Home › Engine / Hybrid System › 2AZ-FE ENGINE MECHANICAL › CYLINDER HEAD
RM24M0E _51 Engine / Hybrid System _059548 2AZ-FE ENGINE MECHANICAL _0291834 CYLINDER HEAD A

2AZ-FE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.
A124781

Heat the cylinder head to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head on wooden blocks.


c.
A098136E02
2.031,0.635 2.552,0.792 2.552,0.792 2.104,1.031 false 2.604,0.698 2.927,0.875 0.323,0.177 10 false SST

Using SST and a hammer, tap out the guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A124781

Heat the cylinder head to 80 to 100°C (176 to 212°F).


e.

Place the cylinder head on wooden blocks.


f.
A124782

Using a caliper gauge, measure the bush bore diameter of the cylinder head.

Standard diameter:

10.285 to 10.306 mm (0.4049 to 0.4058 in.)


If the bush bore diameter of the cylinder head is greater than 10.306 mm (0.4058 in.), machine the bush bore to the dimension of 10.335 to 10.365 mm (0.4068 to 0.4077 in.).

Standard valve guide bush diameter:
Condition Specified Condition
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S
(0.05 mm)
10.383 to 10.394 mm (0.4088 to 0.4092 in.)


If the bush bore diameter of the cylinder head is greater than 10.394 mm (0.4092 in.), replace the cylinder head.


g.
A098138E02
2.073,0.604 2.573,0.771 2.573,0.771 2.156,1.021 false 2.625,0.677 2.938,0.844 0.313,0.167 10 false SST

Using SST and a hammer, tap in a new guide bush to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard protrusion height:

9.6 to 10.0 mm (0.378 to 0.394 in.)



h.
A124783

Using a sharp 5.5 mm reamer, ream the valve guide bush to the standard specified clearance between the valve guide bush and valve stem.

Standard oil clearance:

0.025 to 0.060 mm (0.0010 to 0.0024 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.
A124781

Heat the cylinder head to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head on wooden blocks.


c.
A098137E02
1.219,0.688 0.615,0.281 0.615,0.281 1.073,1.198 false 0.25,0.188 0.563,0.365 0.313,0.177 10 false SST

Using SST and a hammer, tap out the guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A087006

Heat the cylinder head to 80 to 100°C (176 to 212°F).


e.

Place the cylinder head on wooden blocks.


f.
A124782

Using a caliper gauge, measure the bush bore diameter of the cylinder head.

Standard diameter:

10.285 to 10.306 mm (0.4049 to 0.4058 in.)


If the bush bore diameter of the cylinder head is greater than 10.306 mm (0.4058 in.), machine the bush bore to the dimension of 10.335 to 10.365 mm (0.4068 to 0.4077 in.).

Standard valve guide bush diameter:
Condition Specified Condition
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S
(0.05 mm)
10.383 to 10.394 mm (0.4088 to 0.4092 in.)


If the bush bore diameter of the cylinder head is greater than 10.394 mm (0.4092 in.), replace the cylinder head.


g.
A098139E02
1.24,0.677 0.615,0.292 0.615,0.292 1.115,1.188 false 0.229,0.208 0.552,0.396 0.323,0.188 10 false SST

Using SST and a hammer, tap in a new guide bush to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard protrusion height:

9.6 to 10.0 mm (0.378 to 0.394 in.)



h.
A124783

Using a sharp 5.5 mm reamer, ream the valve guide bush to the standard specified clearance between the valve guide bush and valve stem.

Standard oil clearance:

0.030 to 0.065 mm (0.0012 to 0.0026 in.)



Hide 3.REPLACE STUD BOLT

NOTICE:

If the stud bolt is deformed or threads are damaged, replace it.


a.

Using E5 and E7 "torx" socket wrenches, remove the 11 stud bolts.


b.

Using E5 and E7 "torx" socket wrenches, install 11 new stud bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

for bolt A and B

9.5 N*m (97 kgf*cm, 84 in.*lbf)

for bolt C and D


A393969E01
1.375,0.646 1.688,0.917 0.313,0.271 10 false A 4.313,2.125 4.625,2.396 0.313,0.271 10 false B 1.427,2.823 1.74,3.094 0.313,0.271 10 false C 4.51,2.823 4.823,3.094 0.313,0.271 10 false D 0.906,6.24 1.427,6.542 0.521,0.302 10 false A (M6) 2.219,6.24 2.74,6.542 0.521,0.302 10 false B (M6) 3.594,6.26 4.115,6.563 0.521,0.302 10 false C (M8) 5.375,6.25 5.896,6.552 0.521,0.302 10 false D (M8) 1.698,0.49 2.813,0.792 1.115,0.302 10 false Front Side 4.667,0.51 5.781,0.813 1.115,0.302 10 false Upper Side 4.635,2.563 5.75,2.865 1.115,0.302 10 false Exhaust Side 1.708,2.573 2.823,2.875 1.115,0.302 10 false Intake Side 1.188,4.708 2.031,4.958 0.844,0.25 10 false 33.3 (1.311) 1.365,5.417 2.135,5.604 0.771,0.188 10 true 12.0 (0.472) 1.396,5.927 2.135,6.115 0.74,0.188 10 true 9.0 (0.354) 2.521,4.292 3.448,4.552 0.927,0.26 10 false 46.5 (1.831) 4.26,4.219 5.125,4.479 0.865,0.26 10 false 49.5 (1.949) 5.938,4.583 6.74,4.802 0.802,0.219 10 false 37.5 (1.476) 4.24,4.979 5.042,5.167 0.802,0.188 10 true 24.0 (0.949) 4.219,5.875 5.021,6.063 0.802,0.188 10 true 13.0 (0.512) 5.917,5.333 6.719,5.521 0.802,0.188 10 true 18.0 (0.701) 6.417,6.375 7.021,6.656 0.604,0.281 10 false mm (in.) 2.708,4.958 3.479,5.146 0.771,0.188 10 true 12.0 (0.472) 2.708,5.896 3.479,6.083 0.771,0.188 10 true 12.0 (0.472) 5.927,5.885 6.729,6.073 0.802,0.188 10 true 13.0 (0.512) 2.604,0.656 2.917,0.927 0.313,0.271 10 false A 6.385,1.729 6.698,2 0.313,0.271 10 false B 2.594,2.844 2.906,3.115 0.313,0.271 10 false C 5.427,2.833 5.74,3.104 0.313,0.271 10 false D 4.167,3.948 4.479,4.219 0.313,0.271 10 false D 4.99,3.938 5.302,4.208 0.313,0.271 10 false D 5.823,3.927 6.135,4.198 0.313,0.271 10 false D


Hide 4.REPLACE RING PIN

NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.


a.

Remove the 4 ring pins.


b.
A098140E07
0.219,0.115 1,0.292 0.781,0.177 10 false Upper Side 2.167,3.094 2.813,3.292 0.646,0.198 10 false mm (in.) 0.365,1.927 0.958,2.115 0.594,0.188 10 false 11 (0.43) 2.385,2.042 2.958,2.208 0.573,0.167 10 false 3 (0.12) 0.813,2.823 1.333,3.01 0.521,0.188 10 false 8 (0.32)

Using a plastic-faced hammer, tap in 4 new ring pins to the specified protrusion height.

Protrusion height:

3.0 mm (0.12 in.)