Home › Engine / Hybrid System › 2GR-FE FUEL › FUEL SYSTEM
RM24M0E _51 Engine / Hybrid System _059543 2GR-FE FUEL _0291802 FUEL SYSTEM G

2GR-FE FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK FOR FUEL PUMP OPERATION AND FUEL LEAKS

a.

Check fuel pump operation.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the engine switch on (IG) and push the intelligent tester main switch on.

NOTICE:

Do not start the engine.



iii.

Enter the following menus: Power train / Engine / Active Test / Control the Fuel Pump / Speed.


iv.

Check for pressure in the fuel inlet tube from the fuel line. Check that the sound of fuel flowing from the fuel tank can be heard. If no sound can be heard, check the integration relay, fuel pump, ECM and wiring connector.



b.

Check for fuel leaks (*1).

i.

Check that there are no fuel leaks anywhere on the system after performing maintenance. If there is a fuel leak, repair or replace parts as necessary.



c.

Turn the engine switch off.


d.

Disconnect the intelligent tester from the DLC3.


Hide 2.CHECK FUEL PRESSURE

a.

Discharge the fuel system pressure (See page Engine / Hybrid System>2GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


b.

Using a voltmeter, measure the battery voltage.

Standard voltage:

11 to 14 V



c.

Disconnect the cable from the negative (-) battery terminal.


d.

Disconnect the fuel hose from the fuel main tube (See page Engine / Hybrid System>2GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


e.
A255967E12
0.844,0.49 0.604,0.49 false 1.51,0.781 1.51,1.073 false 1.104,0.99 1.104,1.177 false 2.844,0.417 2.573,0.177 2.573,0.177 2.448,0.177 false 1.615,3.344 1.875,3.083 1.875,3.083 1.958,3.083 false 1.302,3.979 1.438,4.115 1.438,4.115 1.531,4.115 false 2.75,3.302 2.75,3.604 false 2.365,3.563 2.365,3.792 false 0.594,1.146 0.438,0.969 0.438,0.969 0.354,0.969 false 1.177,0.323 1.375,0.323 false 0.396,0.396 0.552,0.552 0.156,0.156 10 false *a 1.438,1.104 1.646,1.292 0.208,0.188 10 false *a 1.031,1.198 1.24,1.406 0.208,0.208 10 false *b 2.25,0.104 2.406,0.26 0.156,0.156 10 false *c 1.406,0.24 1.563,0.396 0.156,0.156 10 false *d 0.135,0.885 0.292,1.042 0.156,0.156 10 false *1 2.292,3.813 2.5,4.01 0.208,0.198 10 false *f 1.969,2.99 2.125,3.146 0.156,0.156 10 false *a 1.552,4.021 1.854,4.229 0.302,0.208 10 false *e 2.688,3.635 2.906,3.854 0.219,0.219 10 false *g

Install SST (pressure gauge) using SST and a fuel tube connector as shown in the illustration.

Text in Illustration
*1 Fuel Tube Sub-assembly (Vehicle Side)
*a SST (Hose Band)
*b SST (T-joint)
*c SST (Gauge)
*d SST (Hose Joint)
*e SST (Hose)
*f SST (Fuel Tube Connector)
*g Fuel Pipe (Vehicle Side)

SST
09268-31014  (09268-41500, 09268-41700, 95336-08070)
09268-45014  (09268-41200, 09268-41220, 09268-41250)


f.

Clear up any spilled gasoline.


g.

Connect the cable to the negative (-) battery terminal.


h.

Connect the intelligent tester to the DLC3.


i.

Enter the following menus: Power train / Engine / Active Test / Control the Fuel Pump / Speed.


j.

Measure the fuel pressure.

Fuel pressure:

304 to 343 kPa (3.1 to 3.5 kgf*cm2, 44.1 to 49.7 psi)


·

If the fuel pressure is greater than the standard value, replace the fuel pressure regulator.

·

If the fuel pressure is less than the standard value, check the fuel hoses and connections, fuel pump, fuel filter and fuel pressure regulator.



k.

Disconnect the intelligent tester from the DLC3.


l.

Start the engine.


m.

Measure the fuel pressure at idle.

Fuel pressure:

304 to 343 kPa (3.1 to 3.5 kgf*cm2, 44.1 to 49.7 psi)



n.

Stop the engine.


o.

Check that the fuel pressure remains as specified for 5 minutes after the engine stops.

Fuel pressure:

147 kPa (1.5 kgf*cm2, 21 psi) or more


If the fuel pressure is not as specified, check the fuel pump, pressure regulator and/or fuel injectors.


p.

After checking the fuel pressure, disconnect the cable from the negative (-) battery terminal and carefully remove the SST to prevent gasoline from splashing.


q.

Reconnect the fuel tube to the main fuel tube (fuel tube connector).


r.

Install the No. 1 fuel pipe clamp to the fuel tube connector.


s.

Check for fuel leaks (*1).