| Vehicle Speed
|
Vehicle speed:
Min.: 0 km/h, Max.: 255 km/h
|
Actual vehicle speed
|
Speed indicated on speedometer
|
| Engine Speed
|
Engine speed:
Min.: 0 rpm, Max.: 16383 rpm
|
670 to 770 rpm: Idling
|
-
|
| Calculate Load
|
Calculated load by ECM:
Min.: 0%, Max.: 100%
|
·
24 to 30%: Running without load at 2000 rpm
|
-
|
| Vehicle Load
|
Vehicle load:
Min.: 0%, Max.: 25700%
|
Actual vehicle load
|
Load percentage in terms of maximum intake air flow amount
|
| MAF
|
Air flow rate from mass air flow meter:
Min.: 0 gm/sec, Max.: 655.35 gm/sec
|
·
2.1 to 3.1 gm/sec.: Idling
·
6.2 to 8.7 gm/sec.: 2000 rpm
·
9.8 to 13.5 gm/sec.: 3000 rpm
|
If value is approximately 0.0 gm/sec:
·
Mass air flow meter power source circuit open
·
VG circuit open or shorted
If value is 271.0 gm/sec or more:
|
| Atmosphere Pressure
|
Atmospheric pressure:
Min.: 0 kPa, Max.: 255 kPa
|
Approximately 100 kPa: Engine switch on (IG)
|
-
|
| Coolant Temp
|
Engine coolant temperature:
Min.: -40°C (-40°F), Max.: 140°C (284°F)
|
80 to 95°C
(176 to 203°F): After warming up
|
·
If -40°C (-40°F): sensor circuit open
·
If 140°C (284°F) or more: sensor circuit shorted
|
| Intake Air
|
Intake air temperature:
Min.: -40°C (-40°F), Max.: 140°C (284°F)
|
Equivalent to ambient air temperature
|
·
If -40°C (-40°F): sensor circuit open
·
If 140°C (284°F) or more: sensor circuit shorted
|
| Engine Run Time
|
Engine run time:
Min.: 0 s, Max.: 65535 s
|
Time since engine started
|
-
|
| Initial Engine Coolant Temp
|
Engine coolant temperature at engine start:
Min.: -40°C (-40°F), Max.: 119.3°C (248°F)
|
Close to ambient air temperature
|
-
|
| Initial Intake Air Temp
|
Intake air temperature at engine start:
Min.: -40°C (-40°F), Max.: 119.3°C (248°F)
|
Close to ambient air temperature
|
-
|
| Battery Voltage
|
Battery voltage:
Min.: 0 V, Max.: 65.535 V
|
11 to 14 V: Engine switch on (IG)
|
-
|
| Glow Indicator Supported
|
Status of glow indicator supported:
Supp or Unsupp
|
Unused
|
-
|
| Glow Indicator
|
Status of glow indicator:
ON or OFF
|
Unused
|
-
|
| Accelerator Position
|
Accelerator pedal position:
Min.: 0%, Max.: 399.9%
|
Actual accelerator pedal position
|
-
|
| Accel Sens. No. 1 Volt %
|
Absolute accelerator pedal position No. 1:
Min.: 0%, Max.: 100%
|
·
10 to 22%: Accelerator pedal fully released
·
52 to 90%: Accelerator pedal fully depressed
|
-
|
| Accel Sens. No. 2 Volt %
|
Absolute accelerator pedal position No. 2:
Min.: 0%, Max.: 100%
|
·
24 to 40%: Accelerator pedal fully released
·
68 to 95%: Accelerator pedal fully depressed
|
-
|
| Accel Sensor Out No. 1
|
Accelerator pedal position sensor No. 1 voltage:
Min.: 0 V, Max.: 4.98 V
|
·
0.5 to 1.1 V: Accelerator pedal fully released
·
2.6 to 4.5 V: Accelerator pedal fully depressed
|
-
|
| Accel Sensor Out No. 2
|
Accelerator pedal position sensor No. 2 voltage:
Min.: 0 V, Max.: 4.98 V
|
·
1.2 to 2.0 V: Accelerator pedal fully released
·
3.4 to 4.75 V: Accelerator pedal fully depressed
|
-
|
| Accelerator Idle Position
|
Whether or not accelerator pedal position sensor detecting idle:
ON or OFF
|
ON: Idling
|
-
|
| Accel Fully Close Learn #1
|
Accelerator fully closed learning value No. 1:
Min.: 0 deg., Max.: 124.5 deg
|
-
|
-
|
| Accel Fully Close Learn #2
|
Accelerator fully closed learning value No. 2:
