DESCRIPTION
The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
If it is impossible to replicate the problem even though a DTC is detected, confirm the freeze frame data.
The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the GTS, 5 separate sets of freeze frame data, including the data values at the time when the DTC was set, can be checked.
3 data sets before the DTC was stored.
1 data set when the DTC was stored.
1 data set after the DTC was stored.
These data sets can be used to simulate the condition of the vehicle around the time of the occurrence the malfunction. The data may assist in identifying the cause of the malfunction, and judging whether it was temporary or not.
LIST OF FREEZE FRAME DATA
| LABEL
(Tester Display) |
Measurement Item | Diagnostic Note |
|---|---|---|
| Vehicle Speed | Vehicle speed | Speed indicated on speedometer |
| Engine Speed | Engine speed | - |
| Calculate Load | Calculated load | Calculated load by ECM |
| Vehicle Load | Vehicle load | - |
| MAF | Mass air flow volume | If approximately 0.0 gm/sec.:
·
Mass air flow meter power source circuit open or shorted ·
VG circuit open or shorted If 271.0 gm/sec. or more : ·
E2G circuit open |
| Atmosphere Pressure | Atmospheric pressure | - |
| Coolant Temp | Engine coolant temperature | If -40°C (-40°F), sensor circuit open
If 140°C (284°F) or more, sensor circuit shorted |
| Intake Air | Intake air temperature | If -40°C (-40°F), sensor circuit open
If 140°C (284°F) or more, sensor circuit shorted |
| Engine Run Time | Accumulated engine running time | - |
| Initial Engine Coolant Temp | Engine coolant temperature at engine start | - |
| Initial Intake Air Temp | Intake air temperature at engine start | - |
| Battery Voltage | Battery voltage | - |
| Glow Indicator Supported | Glow indicator supported | Unused |
| Glow Indicator | Glow indicator status | Unused |
| Accel Sens. No. 1 Volt % | Absolute accelerator pedal position No. 1 | - |
| Accel Sens. No. 2 Volt % | Absolute accelerator pedal position No. 2 | - |
| Throttle Sensor Volt % | Absolute throttle position sensor No. 1 | - |
| Throttl Sensor #2 Volt % | Absolute throttle position sensor No. 2 | - |
| Throttle Sensor Position | Throttle sensor position | - |
| Throttle Motor DUTY | Throttle actuator | - |
| Throttle Position | Throttle valve opening angle | When the engine stalls, is difficult to start, or idles roughly. |
| ISC Flow | Flow rate calculated using information from MAF meter | When the engine stalls, is difficult to start, or idles roughly. |
| ISC Position | Requested opening amount calculated using ISC | When the engine stalls, is difficult to start, or idles roughly. |
| ISC Feedback Value | ISC feedback compensation amount | When the engine stalls, is difficult to start, or idles roughly. |
| ISC Learning Value | ISC learned compensation amount | When the engine stalls, is difficult to start, or idles roughly. |
| Electric Load Feedback Val | Compensation flow rate according to electrical load | When the engine stalls, is difficult to start, or idles roughly. |
| Air Conditioner FB Val | Compensation flow rate according to air conditioner load | When the engine stalls, is difficult to start, or idles roughly. |
| PS Feedback Val | Compensation flow rate according to power steering load | When the engine stalls, is difficult to start, or idles roughly. |
| Low Revolution Control | Low engine speed control operation state | When the engine stalls, is difficult to start, or idles roughly. |
| Neutral Control | Neutral control operation state | When the engine stalls, is difficult to start, or idles roughly. |
| N Range Status | Shift lever N status | When the engine stalls, is difficult to start, or idles roughly. |
| Eng Stall Control FB Flow | Intake air compensation flow rate | When the engine stalls, is difficult to start, or idles roughly. |
| Deposit Loss Flow | Flow loss due to deposits | When the engine stalls, is difficult to start, or idles roughly. |
| Injector (Port) | Injection period of No. 1 cylinder | - |
| Injection Volum (Cylinder 1) | Injection volume | - |
