Home › Engine / Hybrid System › 2AZ-FE FUEL › FUEL TANK
RM24M0E _51 Engine / Hybrid System _059542 2AZ-FE FUEL _0291800 FUEL TANK A

2AZ-FE FUEL  FUEL TANK  REASSEMBLY  


PROCEDURE

Hide 77651B 1.INSTALL FUEL TANK CUSHION

a.
A131618

Install 6 new fuel tank cushions onto the fuel tank as shown in the illustration.


Hide 77512 2.INSTALL REAR FUEL TANK BRACKET

a.
A131616

Install the bracket with the 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 77641A 3.INSTALL NO. 1 FUEL TANK PROTECTOR

a.
A131617

Install the protector with the 2 nuts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 77020A 4.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

a.
A126811E02
2.04,0.463 2.176,0.698 false 2.173,0.698 2.389,0.698 false 2.417,0.609 3.214,0.762 0.796,0.153 10 New Gasket

Install a new gasket onto the fuel pump.


b.
A135879

Connect the fuel hose and install the fuel pump into the fuel tank.

NOTICE:
·

When connecting the fuel hose, make sure the fuel hose marking faces upward, and make sure the grip part of the clamp faces the front of the vehicle.


·

Be careful not to bend the arm of the fuel sender gauge.


·

When connecting the fuel hose, do not forcibly pull the hose.




Hide 77168A 5.INSTALL FUEL TANK VENT TUBE SET PLATE

a.
A135880E02
1.323,1.417 1.031,1.833 false 1.031,1.833 0.896,1.833 false 1.375,1.365 1.531,1.104 false 1.531,1.104 1.615,1.104 false 0.073,1.74 0.74,2.021 0.667,0.281 10 true Protrusion 1.635,1.01 2.115,1.354 0.479,0.344 10 true Groove

Install the set plate with the 8 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

HINT:

Align the protrusion of the set plate with the groove of the fuel pump.



Hide 77027 6.INSTALL NO. 2 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A135881E02
2.573,1.281 2.771,1.125 false 2.771,1.125 2.771,0.406 false 2.771,0.406 2.583,0.406 false 1.563,1.01 1.135,1.448 false 1.135,1.448 1.135,1.781 false 0.708,1.781 1.74,2.104 1.031,0.323 10 true Pump Side Port 1.594,0.333 2.542,0.604 0.948,0.271 10 true Tank Side Port

Install the evaporation tube.

HINT:

When installing the evaporation tube, first connect the pump side port, then connect the tank side port.


NOTICE:
·

Before installing the pipe, make sure that it is not damaged. Make sure that there is no foreign matter present on the connecting surfaces.


·

After connecting, check if the pipe and the connector are securely connected by pulling on them.




Hide 77285B 7.INSTALL NO. 1 FUEL TUBE CLAMP

a.
A394006

Install the 2 tube clamps to the fuel tank.


Hide 77209D 8.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Install the main tube to the fuel tube clamps.


Hide 77026A 9.INSTALL NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.

Install the tube to the fuel tube clamps.


b.

Connect the tube to the fuel suction with pump and gauge.