Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM U

2AZ-FE ENGINE CONTROL  SFI SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.


NOTICE:

In the table below, the values listed under Normal Condition are for reference only. Do not depend solely on these values when determining whether or not a part is faulty.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the engine switch on (IG) and turn the tester ON.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List.


f.

Check the values by referring to the table below.



for CVT Models
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed:
Min.: 0 km/h, Max.: 255 km/h
Actual vehicle speed Speed indicated on speedometer
Engine Speed Engine speed:
Min.: 0 rpm, Max.: 16383 rpm
670 to 770 rpm: Idling -
Calculate Load Calculated load by ECM:
Min.: 0%, Max.: 100%
·

28 to 34%: Idling

·

24 to 30%: Running without load at 2000 rpm


-
Vehicle Load Vehicle load:
Min.: 0%, Max.: 25700%
Actual vehicle load Load percentage in terms of maximum intake air flow amount
MAF Air flow rate from mass air flow meter:
Min.: 0 gm/sec, Max.: 655.35 gm/sec
2.1 to 3.1 gm/sec.: Idling
6.2 to 8.7 gm/sec.: 2000 rpm
If value is approximately 0.0 gm/sec:
·

Mass air flow meter power source circuit open

·

VG circuit open or shorted


If value is 271.0 gm/sec or more:
·

E2G circuit open


Atmosphere Pressure Atmospheric pressure:
Min.: 0 kPa, Max.: 255 kPa
Approximately 100 kPa: Engine switch on (IG) -
Coolant Temp Engine coolant temperature:
Min.: -40°C (-40°F), Max.: 140°C (284°F)
80 to 95°C
(176 to 203°F): After warming up
·

If -40°C (-40°F): sensor circuit open

·

If 140°C (284°F) or more: sensor circuit shorted


Intake Air Intake air temperature:
Min.: -40°C (-40°F), Max.: 140°C (284°F)
Equivalent to ambient air temperature
·

If -40°C (-40°F): sensor circuit open

·

If 140°C (284°F) or more: sensor circuit shorted


Engine Run Time Engine run time:
Min.: 0 s, Max.: 65535 s
Time since engine started -
Initial Engine Coolant Temp Engine coolant temperature at engine start:
Min.: -40°C (-40°F), Max.: 119.3°C (248°F)
Close to ambient air temperature -
Initial Intake Air Temp Intake air temperature at engine start:
Min.: -40°C (-40°F), Max.: 119.3°C (248°F)
Close to ambient air temperature -
Battery Voltage Battery voltage:
Min.: 0 V, Max.: 65.5 V
11 to 14 V: Engine switch on (IG) -
Glow Indicator Supported Status of glow indicator supported:
Supported or Unsupported
Unused -
Glow Indicator Status of glow indicator:
ON or OFF
Unused -
Accelerator Position Accelerator pedal position:
Min.: 0%, Max.: 399.9%
Actual accelerator pedal position -
Accel Sens. No. 1 Volt % Absolute accelerator pedal position No. 1:
Min.: 0%, Max.: 100%
10 to 22%: Accelerator pedal fully released
52 to 90%: Accelerator pedal fully depressed
-
Accel Sens. No. 2 Volt % Absolute accelerator pedal position No. 2:
Min.: 0%, Max.: 100%
24 to 40%: Accelerator pedal fully released
68 to 95%: Accelerator pedal fully depressed
-
Accel Sensor Out No. 1 Accelerator pedal position sensor No. 1 voltage:
Min.: 0 V, Max.: 4.98 V
0.5 to 1.1 V: Accelerator pedal fully released
2.6 to 4.5 V: Accelerator pedal fully depressed
-
Accel Sensor Out No. 2 Accelerator pedal position sensor No. 2 voltage:
Min.: 0 V, Max.: 4.98 V
1.2 to 2.0 V: Accelerator pedal fully released
3.4 to 4.75 V: Accelerator pedal fully depressed
-
Accelerator Idle Position Whether or not accelerator pedal position sensor detecting idle:
ON or OFF
ON: Idling -
Accel Fully Close Learn #1 Accelerator fully closed learning value No. 1:
Min.: 0 deg., Max.: 124.5 deg
- -
Accel Fully Close Learn #2 Accelerator fully closed learning value No. 2:
Min.: 0 deg., Max.: 124.5 deg
- -
Throttle Sensor Volt % Throttle valve opening percentage according to throttle position sensor:
Min.: 0%, Max.: 100%
·

10 to 22%: Accelerator pedal fully released

·

64 to 96%: Accelerator pedal fully depressed


Valve calculated based on the voltage at terminal VTA1
Throttl Sensor #2 Volt % Throttle valve opening percentage according to throttle position sensor No. 2:
Min.: 0 %, Max.: 100 %
·

42 to 62%: Accelerator pedal fully released

·

92 to 100%: Accelerator pedal fully depressed


Valve calculated based on the voltage at terminal VTA2
ST1 Brake pedal signal:
ON or OFF
ON: Brake pedal depressed -
System Guard System guard:
ON or OFF
- -
Open Side Malfunction Open side malfunction:
ON or OFF
- -
Throttle Idle Position Whether or not throttle position sensor detecting idling:
ON or OFF
·

ON: Accelerator pedal fully released

·

OFF: Accelerator pedal fully depressed


-
Throttle Require Position Required throttle position:
Min.: 0 V, Max.: 4.98 V
0.5 to 1.1 V: Idling -
Throttle Sensor Position*2 Throttle position sensor:
Min.: 0%, Max.: 100%
·

0%: Accelerator pedal fully released

·

50 to 80%: Accelerator pedal fully depressed


Recognition value for throttle opening angle on ECM
Throttle Position No. 1 Throttle position sensor No. 1 output voltage:
Min.: 0 V, Max.: 4.98 V
·

0.5 to 1.1 V: Accelerator pedal fully released

·

3.2 to 4.8 V: Accelerator pedal fully depressed

·

0.6 to 1.4 V: Fail-safe operating


-
Throttle Position No. 2 Throttle position sensor No. 2 output voltage:
Min.: 0 V, Max.: 4.98 V
·

