch off and turn the GTS off.


f.

Turn the engine switch on (IG) and turn the GTS on.


g.

Wait 5 seconds or more.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the DTCs.

Result:
Result Proceed to
DTC P0560 is output A
DTC is Not output B




A

B