| Fuel Pump/Speed Status | Fuel pump status | - |
| Current Fuel Type | Current fuel type | - |
| EVAP (Purge) VSV | Purge VSV duty ratio | - |
| Evap Purge Flow | Purge flow | - |
| Purge Density Learn Value | Learning value of purge density | - |
| EVAP Purge VSV | Purge VSV | - |
| Purge Cut VSV Duty | Purge VSV duty | - |
| Target Air-Fuel Ratio | Ratio to stoichiometric level | - |
| AF Lambda B1S1 | Fuel trim at air fuel ratio sensor | - |
| AFS Voltage B1S1 | Air fuel ratio sensor (sensor 1) output | - |
| AFS Current B1S1 | Air fuel ratio sensor output current | - |
| A/F Heater Duty B1S1 | Air fuel ratio heater duty ratio (bank 1 sensor 1) | - |
| O2S B1S2 | Heated oxygen sensor (sensor 2) output | - |
| O2 Heater B1S2 | Heated oxygen sensor heater (Bank 1 Sensor 2) | - |
| O2S Heater Curr Val B1S2 | Heated oxygen sensor current (Bank 1 Sensor 2) | - |
| Short FT #1 | Short-term fuel trim | Short-term fuel compensation used to maintain air fuel ratio at stoichiometric |
| Long FT #1 | Long-term fuel trim | Overall fuel compensation carried out in long-term to compensate for a continual deviation of short-term fuel trim from central value |
| Total FT #1 | Total fuel trim | - |
| Fuel System Status #1 | Fuel system status (bank 1) | ·
OL (Open Loop): Has not yet satisfied conditions to go closed loop ·
CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control ·
OLDrive: Open loop due to driving conditions (fuel enrichment) ·
OLFault: Open loop due to detected system fault ·
CLFault: Closed loop but air fuel ratio sensor, which is used for fuel control, malfunctioning |
| Fuel System Status #2 | Fuel system status (bank 2) | Not available |
| IGN Advance | Ignition advance | - |
| Knock Feedback Value | Feedback value of knocking | - |
| Knock Correct Learn Value | Correction learning value of knocking | - |
| Idle Spark Advn Ctrl #1 | Individual cylinder timing advance compensation amount (No. 1) | When the engine stalls, is difficult to start, or idles roughly. |
| Idle Spark Advn Ctrl #2 | Individual cylinder timing advance compensation amount (No. 2) | When the engine stalls, is difficult to start, or idles roughly. |
| Idle Spark Advn Ctrl #3 | Individual cylinder timing advance compensation amount (No. 3) | When the engine stalls, is difficult to start, or idles roughly. |
| Idle Spark Advn Ctrl #4 | Individual cylinder timing advance compensation amount (No. 4) | When the engine stalls, is difficult to start, or idles roughly. |
| Actual VVT Angle #1 | VVT displacement angle for bank 1 | - |
| VVT Control Status #1 | VVT control status (bank 1) | - |
| VVT Advance Fail | VVT control failure status | - |
| Catalyst Temp B1S1 | Estimated catalyst temperature (sensor 1) | - |
| Catalyst Temp B1S2 | Estimated catalyst temperature (sensor 2) | - |
| Starter Signal | Starter switch (STSW) signal | - |
| Starter Control | Starter control | - |
| Power Steering Signal | Power steering signal (history) | Signal status usually ON until engine switch is turned off |
| Starter Relay | Starter relay operation | - |
| ACC Relay | ACC relay operation | - |
| Neutral Position SW Signal | Park/neutral position switch signal | - |
| Stop Light Switch | Stop light switch | - |
| A/C Signal | Air conditioning signal | - |
| Idle Up Signal | Idle up signal status | - |
| Closed Throttle Position SW | Closed throttle position switch | - |
| Fuel Cut Condition | Fuel cut condition | - |
| Immobiliser Communication | Immobiliser communication | - |
| TC Terminal | TC terminal status | - |
| Time after DTC Cleared | Cumulative time after DTC cleared | - |
| Distance from DTC Cleared | Accumulated distance after DTC cleared | - |
| IG OFF Elapsed Time | Time after engine switch off | - |
| Warmup Cycle Cleared DTC | Warm-up cycle after DTC cleared | - |
| Dist Batt Cable Disconnect | Total distance vehicle driven after battery cable disconnected | - |
| TC and TE1 | TC and TE1 terminals of DLC3 | - |
| Ignition Trig. Count | Ignition counter | - |
| Cylinder #1 Misfire Count | Cylinder #1 misfire count | - |