Min.: 0 deg., Max.: 124.5 deg
|
-
|
-
|
| Throttle Sensor Volt %
|
Throttle valve opening percentage according to throttle position sensor:
Min.: 0%, Max.: 100%
|
·
10 to 22%: Accelerator pedal fully released
·
64 to 96%: Accelerator pedal fully depressed
|
Valve calculated based on the voltage at terminal VTA1
|
| Throttl Sensor #2 Volt %
|
Throttle valve opening percentage according to throttle position sensor No. 2:
Min.: 0 %, Max.: 100 %
|
·
42 to 62%: Accelerator pedal fully released
·
92 to 100%: Accelerator pedal fully depressed
|
Valve calculated based on the voltage at terminal VTA2
|
| ST1
|
Brake pedal signal:
ON or OFF
|
ON: Brake pedal depressed
|
-
|
| System Guard
|
System guard:
ON or OFF
|
-
|
-
|
| Open Side Malfunction
|
Open side malfunction:
ON or OFF
|
-
|
-
|
| Throttle Idle Position
|
Whether or not throttle position sensor detecting idling:
ON or OFF
|
·
ON: Accelerator pedal fully released
·
OFF: Accelerator pedal fully depressed
|
-
|
| Throttle Require Position
|
Required throttle position:
Min.: 0 V, Max.: 4.98 V
|
0.5 to 1.1 V: Idling
|
-
|
| Throttle Sensor Position*2
|
Throttle position sensor:
Min.: 0%, Max.: 100%
|
·
0%: Accelerator pedal fully released
·
50 to 80%: Accelerator pedal fully depressed
|
Recognition value for throttle opening angle on ECM
|
| Throttle Position No. 1
|
Throttle position sensor No. 1 output voltage:
Min.: 0 V, Max.: 4.98 V
|
·
0.5 to 1.1 V: Accelerator pedal fully released
·
3.2 to 4.8 V: Accelerator pedal fully depressed
·
0.6 to 1.4 V: Fail-safe operating
|
-
|
| Throttle Position No. 2
|
Throttle position sensor No. 2 output voltage:
Min.: 0 V, Max.: 4.98 V
|
·
2.1 to 3.1 V: Accelerator pedal fully released
·
4.6 to 4.98 V: Accelerator pedal fully depressed
·
2.1 to 3.1 V: Fail-safe operating
|
-
|
| Throttle Position Command
|
Throttle position command value:
Min.: 0 V, Max.: 4.98 V
|
-
|
-
|
| Throttle Sens Open Pos #1
|
Throttle sensor opener position No. 1:
Min.: 0 V, Max.: 4.98 V
|
0.6 to 1.4 V
|
-
|
| Throttle Sens Open Pos #2
|
Throttle sensor opener position No. 2:
Min.: 0 V, Max.: 4.98 V
|
1.7 to 2.5 V
|
-
|
| Throttle Motor Current
|
Throttle actuator current:
Min.: 0 A, Max.: 19.9 A
|
0 to 3.0 A: Idling
|
-
|
| Throttle Motor DUTY
|
Throttle actuator:
Min.: 0%, Max.: 100%
|
10 to 22%: Idling after engine warmed up
|
-
|
| Throttle Motor Duty (Open)
|
Throttle actuator duty ratio (open):
Min.: 0 %, Max.: 255 %
|
0 to 40%: Idling
|
-
|
| Throttle Motor Duty (Close)
|
Throttle actuator duty ratio (closed):
Min.: 0%, Max.: 255%
|
0 to 40%: Idling
|
-
|
| Throttle Fully Close Learn
|
Throttle valve fully closed
(learned value):
Min.: 0 V, Max.: 4.98 V
|
0.4 to 1.0 V: Accelerator pedal fully released
|
-
|
| +BM Voltage
|
+BM voltage:
Min.: 0 V, Max.: 79.998 V
|
11 to 14 V: Engine switch on (IG) and system normal
|
-
|
| Actuator Power Supply
|
Actuator power supply:
ON or OFF
|
ON: Idling
|
-
|
| Throttle Position
|
Throttle valve opening angle:
Min.: 0 deg, Max.: 499.99 deg
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| ISC Flow
|
Flow rate calculated from information from each sensor:
Min.: 0 L/s, Max.: 79.99 L/s
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| ISC Position
|
Target valve opening angle calculated from ISC control:
Min.: 0 deg, Max.: 499.99 deg
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| ISC Feedback Value
|
ISC feedback value:
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| ISC Learning Value
|
ISC learning value:
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Electric Load Feedback Val
|
Electrical load feedback value:
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Air Conditioner FB Val
|
Air conditioner load feedback value:
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| PS Feedback Val
|
Power steering load feedback value:
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Low Revolution Control
|
Status of low engine speed control:
ON or OFF
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Neutral Control
|
Neutral position control status for automatic transaxle:
ON or OFF
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| N Range Status
|
Judgment for shift lever neutral position:
ON or OFF
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Eng Stall Control FB Flow
|
Feedback value of intake air flow:
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Deposit Loss Flow
|
Deposit loss air flow rate:
Min.: -40 L/s, Max.: 39.99 L/s
|
0 to 6.0 L/s
|
·
This value indicates the amount of compensation for a decrease in flow passage area due to the buildup of deposits on the throttle valve.
·
Check this value for reference when the engine stalls, is difficult to start, or idles roughly.
·
When the ISC learned value is initialized by disconnecting the battery negative terminal or removing the fuses (EFI and ETC-S fuses), performing the following procedures in order to quickly relearn the Deposit Loss Flow value. After the Deposit Loss Flow has been relearned, gradual fine adjustments will continue automatically.
-
Start the engine cold and allow the engine to idle.
-
After the engine is warmed up (engine coolant temperature is above 80°C [176°F]), allow the engine to idle for an additional 5 minutes.
-
Turn the engine switch off and wait for 30 seconds.
-
Start the engine again, and allow the engine to idle for 5 minutes.
|
| Injector (Port)
|
Injection duration of No. 1 cylinder:
Min.: 0 μs., Max.: 65535 μs.
|
-
|
-
|
| Injection Volum (Cylinder 1)
|
Injection volume (Cylinder 1):
Min.: 0 ml, Max.: 2.047 ml
|
0.7 to 1.5 ml: Idling
|
Total fuel injection volume of 10 injections
|
| Fuel Pump/Speed Status
|
Fuel pump status:
ON or OFF
|
ON: Engine running
|
-
|
| Current Fuel Type
|
Current fuel type
|
Gasoline/petrol
|
-
|
| EVAP (Purge) VSV
|
Purge VSV control duty:
Min.: 0%, Max.: 100%
|
0 to 50%: Idling
|
Order signal from ECM
|
| EVAP Purge Flow
|
Ratio of evaporative purge flow to intake air volume:
Min.: 0%, Max.: 399.9%
|
0 to 4%: Idling
|
-
|
| Purge Density Learn Value
|
Learning value of purge density:
Min.: -200 Max.: 199.993
|
-
|
-
|
| EVAP Purge VSV
|
Purge VSV status:
ON or OFF
|
-
|
-
|
| Purge Cut VSV Duty
|
Purge VSV duty:
Min.: 0%, Max.: 399.9%
|
-
|
-
|
| Target Air-Fuel Ratio
|
Ratio compared to stoichiometric level:
Min.: 0, Max.: 1.99
|
0.8 to 1.2: Idling
|
·
1 = Stoichiometric air fuel ratio
|
| AF Lambda B1S1
|
Short-term fuel trim associated with bank 1 sensor 1:
Min.: -0, Max.: 1.99
|
·
Value less than 1 (0.000 to 0.999) = Rich
·
Stoichiometric air-fuel ratio = 1