2.1 to 3.1 V: Accelerator pedal fully released

·

4.6 to 4.98 V: Accelerator pedal fully depressed

·

2.1 to 3.1 V: Fail-safe operating


-
Throttle Position Command Throttle position command value:
Min.: 0 V, Max.: 4.98 V
- -
Throttle Sens Open Pos #1 Throttle sensor opener position No. 1:
Min.: 0 V, Max.: 4.98 V
0.6 to 1.4 V -
Throttle Sens Open Pos #2 Throttle sensor opener position No. 2:
Min.: 0 V, Max.: 4.98 V
1.7 to 2.5 V -
Throttle Motor Current Throttle actuator current:
Min.: 0 A, Max.: 19.9 A
0 to 3.0 A: Idling -
Throttle Motor DUTY Throttle actuator:
Min.: 0%, Max.: 100%
10 to 22%: Idling after engine warmed up -
Throttle Motor Duty (Open) Throttle actuator duty ratio (open):
Min.: 0 %, Max.: 255 %
0 to 40%: Idling -
Throttle Motor Duty (Close) Throttle actuator duty ratio (closed):
Min.: 0%, Max.: 255%
0 to 40%: Idling -
Throttle Fully Close Learn Throttle valve fully closed
(learned value):
Min.: 0 V, Max.: 4.98 V
0.4 to 1.0 V: Accelerator pedal fully released -
+BM Voltage +BM voltage:
Min.: 0, Max.: 79.99
11 to 14 (V): Engine switch on (IG) and system normal -
Actuator Power Supply Actuator power supply:
ON or OFF
ON: Idling -
Throttle Position Throttle valve opening angle:
Min.: 0 deg, Max.: 499.99 deg
- When the engine stalls, is difficult to start, or idles roughly
ISC Flow Flow rate calculated from information from each sensor:
Min.: 0 L/s, Max.: 79.99 L/s
- When the engine stalls, is difficult to start, or idles roughly
ISC Position Target valve opening angle calculated from ISC control:
Min.: 0 deg, Max.: 499.99 deg
- When the engine stalls, is difficult to start, or idles roughly
ISC Feedback Value ISC feedback value:
Min.: -40 L/s, Max.: 39.99 L/s
- When the engine stalls, is difficult to start, or idles roughly
ISC Learning Value ISC learning value:
Min.: -40 L/s, Max.: 39.99 L/s
- When the engine stalls, is difficult to start, or idles roughly
Electric Load Feedback Val Electrical load feedback value:
Min.: -40 L/s, Max.: 39.99 L/s
- When the engine stalls, is difficult to start, or idles roughly
Air Conditioner FB Val Air conditioner load feedback value:
Min.: -40 L/s, Max.: 39.99 L/s
- When the engine stalls, is difficult to start, or idles roughly
PS Feedback Val Power steering load feedback value:
Min.: -40 L/s, Max.: 39.99 L/s
- When the engine stalls, is difficult to start, or idles roughly
Low Revolution Control Status of low engine speed control:
ON or OFF
- When the engine stalls, is difficult to start, or idles roughly
Neutral Control Neutral position control status for automatic transaxle:
ON or OFF
- When the engine stalls, is difficult to start, or idles roughly
N Range Status Judgement for shift lever neutral position:
ON or OFF
- When the engine stalls, is difficult to start, or idles roughly
Eng Stall Control FB Flow Feedback value of intake air flow:
Min.: -40 L/s, Max.: 39.99 L/s
- When the engine stalls, is difficult to start, or idles roughly
Deposit Loss Flow Deposit loss air flow rate:
Min.: -40 L/s, Max.: 39.99 L/s
0 to 6.0 L/s
·

This value indicates the amount of compensation for a decrease in flow passage area due to the buildup of deposits on the throttle valve.

·

Check this value for reference when the engine stalls, is difficult to start, or idles roughly.

·

When the ISC learned value is initialized by disconnecting the battery negative terminal or removing the fuses (EFI and ETC-S fuses), performing the following procedures in order to quickly relearn the Deposit Loss Flow value. After the Deposit Loss Flow has been relearned, gradual fine adjustments will continue automatically.

-

Start the engine cold and allow the engine to idle.

-

After the engine is warmed up (engine coolant temperature is above 80°C [176°F]), allow the engine to idle for an additional 5 minutes.

-

Turn the engine switch off and wait for 30 seconds.

-

Start the engine again, and allow the engine to idle for 5 minutes.



Injector (Port) Injection duration of No. 1 cylinder:
Min.: 0 μs., Max.: 65535 μs.
- -
Injection Volum (Cylinder 1) Injection volume (Cylinder 1):
Min.: 0 ml, Max.: 2.047 ml
0.7 to 1.5 ml: Idling Total fuel injection volume of 10 injections
Fuel Pump/Speed Status Fuel pump status:
ON or OFF
ON: Engine running -
Current Fuel Type Current fuel type Gasoline/petrol -
EVAP (Purge) VSV Purge VSV control duty:
Min.: 0%, Max.: 100%
0 to 50%: Idling Order signal from ECM
EVAP Purge Flow Ratio of evaporative purge flow to intake air volume:
Min.: 0%, Max.: 399.99%
0 to 4%: Idling -
Purge Density Learn Value Learning value of purge density:
Min.: -50%/%, Max.: 199.99%/%
- -
EVAP Purge VSV Purge VSV status:
ON or OFF
- -
Purge Cut VSV Duty Purge VSV duty:
Min.: 0%, Max.: 399.9%
- -
Target Air-Fuel Ratio Ratio compared to stoichiometric level:
Min.: 0, Max.: 1.99
0.8 to 1.2: Idling
·

0 to 0.999 = Rich

·

1 = Stoichiometric air fuel ratio

·

1.001 to 1.999 = Lean


AF Lambda B1S1 Short-term fuel trim associated with bank 1 sensor 1:
Min.: -0, Max.: 1.99
·