| Cylinder #2 Misfire Count | Cylinder #2 misfire count | - |
| Cylinder #3 Misfire Count | Cylinder #3 misfire count | - |
| Cylinder #4 Misfire Count | Cylinder #4 misfire count | - |
| All Cylinders Misfire Count | All cylinder misfire count | - |
| Misfire RPM | Engine speed when misfire occurs | - |
| Misfire Load | Engine load when misfire occurs | - |
| Misfire Margin | Margin to detect engine misfire | - |
| Engine Speed (Starter Off) | Engine speed when starter off | When the engine stalls, is difficult to start, or idles roughly. |
| Starter Count | Number of times starter turned on after engine switch on (IG) | When the engine stalls, is difficult to start, or idles roughly. |
| Run Dist of Previous Trip | Distance driven during previous trip | ·
Run Dist of Previous Trip continues to display the distance traveled in the previous trip during the detection period of DTC P1604, which ends 5 seconds after the engine starts. Then the previous trip distance will be cleared and the distance traveled during this trip, which is calculated based on the vehicle speed, will be displayed. ·
When the engine is difficult to start and DTC P1604 is stored, Run Dist of Previous Trip will continue to be displayed. When inspecting for DTCs other than P1604, or when taking a snapshot, the distance traveled during this trip will be displayed. |
| Engine Starting Time | Time elapsed after engine started (interval between engine switch on (IG) and off) | When the engine stalls, is difficult to start, or idles roughly. |
| Previous Trip Coolant Temp | Engine coolant temperature during previous trip | When the engine stalls, is difficult to start, or idles roughly. |
| Previous Trip Intake Temp | Intake air temperature during previous trip | When the engine stalls, is difficult to start, or idles roughly. |
| Engine Oil Temperature | Engine oil temperature (estimated temperature) | When the engine stalls, is difficult to start, or idles roughly. |
| Previous Trip Eng Oil Temp | Engine oil temperature during previous trip | When the engine stalls, is difficult to start, or idles roughly. |
| Ambient Temp for A/C | Ambient temperature for A/C | When the engine stalls, is difficult to start, or idles roughly. |
| Previous Trip Ambient Temp | Ambient temperature during previous trip | When the engine stalls, is difficult to start, or idles roughly. |
| Engine Start Hesitation | History of hesitation during engine start | - |
| Low Rev for Eng Start | History of low engine speed after engine start | - |
| Minimum Engine Speed | Minimum engine speed | When the engine stalls, is difficult to start, or idles roughly. |
| Battery Current | Battery current | - |
| Battery Temperature | Battery temperature | - |
| Alternator Output Duty | Generator output duty | - |
| Alt Vol - Non Active Test | Request voltage when regulator not under forced activation | - |
| Alt Vol - Active Test | Request voltage when regulator under forced activation | - |
| Electric Fan Motor | Electric fan motor | - |
| Brake Override System | Brake override system status | - |
| Idle Fuel Cut | Idle fuel cut | - |
| FC TAU | Fuel cut with very light load | Fuel cut being performed with very light load to prevent incomplete engine combustion |
| Immobiliser Fuel Cut | Status of the immobiliser fuel cut | - |
| Electrical Load Signal 1 | Electrical load signal | - |
| Electrical Load Signal 2 | Electrical load signal | - |
| Electrical Load Signal 3 | Electrical load signal | - |
| Tester Display | Measurement Item | Diagnostic Note |
|---|---|---|
| Vehicle Speed | Vehicle speed | Speed indicated on speedometer |
| Engine Speed | Engine speed | - |
| Calculate Load | Calculated load | Calculated load by ECM |
| MAF | Mass air flow volume | If approximately 0.0 gm/sec:
·
Mass air flow meter power source circuit open or shorted ·
VG circuit open or shorted If value 271.0 gm/sec or more: ·
E2G circuit open |
| Atmosphere Pressure | Atmospheric pressure | - |
| Coolant Temp | Engine coolant temperature | If -40°C (-40°F), sensor circuit open
If 140°C (284°F) or more, sensor circuit shorted |
