Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › 2014.09–2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P2610  ECM / PCM Internal Engine Off Timer Performance  


DESCRIPTION

The soak timer is built into the ECM. While the engine is running, the ECM monitors the synchronization of the soak timer and the CPU clock. If these two are not synchronized, the ECM will interpret this as a malfunction, illuminate the MIL and store this DTC.

DTC No. DTC Detection Condition Trouble Area
P2610 ECM internal malfunction (2 trip detection logic). ECM

A216661E13
4.484,0.575 4.883,0.731 0.399,0.156 10 IGSW 5.643,3.746 6.007,3.902 0.364,0.156 10 ECM 5.179,0.689 5.911,0.997 0.732,0.309 10 Soak Timer IC 5.207,2.018 5.868,2.346 0.661,0.328 10 Power Source IC 5.172,2.81 5.911,3.132 0.739,0.323 10 Main Relay Control IC 3.778,0.603 4.115,0.754 0.337,0.151 10 IGN 4.695,2.369 4.920,2.538 0.225,0.170 10 +B 4.485,3.174 4.919,3.330 0.434,0.156 10 MREL 2.68,1.145 2.961,1.301 0.281,0.156 10 IG2 0.45,1.591 1.137,1.754 0.687,0.163 10 IG2 1.027,2.747 1.599,2.903 0.573,0.156 10 FL MAIN 1.027,2.299 1.729,2.454 0.702,0.156 10 F/B BATT 1.179,3.335 2.272,3.505 1.093,0.170 10 Auxiliary Battery 3.195,3.354 4.013,3.510 0.818,0.156 10 EFI MAIN 2.26,2.791 2.556,3.003 0.296,0.211 10 EFI 1.433,0.841 1.825,0.997 0.392,0.156 10 IG2D 0.787,1.152 1.866,1.331 1.079,0.179 10 Main Body ECU

CAUTION / NOTICE / HINT

HINT:
·

DTC P2610 is set if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is required.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

NEXT

2.CHECK WHETHER DTC OUTPUT RECURS (DTC P2610)
2.CHECK WHETHER DTC OUTPUT RECURS (DTC P2610)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Start the engine and wait for 10 minutes or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


g.

If no pending DTC is displayed, the repair has been successfully completed.



NEXT

END