Value less than 1 (0.000 to 0.999) = Rich

·

Stoichiometric air-fuel ratio = 1

·

Value greater than 1 (1.001 to 1.999) = Lean


-
AFS Voltage B1S1 Air fuel ratio sensor output voltage for bank 1 sensor 1:
Min.: 0 V, Max.: 7.99 V
3 to 3.5 V: Idling Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output voltage of sensor
AFS Current B1S1 A/F sensor output current for bank 1 sensor 1: Min.: -128 mA, Max.: 127.99 mA - -
A/F Heater Duty #1 Air fuel ratio heater duty ratio for bank 1:
Min.: 0%, Max.: 399.9%
0 to 100% -
O2S B1S2 Heated oxygen sensor output voltage for bank 1 sensor 2:
Min.: 0 V, Max.: 1.275 V
0.1 to 0.9 V:
Driving at 70 km/h (44 mph)
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output voltage of sensor
O2 Heater B1S2 Heated oxygen sensor heater for bank 1 sensor 2:
Not Act or Active
- -
O2 Heater Curr Val B1S2 Heated oxygen sensor heater for bank 1 sensor 2:
Min.: 0 A, Max.: 4.9 A
- -
Short FT #1 Short-term fuel trim:
Min.: -100%, Max.: 99.2%
-15 to 15% Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio
Long FT #1 Long-term fuel trim:
Min.: -100%, Max.: 99.2%
-15 to 15% Overall fuel compensation carried out in long-term to compensate for a continual deviation of short-term fuel trim from central value
Total FT #1 Total fuel trim value for fuel system:
Min.: -0.5, Max.: 0.496
-0.2 to 0.2 -
Fuel System Status #1 Fuel system status:
OL or CL or OLDrive or OLFault or CLFault or Unused
CL: Idling after warming up
·

OL (Open Loop): Has not yet satisfied conditions to go closed loop

·

CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control

·

OLDrive: Open loop due to driving conditions (fuel enrichment)

·

OLFault: Open loop due to detected system fault

·

CLFault: Closed loop but air fuel ratio sensor, which is used for fuel control, malfunctioning


Fuel System Status #2 - Unused -
IGN Advance Ignition timing advance for No. 1 cylinder:
Min.: -64 deg., Max.: 63.5 deg.
5 to 22 deg.: Idling
(Neutral position)
-
Knock Feedback Value Knock feedback value:
Min.: -64°CA, Max.: 1023.9°CA
-20 to 0°CA:
Driving at 70 km/h (44 mph)
-
Knock Correct Learn Value Knock correction learning value:
Min.: -64°CA, Max.: 1023.9°CA
0 to 20°CA:
Driving at 70 km/h (44 mph)
-
Idle Spark Advn Ctrl #1 Individual cylinder timing advance compensation amount (No. 1):
Min.: 0°CA, Max.: 15.93°CA
- When the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #2 Individual cylinder timing advance compensation amount (No. 2):
Min.: 0°CA, Max.: 15.93°CA
- When the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #3 Individual cylinder timing advance compensation amount (No. 3):
Min.: 0°CA, Max.: 15.93°CA
- When the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #4 Individual cylinder timing advance compensation amount (No. 4):
Min.: 0°CA, Max.: 15.93°CA
- When the engine stalls, is difficult to start, or idles roughly
VVT Control Status #1 VVT control (bank 1) status:
ON or OFF
- -
VVT Advance Fail VVT control failure status:
ON or OFF
ON: VVT control failure -
VVT Aim Angle #1*1 VVT aim angle (bank 1):
Min.: 0%, Max.: 399.9%
- VVT duty signal value during operation
VVT Change Angle #1*1 VVT change angle (bank 1):
Min.: 0 °FR, Max.: 639.9 °FR
- Displacement angle during operation
VVT OCV Duty #1*1 VVT camshaft timing oil control valve operation duty:
Min.: 0%, Max.: 399.9%
- Requested duty value for operation
VN Turbo Type Variable nozzle turbo type:
Not Avl or Commo or Vacuum or CAN Com
Not Avl (Unused) -
Catalyst Temp B1S1 Estimated catalyst temperature (bank 1, sensor 1):
Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F)
- -
Catalyst Temp B1S2 Estimated catalyst temperature (bank 1, sensor 2):
Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F)
- -
Starter Signal Engine switch (STSW) signal:
Open or Close
Open: Starter signal on
Close: Starter signal off
-
Starter Control Starter signal status:
ON or OFF
ON: Cranking -
Power Steering Signal Power steering signal:
ON or OFF
ON: Power steering operation -
Starter Relay Starter relay ON or OFF ON: Cranking -
ACC Relay ACC cut relay ON or OFF ON: Cranking -
Neutral Position SW Signal Park/neutral position switch status:
ON or OFF
ON: Neutral position -
Stop Light Switch Stop light switch:
ON or OFF
ON: Brake pedal depressed -
A/C Signal Air conditioning signal:
