Home › Engine / Hybrid System › 2AZ-FE ENGINE MECHANICAL › TIMING CHAIN
RM24M0E _51 Engine / Hybrid System _059548 2AZ-FE ENGINE MECHANICAL _0291833 TIMING CHAIN G

2AZ-FE ENGINE MECHANICAL  TIMING CHAIN  INSPECTION  


PROCEDURE

Hide 13540 1.INSPECT NO. 1 CHAIN TENSIONER

a.
A098357E13
0.51,0.573 0.583,0.573 0.583,0.573 0.729,0.771 false 0.469,0.958 0.469,1.823 false 0.948,1.5 1.302,1.677 0.354,0.177 10 false Lock 0.24,1.823 0.625,1.99 0.385,0.167 10 false Move 0.021,0.469 0.417,0.625 0.396,0.156 10 false Raise

Check that the plunger moves smoothly when the ratchet pawl is raised with your finger.


b.

Release the ratchet pawl, then check that the plunger is locked in place by the ratchet pawl and does not move when pushed with your finger.


Hide 13506 2.INSPECT CHAIN SUB-ASSEMBLY

a.
A132684E04
1.697,0.93 2.944,1.099 1.246,0.170 10 Measurement Area 0.453,1.038 1.139,1.202 0.685,0.165 10 114.5 mm 2.932,0.06 3.331,0.223 0.400,0.162 10 140 N 1.63,1.026 1.562,1.026 1.562,1.026 1.367,1.426 false

Using a spring scale and vernier caliper, measure a 15 link section of the chain when it is stretched with a force of 140 N (14.3 kgf, 32 lbf).

Maximum chain elongation:

114.5 mm (4.507 in.)


If the chain elongation is greater than the maximum, replace the chain sub-assembly.

HINT:

Take the measurement at 3 or more places and average the measurements to determine the length.



Hide 13506 3.INSPECT NO. 2 CHAIN SUB-ASSEMBLY

a.
A132684E02
1.687,0.93 2.933,1.099 1.246,0.170 10 Measurement Area 0.453,1.038 1.139,1.202 0.685,0.165 10 102.2 mm 2.921,0.08 3.321,0.242 0.400,0.162 10 140 N 1.63,1.016 1.528,1.016 1.528,1.016 1.346,1.426 false

Using a spring scale and vernier caliper, measure a 15 link section of the chain when it is stretched with a force of 140 N (14.3 kgf, 32 lbf).

Maximum chain elongation:

102.2 mm (4.024 in.)


If the chain elongation is greater than the maximum, replace the No. 2 chain sub-assembly.

HINT:

Take the measurement at 3 or more places and average the measurements to determine the length.



Hide 13559 4.INSPECT CHAIN TENSIONER SLIPPER

a.
A033838

Using a vernier caliper, measure the tensioner slipper wear.

Maximum wear:

1.0 mm (0.039 in.)


If the wear is greater than the maximum, replace the chain tensioner slipper.


Hide 13561 5.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A036686

Using a vernier caliper, measure the vibration damper wear.

Maximum wear:

1.0 mm (0.039 in.)


If the wear is greater than the maximum, replace the No. 1 chain vibration damper.


Hide 13521 6.INSPECT CRANKSHAFT TIMING SPROCKET

a.
A053035

Wrap the chain around the timing sprocket.


b.

Using a vernier caliper, measure the timing gear diameter with the chain.

Minimum gear diameter (with chain):

51.6 mm (2.031 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


If the gear diameter is less than the minimum, replace the chain sub-assembly and crankshaft timing sprocket.


Hide 15163 7.INSPECT OIL PUMP DRIVE SPROCKET

a.
A053035

Wrap the chain around the drive sprocket.


b.

Using a vernier caliper, measure the drive gear diameter with the chain.

Minimum gear diameter (with chain):

48.2 mm (1.898 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


If the gear diameter is less than the minimum, replace the No. 2 chain sub-assembly and oil pump drive sprocket.


Hide 15163 8.INSPECT OIL PUMP DRIVE SHAFT SPROCKET

a.
A053036

Wrap the chain around the drive shaft sprocket.


b.

Using a vernier caliper, measure the drive shaft gear diameter with the chain.

Minimum gear diameter (with chain):

48.2 mm (1.898 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


If the gear diameter is less than the minimum, replace the No. 2 chain sub-assembly and oil pump drive shaft sprocket.