·
Value greater than 1 (1.001 to 1.999) = Lean
|
-
|
| AFS Voltage B1S1
|
Air fuel ratio sensor output voltage for bank 1 sensor 1:
Min.: 0 V, Max.: 7.99 V
|
3 to 3.5 V: Idling
|
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output voltage of sensor
|
| AFS Current B1S1
|
A/F sensor output current for bank 1 sensor 1: Min.: -128 mA, Max.: 127.99 mA
|
-
|
-
|
| A/F Heater Duty B1S1
|
Air fuel ratio heater duty ratio for bank 1:
Min.: 0%, Max.: 399.9%
|
0 to 100%
|
-
|
| O2S B1S2
|
Heated oxygen sensor output voltage for bank 1 sensor 2:
Min.: 0 V, Max.: 1.275 V
|
0.1 to 0.9 V:
Driving at 70 km/h (44 mph)
|
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output voltage of sensor
|
| O2 Heater B1S2
|
Heated oxygen sensor heater for bank 1 sensor 2:
Not Act or Active
|
-
|
-
|
| O2 Heater Curr Val B1S2
|
Heated oxygen sensor heater for bank 1 sensor 2:
Min.: 0 A, Max.: 4.999 A
|
-
|
-
|
| Short FT #1
|
Short-term fuel trim:
Min.: -100%, Max.: 99.2%
|
-15 to 15%
|
Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio
|
| Long FT #1
|
Long-term fuel trim:
Min.: -100%, Max.: 99.2%
|
-15 to 15%
|
Overall fuel compensation carried out in long-term to compensate for a continual deviation of short-term fuel trim from central value
|
| Total FT #1
|
Total fuel trim value for fuel system:
Min.: -0.5, Max.: 0.496
|
-0.2 to 0.2
|
-
|
| Fuel System Status #1
|
Fuel system status:
OL or CL or OLDrive or OLFault or CLFault or Unused
|
CL: Idling after warming up
|
·
OL (Open Loop): Has not yet satisfied conditions to go closed loop
·
CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
·
OLDrive: Open loop due to driving conditions (fuel enrichment)
·
OLFault: Open loop due to detected system fault
·
CLFault: Closed loop but air fuel ratio sensor, which is used for fuel control, malfunctioning
|
| Fuel System Status #2
|
-
|
Unused
|
-
|
| IGN Advance
|
Ignition timing advance for No. 1 cylinder:
Min.: -64 deg., Max.: 63.5 deg.
|
5 to 22 deg.: Idling
(Neutral position)
|
-
|
| Knock Feedback Value
|
Knock feedback value:
Min.: -1024 deg(CA), Max.: 1023.9 deg(CA)
|
-20 to 0 deg(CA):
Driving at 70 km/h (44 mph)
|
-
|
| Knock Correct Learn Value
|
Knock correction learning value:
Min.: -1024 deg(CA), Max.: 1023.9 deg(CA)
|
0 to 20 deg(CA):
Driving at 70 km/h (44 mph)
|
-
|
| Idle Spark Advn Ctrl #1
|
Individual cylinder timing advance compensation amount (No. 1):
Min.: 0 deg(CA), Max.: 15.93 deg(CA)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Idle Spark Advn Ctrl #2
|
Individual cylinder timing advance compensation amount (No. 2):
Min.: 0 deg(CA), Max.: 15.93 deg(CA)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Idle Spark Advn Ctrl #3
|
Individual cylinder timing advance compensation amount (No. 3):
Min.: 0 deg(CA), Max.: 15.93 deg(CA)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Idle Spark Advn Ctrl #4
|
Individual cylinder timing advance compensation amount (No. 4):
Min.: 0 deg(CA), Max.: 15.93 deg(CA)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| VVT Control Status #1
|
VVT control (bank 1) status:
ON or OFF
|
-
|
-
|
| VVT Advance Fail
|
VVT control failure status:
ON or OFF
|
ON: VVT control failure
|
-
|
| VVT Aim Angle #1*1
|
VVT aim angle (bank 1):
Min.: 0%, Max.: 399.9%
|
-
|