ON or OFF
ON: Air conditioning ON -
Idle Up Signal Idle up signal:
ON or OFF
- -
Closed Throttle Position SW Closed throttle position switch:
ON or OFF
ON: Throttle fully closed
OFF: Throttle open
-
Fuel Cut Condition Fuel cut determination flag:
ON or OFF
- -
Check Mode Check mode:
ON or OFF
ON: Check mode ON See page (Click here)
SPD Test Result Check mode result for vehicle speed sensor:
Compl or Incmpl
- -
Misfire Test Result Check mode result for misfire monitor:
Compl or Incmpl
- -
OXS1 Test Result Check mode result for heated oxygen sensor:
Compl or Incmpl
- -
A/F Test Results #1 Check mode result for air fuel ratio sensor:
Compl or Incmpl
- -
Complete Parts Monitor Comprehensive component monitor:
Avail or Not Avl
- -
Fuel System Monitor Fuel system monitor:
Avail or Not Avl
- -
Misfire Monitor Misfire monitor:
Avail or Not Avl
- -
EGR/VVT Monitor EGR/VVT monitor:
Avail or Not Avl
- -
EGR/VVT Monitor EGR/VVT monitor:
Compl or Incmpl
- -
O2S (A/FS) Heater Monitor O2S (A/FS) heater monitor/
Not Avl or Avail
- -
O2S (A/FS) Heater Monitor O2S (A/FS) heater monitor/
Compl or Incmpl
- -
O2S (A/FS) Monitor O2S (A/FS) monitor:
Avail or Not Avl
- -
O2S (A/FS) Monitor O2S (A/FS) monitor:
Compl or Incmpl
- -
A/C Monitor A/C monitor/
Not Avl or Avail
- -
A/C Monitor A/C monitor/
Compl or Incmpl
- -
2nd Air Monitor 2nd air monitor/
Not Avl or Avail
- -
2nd Air Monitor 2nd air monitor/
Compl or Incmpl
- -
EVAP Monitor EVAP monitor
Not Avl or Avail
- -
EVAP Monitor EVAP monitor
Compl or Incmpl
- -
Heated Catalyst Monitor Heated catalyst monitor/
Not Avl or Avail
- -
Heated Catalyst Monitor Heated catalyst monitor/
Compl or Incmpl
- -
Catalyst Monitor Catalyst monitor:
Avail or Not Avl
- -
Catalyst Monitor Catalyst monitor:
Compl or Incmpl
- -
TC Terminal TC terminal status:
ON or OFF
- -
# Codes (Include History) Number of codes:
Min.: 0, Max.: 255
- Number of detected DTCs
MIL MIL status:
ON or OFF
ON: MIL ON -
MIL ON Run Distance Distance traveled since MIL turned ON:
Min.: 0 Km, Max.: 65535 Km
Distance since DTC detected -
Running Time from MIL ON Running time since MIL turned ON:
Min.: 0 min, Max.: 65535 min
Equivalent to running time since MIL turned ON -
Time after DTC Cleared Time since DTCs cleared:
Min.: 0 min, Max.: 65535 min
Equivalent to time since DTCs cleared -
Distance from DTC Cleared Distance traveled since DTCs cleared:
Min.: 0 km, Max.: 65535 km
Equivalent to distance driven since DTCs cleared -
Warmup Cycle Cleared DTC Warm-up cycles since DTCs cleared:
Min.: 0, Max.: 255
- Number of warm-up cycles since DTCs cleared
Dist Batt Cable Disconnect Distance after battery cable disconnected:
Min.: 0 km, Max.: 65535 km
Total distance vehicle driven after battery cable disconnected -
OBD Requirements OBD requirements EOBD (Euro-OBD) -
Number of Emission DTC Number of emission DTCs - -
TC and TE1 TC and CG (TE1) terminals of DLC3:
ON or OFF
- -
Ignition Trig. Count Ignition counter:
Min.: 0, Max.: 65535
0 to 400 -
Cylinder #1 Misfire Count Misfire count of cylinder 1:
Min.: 0, Max.: 255
0: Normal -
Cylinder #2 Misfire Count Misfire count of cylinder 2:
Min.: 0, Max.: 255
0: Normal -
Cylinder #3 Misfire Count Misfire count of cylinder 3:
Min.: 0, Max.: 255
0: Normal -
Cylinder #4 Misfire Count Misfire count of cylinder 4:
Min.: 0, Max.: 255
0: Normal -
All Cylinders Misfire Count Misfire count of all cylinders:
Min.: 0, Max.: 255
0: Normal -
Misfire RPM Engine speed when misfire occurs:
Min.: 0 rpm, Max.: 6375 rpm
0 rpm: Normal -
Misfire Load Engine load when misfire occurred:
Min.: 0 g/rev, Max.: 3.98 g/rev
- -
Misfire Margin Margin to detect engine misfire
Min.: -100%, Max.: 127%
0 to 127%: Idling Misfire detection margin
Engine Speed (Starter Off) Engine speed when starter off:
Min.: 0 rpm, Max.: 51199 rpm
- When the engine stalls, is difficult to start, or idles roughly
Starter Count Number of times starter turned on after engine switch turned from off to on (IG):
Min.: 0, Max.: 255
- When the engine stalls, is difficult to start, or idles roughly
Engine Starting Time Engine run time (elapsed time from engine switch on (IG) to off):
Min.: 0 ms, Max.: 655350 ms
- When the engine stalls, is difficult to start, or idles roughly
Run Dist of Previous Trip Distance traveled during previous trip:
Min.: 0 km, Max.: 655.35 km
-
·