| Intake Air | Intake air temperature | If -40°C (-40°F), sensor circuit open
If 140°C (284°F) or more, sensor circuit shorted |
| Engine Run Time | Accumulated engine running time | - |
| Initial Engine Coolant Temp | Engine coolant temperature at engine start | - |
| Initial Intake Air Temp | Intake air temperature at engine start | - |
| Battery Voltage | Battery voltage | - |
| Accel Sens. No. 1 Volt % | Absolute accelerator pedal position No. 1 | - |
| Accel Sens. No. 2 Volt % | Absolute accelerator pedal position No. 2 | - |
| Throttle Sensor Volt % | Absolute throttle position sensor No. 1 | - |
| Throttl Sensor #2 Volt % | Absolute throttle position sensor No. 2 | - |
| Throttle Sensor Position | Throttle sensor position | - |
| Throttle Motor DUTY | Throttle actuator | - |
| Throttle Position | Throttle valve opening angle | When the engine stalls, is difficult to start, or idles roughly. |
| ISC Flow | Flow rate calculated using information from MAF meter | When the engine stalls, is difficult to start, or idles roughly. |
| ISC Position | Requested opening amount calculated using ISC | When the engine stalls, is difficult to start, or idles roughly. |
| ISC Feedback Value | ISC feedback compensation amount | When the engine stalls, is difficult to start, or idles roughly. |
| ISC Learning Value | ISC learned compensation amount | When the engine stalls, is difficult to start, or idles roughly. |
| Electric Load Feedback Val | Compensation flow rate according to electrical load | When the engine stalls, is difficult to start, or idles roughly. |
| Air Conditioner FB Val | Compensation flow rate according to air conditioner load | When the engine stalls, is difficult to start, or idles roughly. |
| Low Revolution Control | Low engine speed control operation state | When the engine stalls, is difficult to start, or idles roughly. |
| N Range Status | Shift lever N status | When the engine stalls, is difficult to start, or idles roughly. |
| Deposit Loss Flow | Flow loss due to deposits | When the engine stalls, is difficult to start, or idles roughly. |
| Injector (Port) | Injection period of No. 1 cylinder | - |
| Injection Volum (Cylinder 1) | Injection volume | - |
| Fuel Pump/Speed Status | Fuel pump status | - |
| EVAP (Purge) VSV | Purge VSV duty ratio | - |
| Evap Purge Flow | Purge flow | - |
| Purge Density Learn Value | Learning value of purge density | - |
| EVAP Purge VSV | Purge VSV | - |
| Target Air-Fuel Ratio | Ratio to stoichiometric level | - |
| AF Lambda B1S1 | Fuel trim at air fuel ratio sensor | - |
| AFS Voltage B1S1 | Air fuel ratio sensor output voltage | - |
| AFS Current B1S1 | Air fuel ratio sensor output current | - |
| O2S B1S2 | Heated oxygen sensor output voltage | - |
| Short FT #1 | Short-term fuel trim | Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio |
| Long FT #1 | Long-term fuel trim | Overall fuel compensation carried out in long-term to compensate for a continual deviation of short-term fuel trim from central value |
| Fuel System Status #1 | Fuel system status (bank 1) | ·
OL (Open Loop): Has not yet satisfied conditions to go closed loop ·
CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control ·
OLDrive: Open loop due to driving conditions (fuel enrichment) ·
OLFault: Open loop due to detected system fault ·
CLFault: Closed loop but air fuel ratio sensor, which is used for fuel control, malfunctioning |
| Fuel System Status #2 | Fuel system status (bank 2) | Not available |
| IGN Advance | Ignition advance | - |
| Knock Feedback Value | Feedback value of knocking | - |
| Knock Correct Learn Value | Correction learning value of knocking | - |
| Idle Spark Advn Ctrl #1 | Individual cylinder timing advance compensation amount (No. 1) | When the engine stalls, is difficult to start, or idles roughly. |
| Idle Spark Advn Ctrl #2 | Individual cylinder timing advance compensation amount (No. 2) | When the engine stalls, is difficult to start, or idles roughly. |
| Idle Spark Advn Ctrl #3 | Individual cylinder timing advance compensation amount (No. 3) | When the engine stalls, is difficult to start, or idles roughly. |