VVT duty signal value during operation
|
| VVT Change Angle #1*1
|
VVT change angle (bank 1):
Min.: 0 DegFR, Max.: 639.9 DegFR
|
-
|
Displacement angle during operation
|
| VVT OCV Duty #1*1
|
VVT camshaft timing oil control valve operation duty:
Min.: 0%, Max.: 399.9%
|
-
|
Requested duty value for operation
|
| VN Turbo Type
|
Variable nozzle turbo type:
Not Avl or Commo or Vacuum or CAN Com
|
Not Avl (Unused)
|
-
|
| Catalyst Temp B1S1
|
Estimated catalyst temperature (bank 1, sensor 1):
Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F)
|
-
|
-
|
| Catalyst Temp B1S2
|
Estimated catalyst temperature (bank 1, sensor 2):
Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F)
|
-
|
-
|
| Starter Signal
|
Engine switch (STSW) signal:
ON or OFF
|
ON: Starter signal on
OFF: Starter signal off
|
-
|
| Starter Control
|
Starter signal status:
ON or OFF
|
ON: Cranking
|
-
|
| Power Steering Signal
|
Power steering signal:
ON or OFF
|
ON: Power steering operation
|
-
|
| Starter Relay
|
Starter relay ON or OFF
|
ON: Cranking
|
-
|
| ACC Relay
|
ACC relay ON or OFF
|
ON: Cranking
|
-
|
| Neutral Position SW Signal
|
Park/neutral position switch status:
ON or OFF
|
ON: Neutral position
|
-
|
| Stop Light Switch
|
Stop light switch:
ON or OFF
|
ON: Brake pedal depressed
|
-
|
| A/C Signal
|
Air conditioning signal:
ON or OFF
|
ON: Air conditioning ON
|
-
|
| Idle Up Signal
|
Idle up signal:
ON or OFF
|
-
|
-
|
| Closed Throttle Position SW
|
Closed throttle position switch:
ON or OFF
|
ON: Throttle fully closed
OFF: Throttle open
|
-
|
| Fuel Cut Condition
|
Fuel cut determination flag:
ON or OFF
|
-
|
-
|
| Immobiliser Communication
|
Immobiliser communication
ON or OFF
|
ON: Normal
|
-
|
| Check Mode
|
Check mode:
ON or OFF
|
ON: Check mode ON
|
See page ( )
|
| SPD Test Result
|
Check mode result for vehicle speed sensor:
Compl or Incmpl
|
-
|
-
|
| Misfire Test Result
|
Check mode result for misfire monitor:
Compl or Incmpl
|
-
|
-
|
| OXS1 Test Result
|
Check mode result for heated oxygen sensor:
Compl or Incmpl
|
-
|
-
|
| A/F Test Results #1
|
Check mode result for air fuel ratio sensor:
Compl or Incmpl
|
-
|
-
|
| Complete Parts Monitor
|
Comprehensive component monitor:
Avail or Not Avl
|
-
|
-
|
| Fuel System Monitor
|
Fuel system monitor:
Avail or Not Avl
|
-
|
-
|
| Misfire Monitor
|
Misfire monitor:
Avail or Not Avl
|
-
|
-
|
| EGR/VVT Monitor
|
EGR/VVT monitor:
Avail or Not Avl
|
-
|
-
|
| EGR/VVT Monitor
|
EGR/VVT monitor:
Compl or Incmpl
|
-
|
-
|
| O2S (A/FS) Heater Monitor
|
O2S (A/FS) heater monitor/
Not Avl or Avail
|
-
|
-
|
| O2S (A/FS) Heater Monitor
|
O2S (A/FS) heater monitor/
Compl or Incmpl
|
-
|
-
|
| O2S (A/FS) Monitor
|
O2S (A/FS) monitor:
Avail or Not Avl
|
-
|
-
|
| O2S (A/FS) Monitor
|
O2S (A/FS) monitor:
Compl or Incmpl
|
-
|
-
|
| A/C Monitor
|
A/C monitor/
Not Avl or Avail
|
-
|
-
|
| A/C Monitor
|
A/C monitor/
Compl or Incmpl
|
-
|
-
|
| 2nd Air Monitor
|
2nd air monitor/
Not Avl or Avail
|
-
|
-
|
| 2nd Air Monitor
|
2nd air monitor/
Compl or Incmpl
|
-
|
-
|
| EVAP Monitor
|
EVAP monitor
Not Avl or Avail
|
-
|
-
|
| EVAP Monitor
|
EVAP monitor
Compl or Incmpl
|
-
|
-
|
| Heated Catalyst Monitor
|
Heated catalyst monitor/
Not Avl or Avail
|
-
|
-
|
| Heated Catalyst Monitor
|
Heated catalyst monitor/
