Home › Engine / Hybrid System › 2AZ-FE FUEL › FUEL INJECTOR
RM24M0E _51 Engine / Hybrid System _059542 2AZ-FE FUEL _0291796 FUEL INJECTOR G

2AZ-FE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

a.
A116182

Measure the resistance between the injector terminals.

Standard resistance:

11.6 to 12.4 Ω at 20°C (68°F)


If the result is not as specified, replace the injector.


b.

Inspect the injector injection.

CAUTION:

Keep the injector away from sparks during the test.


i.
A264971E18
0.51,1.646 0.635,2 0.635,2 0.729,2 false 0.75,0.938 0.938,0.302 0.938,0.302 1.063,0.302 false 2.26,1.771 1.792,1.469 1.792,1.469 1.781,1.26 false 2.802,1.094 2.802,0.844 false 2.292,1.719 2.5,1.906 0.208,0.188 10 false *c 1.177,0.24 2.156,0.406 0.979,0.167 10 false *b 0.833,1.938 1.115,2.083 0.281,0.146 10 false *a 2.74,1.146 3.021,1.323 0.281,0.177 10 false *d

Install the fuel tube connector to SST (hose). Then connect the tube connector to the fuel pipe (vehicle side).

Text in Illustration
*a SST (Hose)
*b SST (Hose Band)
*c SST (Fuel Tube Connector)
*d Fuel Pipe (Vehicle Side)

SST
09268-31014  (09268-41500, 09268-41700, 95336-08070)


ii.

Install the O-ring to the fuel injector.


iii.
A264972E15
1,0.146 1.333,0.146 false 0.99,1.906 1.323,1.906 false 0.969,0.76 1.302,0.76 false 1.49,1.021 1.708,1.021 false 2.115,1.354 2.448,1.354 false 1.719,0.333 2.052,0.333 false 0.802,0.073 1.042,0.271 0.24,0.198 10 false *a 0.802,0.667 1.042,0.865 0.24,0.198 10 false *c 2.104,0.26 2.344,0.458 0.24,0.198 10 false *b 0.823,1.813 1.063,2.01 0.24,0.198 10 false *e 1.729,0.938 1.969,1.135 0.24,0.198 10 false *1 2.49,1.292 2.729,1.49 0.24,0.198 10 false *d

Connect SST (adapter and hose) to the injector, and hold the injector and union with SST (clamp).

Text in Illustration
*1 O-ring
*a SST (Hose)
*b SST (Hose Band)
*c SST (Adapter)
*d SST (Clamp)
*e Vinyl Tube

SST
09268-31014  (09268-41110, 09268-41300, 09268-41700, 95336-08070)


iv.

Put the injector into the graduated cylinder.

CAUTION:

Install a suitable vinyl tube onto the injector to contain gasoline spray.



v.

Operate the fuel pump.


vi.
A264973E19
2.042,0.542 2.042,0.958 false 1.99,0.99 2.146,1.229 0.156,0.24 10 false *a 1.031,1.354 1.188,1.594 0.156,0.24 10 false *b

Connect SST (wire) to the injector and the battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each injector 2 or 3 times.

Text in Illustration
*a SST (Wire)
*b Connect

SST
09842-30080  

Standard injection volume:

76 to 92 cm3 (4.6 to 5.6 cu in.) per 15 seconds


Standard difference between each injector:

16 cm3 (1.0 cu in.) or less




c.
A116184

Inspect the fuel leakage.

i.

Disconnect the SST (wire) tester probes from the battery and check the fuel leakage from the injector.

Standard fuel drop:

1 drop or less per 12 minutes



ii.

Turn the ignition switch off.


iii.

Remove SST.


iv.

Disconnect the intelligent tester from the DLC3.


v.

Reconnect the fuel inlet hose (rear fuel pipe) to the fuel main tube.