| Idle Spark Advn Ctrl #4 | Individual cylinder timing advance compensation amount (No. 4) | When the engine stalls, is difficult to start, or idles roughly. |
| VVT Control Status #1 | VVT control status (bank 1) | - |
| VVT Advance Fail | VVT control failure status | - |
| Starter Signal | Starter signal | - |
| Starter Control | Starter control | - |
| Power Steering Signal | Power steering signal | - |
| Starter Relay | Starter relay operation | - |
| Power Steer. Sig. Record | Power steering signal | - |
| ACC Relay | ACC relay operation | - |
| Neutral Position SW Signal | Park/neutral position switch signal | - |
| Stop Light Switch | Stop light switch | - |
| A/C Signal | Air conditioning signal | - |
| Closed Throttle Position SW | Closed throttle position switch | - |
| Electrical Load Signal | Electrical load signal | - |
| Time after DTC Cleared | Cumulative time after DTC cleared | - |
| Distance from DTC Cleared | Accumulated distance after DTC cleared | - |
| Warmup Cycle Cleared DTC | Warm-up cycle after DTC cleared | - |
| TC and TE1 | TC and TE1 terminals of DLC3 | - |
| Engine Starting Time | Time elapsed after engine started (interval between engine switch on (IG) and off) | When the engine stalls, is difficult to start, or idles roughly. |
| Engine Speed (Starter Off) | Engine speed when starter off | When the engine stalls, is difficult to start, or idles roughly. |
| Starter Count | Number of times starter turned on after engine switch on (IG) | ·
Indicates the number of times starter turned ON in the current driving cycle. ·
Number of times starter turned ON before engine started displayed in the 1 position. ·
Number of times starter turned ON after engine started displayed in the 10 position. Example: If "21" is displayed on the Techstream, the starter was turned ON 1 time before engine start and turned ON 2 times after engine start. (The maximum value for each counter is 9 times before engine start and 11 times after engine start) |
| Run Dist of Previous Trip | Distance driven during previous trip | ·
Run Dist of Previous Trip continues to display the distance traveled in the previous trip during the detection period of DTC P1604, which ends 5 seconds after the engine starts. Then the previous trip distance will be cleared and the distance traveled during this trip, which is calculated based on the vehicle speed, will be displayed. ·
When the engine is difficult to start and DTC P1604 is stored, Run Dist of Previous Trip will continue to be displayed. When inspecting for DTCs other than P1604, or when taking a snapshot, the distance traveled during this trip will be displayed. |
| Previous Trip Coolant Temp | Engine coolant temperature during previous trip | When the engine stalls, is difficult to start, or idles roughly. |
| Previous Trip Intake Temp | Intake air temperature during previous trip | When the engine stalls, is difficult to start, or idles roughly. |
| Engine Oil Temperature | Engine oil temperature (estimated temperature) | When the engine stalls, is difficult to start, or idles roughly. |
| Previous Trip Eng Oil Temp | Engine oil temperature during previous trip | When the engine stalls, is difficult to start, or idles roughly. |
| Ambient Temp for A/C | Ambient temperature for A/C | When the engine stalls, is difficult to start, or idles roughly. |
| Previous Trip Ambient Temp | Ambient temperature during previous trip | When the engine stalls, is difficult to start, or idles roughly. |
| Engine Start Hesitation | History of hesitation during engine start | - |
| Low Rev for Eng Start | History of low engine speed after engine start | - |
| Minimum Engine Speed | Minimum engine speed | When the engine stalls, is difficult to start, or idles roughly. |
| Electric Fan Motor | Electric fan motor (cooling fan motor) | - |
| Idle Fuel Cut | Idle fuel cut | - |
| FC TAU | Fuel cut with very light load | Fuel cut being performed with very light load to prevent incomplete engine combustion |
| Immobiliser Fuel Cut | Status of the immobiliser fuel cut | - |