Run Dist of Previous Trip continues to display the distance traveled in the previous trip during the detection period of DTC P1604, which ends 5 seconds after the engine starts.

Then the previous trip distance will be cleared and the distance traveled during this trip, which is calculated based on the vehicle speed, will be displayed.

·

When the engine is difficult to start and DTC P1604 is stored, Run Dist of Previous Trip will continue to be displayed.

When inspecting for DTCs other than P1604, or when taking a snapshot, the distance traveled during this trip will be displayed.


Engine Starting Time Engine run time (elapsed time from engine switch on (IG) to off):
Min.: 0 ms, Max.: 655350 ms
- When the engine stalls, is difficult to start, or idles roughly
Previous Trip Coolant Temp Coolant temperature of previous trip:
Min.: -40°C (-40°F), Max.: 215°C (419°F)
- When the engine stalls, is difficult to start, or idles roughly
Previous Trip Intake Temp Intake air Coolant temperature of previous trip:
Min.: -40°C (-40°F), Max.: 215°C (419°F)
- When the engine stalls, is difficult to start, or idles roughly
Engine Oil Temperature Engine oil temperature (estimated):
Min.: -40°C (-40°F), Max.: 215°C (419°F)
- When the engine stalls, is difficult to start, or idles roughly
Previous Trip Eng Oil Temp Engine oil temperature of previous trip (estimated):
Min.: -40°C (-40°F), Max.: 215°C (419°F)
- When the engine stalls, is difficult to start, or idles roughly
Ambient Temp for A/C Ambient temperature:
Min.: -40°C (-40°F), Max.: 215°C (419°F)
- When the engine stalls, is difficult to start, or idles roughly
Previous Trip Ambient Temp Ambient temperature of previous trip:
Min.: -40°C (-40°F), Max.: 215°C (419°F)
- When the engine stalls, is difficult to start, or idles roughly
Engine Start Hesitation History of instances of slow engine starts:
ON or OFF
- -
Low Rev for Eng Start History of low engine speed after engine starts:
ON or OFF
- -
Minimum Engine Speed Minimum engine speed:
Min.: 0 rpm, Max.: 51199 rpm
- When the engine stalls, is difficult to start, or idles roughly
Battery Current Battery Current/
Min.: -125 A, Max.: 124.9 A
- -
Battery Temperature Battery temperature/
Min.: -45°C (-49°F), Max.: 6513.5°C (11756.3°F)
- -
Alternator Output Duty Generator output duty/
Min.: 0%, Max.: 399.9%
- Electricity generated by alternator is output through duty ratio charging control service data
Alt Vol - Non Active Test Request voltage when regulator not under forced activation/
Min.: 0 V, Max.: 20 V
Battery electrolyte temperature varies (12.5 to 14.8 V) while driving: After engine start Alternator regulator output voltage is output when performing Active Test, value is 0 V
Alt Vol - Active Test Request voltage when regulator under forced activation/
Min.: 0 V, Max.: 20 V
Request instruction voltage value: After engine start Charging control service data When not performing Active Test, value is 0 V
Electric Fan Motor Electric fan motor:
ON or OFF
- -
Brake Override System Brake override system status:
ON or OFF
ON: Brake override system operating -
Idle Fuel Cut Fuel cut idle:
ON or OFF
ON: Fuel cut operating -
FC TAU Fuel cut TAU (Fuel cut with very light load):
ON or OFF
ON: Fuel cut operating Fuel cut being performed during very light load to prevent incomplete engine combustion
Immobiliser Fuel Cut Status of the immobiliser fuel cut:
ON or OFF
- -
Electrical Load Signal 1 Status of electrical load signal:
ON or OFF
ON: Electrical signal on -
Electrical Load Signal 2 Electrical load signal:
ON or OFF
- -
Electrical Load Signal 3 Electrical load signal:
ON or OFF
- -
Model Code Identifies model code ACR5# -
Engine Type Identifies engine type 2AZFE -
Cylinder Number Identifies number of cylinders
Min.: 0, Max.: 255
4 -
Transmission Type Identifies transmission type CVT -
Destination Identifies destination W -
Model Year Identifying model year:
Min.: 1900, Max.: 2155
20## -
System Identification System identification Gasoline (gasoline engine) -
Engine Speed of Cyl #2 Engine speed during No. 2 cylinder fuel cut:
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
Engine Speed of Cyl #3 Engine speed during No. 3 cylinder fuel cut:
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
Engine Speed of Cyl #4 Engine speed during No. 4 cylinder fuel cut:
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
Av Engine Speed of All Cyl Average of Engine speed values during fuel cut of No. 1 to No. 4 cylinder:
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed

HINT:

*1: Data List values are displayed only when performing the following Active Test: Control the VVT Linear (Bank 1). For other Active Tests, the Data List value will be 0.

*2: Excluding throttle valve opening percentage due to Idle Speed Control (ISC).


for A/T Models
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed:
Min.: 0 km/h, Max.: 255 km/h
Actual vehicle speed Speed indicated on speedometer
Engine Speed Engine speed:
Min.: 0 rpm, Max.: 16383 rpm:
600 to 700 rpm: Idling -
Calculate Load Calculated load by ECM:
Min.: 0%, Max.: 100%
·

3.3 to 26.7 %: Idling with warm engine

·

12 to 14.7 %: Running without load (2000 rpm)


-
MAF Air flow rate from mass air flow meter:
Min.: 0 gm/sec, Max.: 655.35 gm/sec
0.58 to 4.67 gm/sec: Idling with warm engine
3.33 to 9.17 gm/sec: 2500 rpm with warm engine
If value approximately 0.0 gm/sec:
·

Mass air flow meter power source circuit open

·

VG circuit open or shorted


If 271.0 gm/sec. or more:
·

E2G circuit open


Atmosphere Pressure Atmospheric pressure:
Min.: 0 kPa, Max.: 255 kPa
Equivalent to atmospheric pressure (absolute pressure) -
Coolant Temp Engine coolant temperature:
Min.: -40°C (-40°F), Max.: 140°C (284°F)
80 to 105°C (176 to 221°F):
After warming up
·

If value -40°C (-40°F): sensor circuit open

·

If value 140°C (284°F) or more: sensor circuit shorted


Intake Air Intake air temperature:
Min.: -40°C (-40°F), Max.: 140°C (284°F)
Equivalent to ambient air temperature
·

If value -40°C (-40°F): sensor circuit open

·

If value 140°C (284°F) or more: sensor circuit shorted


Engine Run Time Engine run time:
Min.: 0 s, Max.: 65535 s
Time since engine start -
Initial Engine Coolant Temp Engine coolant temperature at engine start:
Min.: -40°C (-40°F), Max.: 120°C (248°F)
- -
Initial Intake Air Temp Intake air temperature at engine start:
Min.: -40°C (-40°F), Max.: 120°C (248°F)
- -
Battery Voltage Battery voltage:
Min.: 0 V, Max.: 65.5 V
11 to 14 V: Engine switch on (IG) -
Accel Sens. No. 1 Volt % Absolute accelerator pedal position No. 1:
Min.: 0%, Max.: 100%
10 to 22%: Accelerator pedal fully released
50 to 90%: Accelerator pedal fully depressed
-
Accel Sens. No. 2 Volt % Absolute accelerator pedal position No. 2:
Min.: 0%, Max.: 100%
24 to 40%: Accelerator pedal fully released
68 to 95%: Accelerator pedal fully depressed
-
Accel Sensor Out No. 1 Accelerator pedal position sensor No. 1 voltage:
Min.: 0 V, Max.: 4.9 V
0.5 to 1.1 V: Accelerator pedal fully released
2.6 to 4.5 V: Accelerator pedal fully depressed
-
Accel Sensor Out No. 2 Accelerator pedal position sensor No. 2 voltage:
Min.: 0 V, Max.: 4.9 V
1.2 to 2.0 V: Accelerator pedal fully released
3.4 to 4.7 V: Accelerator pedal fully depressed
-
Accelerator Idle Position Whether or not accelerator pedal position sensor detecting idle:
ON or OFF
ON: Idling -
Accel Fully Close #1 (AD) Accelerator fully closed value No. 1 voltage (AD):
Min.: 0 V, Max.: 4.9 V
- -
Accel Fully Close Learn #1 Accelerator fully closed learning value No. 1:
Min.: 0 deg, Max.: 124.5 deg
- -
Accel Fully Close Learn #2 Accelerator fully closed learning value No. 2:
Min.: 0 deg, Max.: 124.5 deg
- -
Throttle Sensor Volt % Throttle valve opening percentage according to throttle position sensor:
Min.: 0%, Max.: 100%
·