Compl or Incmpl
|
-
|
-
|
| Catalyst Monitor
|
Catalyst monitor:
Avail or Not Avl
|
-
|
-
|
| Catalyst Monitor
|
Catalyst monitor:
Compl or Incmpl
|
-
|
-
|
| TC Terminal
|
TC terminal status:
ON or OFF
|
-
|
-
|
| # Codes (Include History)
|
Number of codes:
Min.: 0, Max.: 255
|
-
|
Number of detected DTCs
|
| MIL
|
MIL status:
ON or OFF
|
ON: MIL ON
|
-
|
| MIL ON Run Distance
|
Distance traveled since MIL turned ON:
Min.: 0 Km, Max.: 65535 Km
|
Distance since DTC detected
|
-
|
| Running Time from MIL ON
|
Running time since MIL turned ON:
Min.: 0 min, Max.: 65535 min
|
Equivalent to running time since MIL turned ON
|
-
|
| Time after DTC Cleared
|
Time since DTCs cleared:
Min.: 0 min, Max.: 65535 min
|
Equivalent to time since DTCs cleared
|
-
|
| Distance from DTC Cleared
|
Distance traveled since DTCs cleared:
Min.: 0 km, Max.: 65535 km
|
Equivalent to distance driven since DTCs cleared
|
-
|
| Warmup Cycle Cleared DTC
|
Warm-up cycles since DTCs cleared:
Min.: 0, Max.: 255
|
-
|
Number of warm-up cycles since DTCs cleared
|
| Dist Batt Cable Disconnect
|
Distance after battery cable disconnected:
Min.: 0 km, Max.: 65535 km
|
Total distance vehicle driven after battery cable disconnected
|
-
|
| IG OFF Elapsed Time
|
Time after engine switch off
Min.: 0 min, Max.: 655350 min
|
Cumulative time after engine switch off
|
-
|
| OBD Requirements
|
OBD requirements
|
EOBD (Euro-OBD)
|
-
|
| Number of Emission DTC
|
Number of emission DTCs
|
-
|
-
|
| TC and TE1
|
TC and CG (TE1) terminals of DLC3:
ON or OFF
|
-
|
-
|
| Ignition Trig. Count
|
Ignition counter:
Min.: 0, Max.: 65535
|
0 to 400
|
-
|
| Cylinder #1 Misfire Count
|
Misfire count of cylinder 1:
Min.: 0, Max.: 255
|
0: Normal
|
-
|
| Cylinder #2 Misfire Count
|
Misfire count of cylinder 2:
Min.: 0, Max.: 255
|
0: Normal
|
-
|
| Cylinder #3 Misfire Count
|
Misfire count of cylinder 3:
Min.: 0, Max.: 255
|
0: Normal
|
-
|
| Cylinder #4 Misfire Count
|
Misfire count of cylinder 4:
Min.: 0, Max.: 255
|
0: Normal
|
-
|
| All Cylinders Misfire Count
|
Misfire count of all cylinders:
Min.: 0, Max.: 255
|
0: Normal
|
-
|
| Misfire RPM
|
Engine speed when misfire occurs:
Min.: 0 rpm, Max.: 6375 rpm
|
0 rpm: Normal
|
-
|
| Misfire Load
|
Engine load when misfire occurred:
Min.: 0 g/rev, Max.: 3.98 g/rev
|
-
|
-
|
| Misfire Margin
|
Margin to detect engine misfire
Min.: -127%, Max.: 127%
|
0 to 127%: Idling
|
Misfire detection margin
|
| Engine Speed (Starter Off)
|
Engine speed when starter off:
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Starter Count
|
Number of times starter turned on after engine switch turned from off to on (IG):
Min.: 0, Max.: 255
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Run Dist of Previous Trip
|
Distance traveled during previous trip:
Min.: 0 km, Max.: 655.35 km
|
-
|
·
Run Dist of Previous Trip continues to display the distance traveled in the previous trip during the detection period of DTC P1604, which ends 5 seconds after the engine starts.
Then the previous trip distance will be cleared and the distance traveled during this trip, which is calculated based on the vehicle speed, will be displayed.
·
When the engine is difficult to start and DTC P1604 is stored, Run Dist of Previous Trip will continue to be displayed.
