Home › Engine / Hybrid System › 2AZ-FE FUEL › FUEL SYSTEM
RM24M0E _51 Engine / Hybrid System _059542 2AZ-FE FUEL _0291801 FUEL SYSTEM L

2AZ-FE FUEL  FUEL SYSTEM  PRECAUTION  


BEFORE WORKING ON FUEL SYSTEM


a.

Do not work near an open flame.


b.

Keep gasoline away from rubber and leather parts.


c.

Discharge the fuel pressure before disconnecting the fuel line to prevent gasoline from spilling out. Refer to the following procedure.



DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

DISCHARGE FUEL SYSTEM PRESSURE procedures must be performed before disconnecting any part of the fuel system.


·

After performing the DISCHARGE FUEL SYSTEM PRESSURE procedures, pressure will remain in the fuel line. When disconnecting the fuel line, place a cloth or equivalent over fittings to reduce the risk of fuel spray.



a.

Fold back the floor carpet and remove the service hole cover.


b.

Disconnect the fuel pump connector.


c.

Start the engine. After the engine has stopped, turn the ignition switch off.

HINT:

DTC P0171 (system too lean) may be set.



d.

Check that the engine does not start.


e.

Remove the fuel tank cap, and let the air out of the fuel tank.


f.

Connect the fuel pump connector.


g.

Install the service hole cover and return the floor carpet to its original position.



DISCONNECT FUEL MAIN TUBE


A125337E10
2.24,2.198 2.24,2.74 false 1.021,4.25 1.031,3.896 false 1.021,4.25 1.854,4.146 false 0.969,1.271 0.708,0.969 false 0.708,0.969 0.708,0.677 false 1.948,0.479 2.677,0.646 0.729,0.167 10 false Retainer 0.031,0.021 1.042,0.375 1.01,0.354 10 false No. 2 Fuel Pipe Clamp 0.594,1.625 0.906,1.896 0.313,0.271 10 true Turn 1.979,1.854 3.073,2.188 1.094,0.333 10 true Fuel Hose Clamp 1.26,3.25 1.615,3.417 0.354,0.167 10 false Push 0.594,4.135 0.906,4.302 0.313,0.167 10 false SST

NOTICE:

Do not forcibly bend and twist the fuel main tube.


a.

Remove the fuel tube from the fuel hose clamp.


b.

Remove the fuel pipe clamp.


c.

Wipe off any dirt on the fuel tube connector.


d.

Hold the fuel tube connector, and then install SST.

SST
09268-21010  


e.

Turn SST to align the retainer inside the fuel tube connector with the chamfered part of SST.


f.

Insert SST into the fuel tube and hold it. Then push the fuel tube connector toward the SST side.


g.

Mount the retainer of the fuel tube connector onto the chamfered part of SST.


h.
A076220E64
2.188,0.76 2.26,0.406 false 2.26,1.573 2.26,1.875 false 0.594,1.375 0.594,1.708 false 1.375,0.875 1.104,0.438 1.104,0.438 1.573,0.875 false 2.917,1.323 2.917,1.531 false 2.26,0.406 2.438,0.406 false 0.542,0.313 1.021,0.51 0.479,0.198 10 false O-Ring 2.479,0.323 3.125,0.521 0.646,0.198 10 false Retainer 2.729,1.542 3.083,1.74 0.354,0.198 10 false Pipe 0.26,1.708 1.219,1.906 0.958,0.198 10 false Nylon Tube 1.948,1.865 2.573,2.063 0.625,0.198 10 false Housing

Slide SST and fuel tube connector together towards the fuel tube until they make a "click" sound, and then disconnect the fuel tube.


i.

Drain the fuel remaining inside the fuel tube.


j.

Cover the fuel tube and fuel pipe with a plastic bag to protect the disconnected part.



CONNECT FUEL MAIN TUBE


a.

Connect the fuel main tube.


b.

Push the fuel tube connector until it makes a "click" sound.


c.

Install the fuel pipe clamp.


d.

Install the fuel tube to the fuel hose clamp.



DISCONNECT FUEL TUBE CONNECTOR


A088336E81
1.052,0.198 1.531,0.438 0.479,0.24 10 false Pinch 1.448,1.906 1.927,2.104 0.479,0.198 10 false Pinch 0.615,1.958 0.927,2.156 0.313,0.198 10 false Pull

a.

Wipe off any dirt on the fuel tube connector.


b.

Pinch the fuel tube connector, and then disconnect the fuel tube. Do not use any tools.


c.

Drain the fuel remaining inside the fuel tube.


d.

Cover the fuel tube and fuel pipe with a plastic bag to protect the disconnected part.



CONNECT FUEL TUBE CONNECTOR


a.

Connect the fuel tube connector to the fuel pipe.


b.

Push the fuel tube connector until it makes a "click" sound.



HINT:

If it is difficult to connect the fuel tube connector, apply a small amount of new engine oil on the tip of the pipe.


CHECK FOR FUEL LEAKS


B135940E01
0.425,2.845 1.557,3.021 1.132,0.177 10 Intelligent Tester 0.6,2.589 0.6,2.832 false 1.48,2.058 1.864,2.214 0.385,0.156 10 DLC3 1.717,2.051 1.841,1.732 false

a.

Make sure that there are no fuel leaks after performing maintenance on the fuel system.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch on (IG), and push the intelligent tester main switch ON.

NOTICE:

Do not start the engine.



iii.

Select the Active Test mode on the intelligent tester.

HINT:

Refer to the intelligent tester operator's manual for further details.



iv.

Check that there are no leaks from the fuel system.


v.

Turn the ignition switch off.


vi.

Disconnect the intelligent tester from the DLC3.