10 to 22%: Accelerator pedal fully released

·

64 to 96%: Accelerator pedal fully depressed


Value calculated based on the voltage at terminal VTA1
Throttl Sensor #2 Volt % Throttle valve opening percentage according to throttle position sensor No. 2:
Min.: 0%, Max.: 100%
·

42 to 62%: Accelerator pedal fully released

·

92 to 100%: Accelerator pedal fully depressed


Value calculated based on the voltage at terminal VTA2
ST1 Brake pedal signal:
ON or OFF
OFF: Brake pedal depressed -
System Guard System guard:
ON or OFF
- -
Open Side Malfunction Open side malfunction:
ON or OFF
- -
Throttle Idle Position Whether or not throttle position sensor detecting idle:
ON or OFF
·

ON: Accelerator pedal fully released

·

OFF: Accelerator pedal fully depressed


-
Throttle Require Position Required throttle position:
Min.: 0 V, Max.: 4.9 V
0.5 to 1.1 V: Idling -
Throttle Sensor Position*2 Throttle position sensor:
Min.: 0%, Max.: 100%
·

0%: Accelerator pedal fully released

·

50 to 80%: Accelerator pedal fully depressed


Recognition value for throttle opening angle on ECM
Throttle Position No. 1 Throttle position sensor No. 1 output voltage:
Min.: 0 V, Max.: 4.9 V
·

0.5 to 1.1 V: Accelerator pedal fully released

·

3.2 to 4.8 V: Accelerator pedal fully depressed

·

0.6 to 1.4 V: Fail-safe operating


-
Throttle Position No. 2 Throttle position sensor No. 2 output voltage:
Min.: 0 V, Max.: 4.9 V
·

2.1 to 3.1 V: Accelerator pedal fully released

·

4.6 to 4.9 V: Accelerator pedal fully depressed

·

2.1 to 3.1 V: Fail-safe operating


-
Throttle Position Command Throttle position command value:
Min.: 0 V, Max.: 4.9 V
- -
Throttle Sens Open Pos #1 Throttle sensor opener position No. 1:
Min.: 0 V, Max.: 4.9 V
0.6 to 1.4 V -
Throttle Sens Open Pos #2 Throttle sensor opener position No. 2:
Min.: 0 V, Max.: 4.9 V
1.7 to 2.5 V -
Throttle Sens Open #1 (AD) Throttle position sensor No. 1 output voltage (AD):
Min.: 0 V, Max.: 4.9 V
0.5 to 4.9 V -
Throttle Motor Whether or not throttle actuator control permitted:
ON or OFF
ON: Engine switch on (IG)
OFF: Electronic throttle control system has failed
-
Throttle Motor Current Throttle actuator current:
Min.: 0 A, Max.: 19.9 A
0 to 3.0 A: Idling -
Throttle Motor DUTY Throttle actuator:
Min.: 0%, Max.: 100%
10 to 20%: Idling after engine warmed up -
Throttle Motor Duty (Open) Throttle actuator duty ratio (open):
Min.: 0%, Max.: 100%
0 to 40%: Idling -
Throttle Motor Duty (Close) Throttle actuator duty ratio (close):
Min.: 0%, Max.: 100%
0 to 40%: Idling -
Throttle Fully Close Learn Throttle valve fully closed
(learned value):
Min.: 0 V, Max.: 4.9 V
0.4 to 1.0 V: Accelerator pedal fully released -
ETCS Actuator Power Electronic throttle control system power supply:
ON or OFF
ON: Engine switch on (IG) and system normal
OFF: Electronic throttle control system has failed
-
+BM Voltage +BM voltage:
Min.: 0 V, Max.: 19.9 V
11 to 14 V: Engine switch on (IG) and system normal -
Actuator Power Supply Throttle actuator power supply:
ON or OFF
·

ON: Engine switch on (IG) and system normal

·

OFF: Electronic throttle control system has failed


-
Clutch Current Clutch current:
Min.: 0 A, Max.: 2.49 A
- -
Fail Safe Drive Whether or not fail safe function executed:
ON or OFF
ON: Electronic throttle control system has failed
OFF: Electronic throttle control system normal
-
Fail Safe Drive (Main CPU) Whether or not fail safe function executed:
ON or OFF
ON: Electronic throttle control system has failed
OFF: Electronic throttle control system normal
-
Injector (Port) Injection duration of No. 1 cylinder:
Min.: 0 ms, Max.: 32.64 ms
1.5 to 2.7 ms: Idling with warm engine -
Injection Volum (Cylinder 1) Injection volume (cylinder 1):
Min.: 0 ml, Max.: 2.047 ml
0.05 to 0.15 ml: idling with warm engine Total fuel injection volume of 10 injections
Fuel Pump/Speed Status Fuel pump/status:
ON or OFF
ON: Cranking -
EVAP (Purge) VSV Purge VSV control duty:
Min.: 0%, Max.: 100%
10 to 50%: Idling with warm engine Order signal from ECM
EVAP Purge Flow Purge flow:
Min.: 0%, Max.: 102.3%
0 to 10%: Idling with warm engine -
Purge Density Learn Value Learning value of purge density:
Min.: -50, Max.: 349.99
-40 to 10: Idling with warm engine -
EVAP Purge VSV Purge VSV status:
ON or OFF
OFF: Engine moving at 3000 rpm or more after warming up
ON: Accelerator pedal released
-
Target Air-Fuel Ratio Ratio compared to stoichiometric level:
Min.: 0, Max.: 1.998
0.8 to 1.2: Idling with warm engine
·