When inspecting for DTCs other than P1604, or when taking a snapshot, the distance traveled during this trip will be displayed.
|
| Engine Starting Time
|
Engine run time (elapsed time from engine switch on (IG) to off):
Min.: 0 ms, Max.: 655350 ms
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Previous Trip Coolant Temp
|
Coolant temperature of previous trip:
Min.: -40°C (-40°F), Max.: 215°C (419°F)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Previous Trip Intake Temp
|
Intake air Coolant temperature of previous trip:
Min.: -40°C (-40°F), Max.: 215°C (419°F)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Engine Oil Temperature
|
Engine oil temperature (estimated):
Min.: -40°C (-40°F), Max.: 215°C (419°F)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Previous Trip Eng Oil Temp
|
Engine oil temperature of previous trip (estimated):
Min.: -40°C (-40°F), Max.: 215°C (419°F)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Ambient Temp for A/C
|
Ambient temperature:
Min.: -40°C (-40°F), Max.: 215°C (419°F)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Previous Trip Ambient Temp
|
Ambient temperature of previous trip:
Min.: -40°C (-40°F), Max.: 215°C (419°F)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Engine Start Hesitation
|
History of instances of slow engine starts:
ON or OFF
|
-
|
-
|
| Low Rev for Eng Start
|
History of low engine speed after engine starts:
ON or OFF
|
-
|
-
|
| Minimum Engine Speed
|
Minimum engine speed:
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Battery Current
|
Battery current/
Min.: -125 A, Max.: 124.9 A
|
-
|
-
|
| Battery Temperature
|
Battery temperature/
Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
|
-
|
-
|
| Alternator Output Duty
|
Generator output duty/
Min.: 0%, Max.: 399.9%
|
-
|
Electricity generated by alternator is output through duty ratio charging control service data
|
| Alt Vol - Non Active Test
|
Request voltage when regulator not under forced activation/
Min.: 0 V, Max.: 79.998 V
|
Battery electrolyte temperature varies (12.5 to 14.8 V) while driving: After engine start
|
Alternator regulator output voltage is output when performing Active Test, value is 0 V
|
| Alt Vol - Active Test
|
Request voltage when regulator under forced activation/
Min.: 0 V, Max.: 79.998 V
|
Request instruction voltage value: After engine start
|
Charging control service data When not performing Active Test, value is 0 V
|
| Electric Fan Motor
|
Electric fan motor:
ON or OFF
|
-
|
-
|
| Brake Override System
|
Brake override system status:
ON or OFF
|
ON: Brake override system operating
|
-
|
| Idle Fuel Cut
|
Fuel cut idle:
ON or OFF
|
ON: Fuel cut operating
|
-
|
| FC TAU
|
Fuel cut TAU (Fuel cut with very light load):
ON or OFF
|
ON: Fuel cut operating
|
Fuel cut being performed during very light load to prevent incomplete engine combustion
|
| Immobiliser Fuel Cut
|
Status of the immobiliser fuel cut:
ON or OFF
|
-
|
-
|
| Electrical Load Signal 1
|
Status of electrical load signal:
ON or OFF
|
ON: Electrical signal on
|
-
|
| Electrical Load Signal 2
|
Electrical load signal:
ON or OFF
|
-
|
-
|
| Electrical Load Signal 3
|
Electrical load signal:
ON or OFF
|
-
|
-
|
| Model Code
|
Identifies model code
|
ACR5#
|
-
|
| Engine Type
|
Identifies engine type
|
2AZFE
|
-
|
| Cylinder Number
|
Identifies number of cylinders
Min.: 0, Max.: 255
|
4
|
-
|
| Transmission Type
|
Identifies transmission type
|
CVT
|
-
|
| Destination
|
Identifies destination
|
W
|
-
|
| Model Year
|
Identifying model year:
Min.: 1900, Max.: 2155
|
20##
|
-
|
| System Identification
|
System identification
|
Gasoline (gasoline engine)
|
-
|
| Engine Speed of Cyl #1
|
Engine speed during No. 1 cylinder fuel cut:
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
|
| Engine Speed of Cyl #2
|
Engine speed during No. 2 cylinder fuel cut:
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
|
| Engine Speed of Cyl #3
|
Engine speed during No. 3 cylinder fuel cut:
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
|
| Engine Speed of Cyl #4
|
Engine speed during No. 4 cylinder fuel cut:
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
|
| Av Engine Speed of All Cyl
|
Average of engine speed values during fuel cut of No. 1 to No. 4 cylinder:
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
|