Value less than 1 (0.000 to 0.999) = Rich

·

Stoichiometric air fuel ratio=1

·

Value greater than 1 (1.001 to 1.999) = Lean


AF Lambda B1S1 Short-term fuel trim associated with bank 1 sensor 1:
Min.: 0, Max.: 1.99
·

Value less than 1 (0.000 to 0.999) = Rich

·

Stoichiometric air fuel ratio=1

·

Value greater than 1 (1.001 to 1.999) = Lean


-
AFS Voltage B1S1 Air fuel ratio sensor output voltage for bank 1 sensor 1:
Min.: 0 V, Max.: 7.99 V
2.8 to 3.8 V: Idling Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of air fuel ratio sensor
AFS Current B1S1 Air fuel ratio sensor current for bank 1 sensor 1:
Min.: -128 mA, Max.: 127.99 mA
- -
O2S B1S2 Heated oxygen sensor output voltage for bank 1 sensor 2:
Min.: 0 V, Max.: 1.27 V
0.1 to 1.0 V: 2500 rpm Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of heated oxygen sensor
Short FT #1 Short-term fuel trim of bank 1:
Min.: -100%, Max.: 99.2%
-15 to 15% Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio
Long FT #1 Long-term fuel trim of bank 1:
Min.: -100%, Max.: 99.2%
-15 to 15% Overall fuel compensation carried out long-term to compensate continual deviation of short-term fuel trim from central value
Total FT #1 Total fuel trim value for fuel system:
Min.: -0.5, Max.: 0.496
-0.28 to 0.2: Idling -
Fuel System Status #1 Fuel system status (bank 1):
OL or CL or OLDrive or OLFault or CLFault or Unused
CL: Idling after warming up
·

OL (Open Loop): Has not yet satisfied conditions to go closed loop

·

CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control

·

OLDrive: Open loop due to driving conditions (fuel enrichment)

·

OLFault: Open loop due to detected system fault

·

CLFault: Closed loop but air fuel ratio sensor, which used for fuel control malfunctioning


Fuel System Status #2 - Unused -
IGN Advance Ignition timing advance for No. 1 cylinder:
Min.: -64 deg, Max.: 63.5 deg
5 to 15 deg.: Idling -
Knock Feedback Value Feedback value of knocking:
Min.: -64 °CA, Max.: 1984 C°A
-20 to 0 °CA: Driving at 70 km/h (44 mph) -
Knock Correct Learn Value Correction learning value of knocking:
Min.: -64 °CA, Max.: 1984 °CA
0 to 20 °CA: Driving at 70 km/h (44 mph) -
VVT Control Status #1 VVT control (bank 1) status:
ON or OFF
- -
VVT Aim Angle #1*1 VVT aim angle (bank 1):
Min.: 0%, Max.: 100%
- VVT duty signal value during intrusive operation
VVT Change Angle #1*1 VVT change angle (bank 1):
Min.: 0 DegFR, Max.: 60 DegFR
- Displacement angle during intrusive operation
VVT OCV Duty #1*1 VVT camshaft timing oil control valve operation duty:
Min.: 0%, Max.: 100%
- Requested duty value for intrusive operation
Catalyst Temp B1S1 Estimated catalyst temperature (bank 1, sensor 1):
Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F)
- -
Catalyst Temp B1S2 Estimated catalyst temperature (bank 1, sensor 2):
Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F)
- -
Starter Signal Starter signal:
ON or OFF
ON: Starter signal on
OFF: Starter signal off
-
Starter Control Starter switch signal:
ON or OFF
ON: Cranking -
Power Steering Signal Power steering signal:
ON or OFF
ON: Power steering operation -
Starter Relay ST relay:
ON or OFF
ON: Cranking -
Power Steer Sig. Record Power steering signal:
ON or OFF
ON: When steering wheel first turned after engine switch turned on (IG) -
ACC Relay ACC relay cut signal:
ON or OFF
ON: Cranking -
Neutral Position SW Signal Park/neutral position switch status:
ON or OFF
ON: P or N position -
Stop Light Switch Stop light switch:
ON or OFF
ON: Brake pedal depressed -
A/C Signal A/C signal:
ON or OFF
ON: Air conditioning on -
Electrical Load Signal Electrical load signal:
ON or OFF
ON: Headlights or defogger turned on -
Check Mode Check mode:
ON or OFF
ON: Check mode on See page (Click here)
SPD Test Result Check mode result for vehicle speed sensor:
Compl or Incmpl
- -
OXS1 Test Result Check mode result for heated oxygen sensor (bank 1):
Compl or Incmpl
- -
A/F Test Results #1 Check mode result for air fuel ratio sensor (bank 1):
Compl or Incmpl
- -
# Codes (Include History) #Codes:
Min.: 0, Max.: 255
- Number of detected DTCs
MIL MIL status:
ON or OFF
ON: MIL on -
Time after DTC Cleared Time after DTC cleared:
Min.: 0 min, Max.: 65535 min
Equivalent to time after DTCs cleared -
Distance from DTC Cleared Distance after DTC cleared:
Min.: 0 km, Max.: 65535 km
Equivalent to drive distance after DTCs cleared -
Warmup Cycle Cleared DTC Warm-up cycle after DTC cleared:
Min.: 0, Max.: 255
- Number of warm-up cycles after DTC cleared
Number of Emission DTC Emission related DTCs:
Min.: 0, Max.: 127
- Number of emission related DTCs
TC and TE1 TC and TE1 terminals of DLC3:
ON or OFF
- -
Cylinder #1 Misfire Count Misfire count of cylinder 1:
Min.: 0, Max.: 255
0: Normal -
Cylinder #2 Misfire Count Misfire count of cylinder 2:
Min.: 0, Max.: 255
0: Normal -
Cylinder #3 Misfire Count Misfire count of cylinder 3:
Min.: 0, Max.: 255
0: Normal -
Cylinder #4 Misfire Count Misfire count of cylinder 4:
Min.: 0, Max.: 255
0: Normal -
All Cylinders Misfire Count Misfire count of all cylinders:
Min.: 0, Max.: 255
0: Normal -
Misfire RPM Engine speed when misfire occurs:
Min.: 0 rpm, Max.: 6375 rpm
0 rpm: Normal -
Misfire Load Engine load when misfire occurred:
Min.: 0 g/rev, Max.: 3.98 g/rev
- -
Misfire Margin Margin to detect engine misfire
Min.: -100%, Max.: 99.21%
0 to 99.21%: Idling Misfire detection margin
Electric Fan Motor Electric fan motor:
ON or OFF
- -
Idle Fuel Cut Fuel cut idle:
ON or OFF
ON: Fuel cut operating -
FC TAU Fuel cut TAU (Fuel cut during very light load):
ON or OFF
ON: Fuel cut operating Fuel cut being performed under very light load to prevent incomplete engine combustion
Model Code Identifies model code ACR5# -
Engine Type Identifies engine type 2AZFE -
Cylinder Number Identifies number of cylinders 4 -
Transmission Type Identifies transmission type ECT 4th -
Destination Identifies destination W -
Model Year Identifies model year 20## -

HINT:

*1: Data List values are displayed only when performing the following Active Test: Control the VVT Linear (Bank 1). For other Active Tests, the Data List value will be 0.

*2: Excluding throttle valve opening percentage due to Idle Speed Control (ISC).


ACTIVE TEST


HINT:

Performing an Active Test enables components including the relays, VSV (Vacuum Switching Valve) and actuators, to be operated without removing any parts. The Active Test can be performed with the intelligent tester. Performing the Active Test as the first step of troubleshooting is one method of shortening diagnostic time.


Data List can be displayed during Active Test.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


d.

Perform the Active Tests by referring to the table below.



Tester Display Test Part Control Range Diagnostic Note
Control the Injection Volume Change injection volume Between -12.5 and 24.8%
·

All injectors tested at the same time

·

Perform test at less than 3000 rpm

·

Injection volume can be changed in fine graduations within control range


Control the Injection Volume for A/F Sensor Change injection volume -12.5%/0%/12.5%
·

Perform test at less than 3000 rpm

·

Control the Injection Volume for A/F Sensor enables to check and graph air fuel ratio sensor and heated oxygen sensor voltage outputs

·

When conducting the test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / Data List / AFS Voltage B1S1 and O2S B1S2


Activate the VSV for Evap Control Activate purge VSV control ON/OFF -
Control the Fuel Pump / Speed Activate fuel pump (C/OPN Relay) ON/OFF Test is possible with engine stopped
Connect the TC and TE1 Turn on and off TC and TE1 connection ON/OFF
·

ON: TC and TE1 connected

·

OFF: TC and TE1 disconnected


Control the Idle Fuel Cut Prohibit Prohibit idle fuel cut control ON/OFF -
Control the Electric Cooling Fan Control electric cooling fan ON/OFF -
Activate the Starter Relay Activate starter relay ON/OFF -
Activate the ACC Cut Relay Activate ACC cut relay ON/OFF Test is possible when following conditions are met:
·

Engine switch on (IG)

·

Engine is stopped


Control the ETCS Open/Close Slow Speed Throttle actuator Close/Open: Throttle valve opens/closes slowly Test is possible when following conditions are met:
·

Engine is stopped

·

Shift lever in P

·

Accelerator pedal fully depressed (accelerator pedal position: 58° or more)


Control the ETCS Open/Close Fast Speed Throttle actuator Close/Open: Throttle valve opens/closes fast
Control the VVT Linear (Bank 1) Control oil control valve (bank 1) -128 to 127%
This value added to present oil control valve control duty
100%: Maximum advance
-100%: Maximum retard
·

Engine stalls or idles roughly when oil control valve is operated at 100%.

·

Test is possible with vehicle stopped and engine idling.

·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.


Control the VVT System (Bank 1) Control oil control valve (bank 1) OFF/ON
·

Test is possible with vehicle stopped and engine idling.

·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.


Control the Voltage of Alternator Request output voltage of generator regulator during forced activation Between 12.5 to 14.8 Test is possible with vehicle stopped and engine idling.
Control the Cylinder #1 Fuel Cut Cylinder #1 injector fuel cut ON/OFF Test is possible with vehicle stopped and engine idling.
Control the Cylinder #2 Fuel Cut Cylinder #2 injector fuel cut ON/OFF
Control the Cylinder #3 Fuel Cut Cylinder #3 injector fuel cut ON/OFF
Control the Cylinder #4 Fuel Cut Cylinder #4 injector fuel cut ON/OFF
Control the All Cylinders Fuel Cut Control the all cylinder fuel cut ON/OFF Test is possible while vehicle stopped and engine idling.
Check the Cylinder Compression*1 Check the cylinder compression pressure ON/OFF Fuel injection and ignition are stopped in all cylinders

HINT:

*1: In this Active Test, the fuel and ignition of all cylinders is cut. The engine must then be cranked for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.


1.

Warm up the engine.

2.

Turn the engine switch off.

3.

Connect the intelligent tester to the DLC3.

4.

Turn the engine switch on (IG).

5.

Turn the tester on.

6.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

HINT:

To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.


7.

Push the snapshot button to turn the snapshot function on.

HINT:

Using the snapshot function, data can be recorded during the Active Test.


8.

While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

HINT:

After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.


9.

Crank the engine for about 10 seconds.

HINT:

Continue to crank the engine until the values change from the default value (51199 rpm).


10.

Monitor the engine speed (Engine Speed of Cyl #1 to #4) displayed on the tester.

HINT:

At first, the tester displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.


NOTICE:
·

Do not crank the engine continuously for 20 seconds or more.

·

If it is necessary to crank the engine again after Check the Cylinder Compression has been changed to ON and the engine has been cranked once, press Exit to return to the Active Test menu screen. Then change Check the Cylinder Compression to ON and crank the engine.

·

Use a fully-charged battery.



11.

Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.

NOTICE:

If the Active Test is changed to OFF while the engine is being cranked, the engine will start.


12.

Push the snapshot button to turn the snapshot function off.

13.

Enter the following menus: Function / Snapshot Review / Engine and ECT / Snapshot File Manager, select the recorded data and display the data.

HINT:

If the data is not displayed as a graph, the change of the values cannot be observed.


14.

Check the change in engine speed values.

HINT:

As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.