Home › Engine / Hybrid System › 2GR-FE COOLING › COOLING FAN SYSTEM
RM24M0E _51 Engine / Hybrid System _059551 2GR-FE COOLING _0291840 COOLING FAN SYSTEM G

2GR-FE COOLING  COOLING FAN SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT COOLING FAN SYSTEM

a.

Put the vehicle in the following conditions:

i.

The ignition switch is off.


ii.

The coolant temperature is less than 95°C (203°F).


iii.

The battery voltage is between 9 and 14 V.


iv.

The A/C switch is OFF.



b.

Clamp the 400 A probe of an ammeter over the M+ wire of each cooling fan motor.


c.

Turn the ignition switch to the ON position and wait for approximately 10 seconds. Check that the fan stops.


d.

Start the engine. Check that the fan stops with the engine idling.

HINT:
·

Make sure that the radiator engine coolant temperature is less than 95°C (203°F).

·

Turn the A/C switch OFF.




e.

Check that the fan operates when the A/C switch is turned on (MAX COOL and the magnetic clutch is operating).

Standard current:

with Trailer Towing System

Item Specified Condition
No. 1 cooling fan motor 4 to 24 A
No. 2 cooling fan motor 4 to 24 A


Standard current:

without Trailer Towing System

Item Specified Condition
No. 1 cooling fan motor 4 to 20 A
No. 2 cooling fan motor 4 to 20 A


HINT:

The coolant temperature is less than 95°C (203°F).



f.

Check that the fan operates when the engine coolant temperature sensor connector is disconnected.

Standard current:

with Trailer Towing System

Item Specified Condition
No. 1 cooling fan motor 4 to 24 A
No. 2 cooling fan motor 4 to 24 A


Standard current:

without Trailer Towing System

Item Specified Condition
No. 1 cooling fan motor 4 to 20 A
No. 2 cooling fan motor 4 to 20 A



g.
A139339E05
1.276,0.231 2.508,0.413 1.232,0.181 10 Operating Diagram 1.694,0.724 2.285,0.880 0.590,0.156 10 A/C OFF 0.241,1.18 0.741,1.324 0.500,0.144 10 MAX HI 0.602,2.435 0.810,2.590 0.209,0.155 10 LO 0.033,1.686 0.467,2.017 0.434,0.331 10 Fan Speed 1.373,3.468 1.571,3.625 0.197,0.157 10 95 1.715,3.468 1.912,3.625 0.197,0.157 10 97 2.386,3.468 2.658,3.625 0.272,0.157 10 100 2.763,3.468 3.017,3.625 0.254,0.157 10 102 1.29,3.817 1.562,3.974 0.272,0.157 10 203 1.688,3.817 1.960,3.974 0.272,0.157 10 207 2.4,3.817 2.672,3.974 0.272,0.157 10 212 2.776,3.817 3.048,3.974 0.272,0.157 10 216 3.08,3.823 3.349,3.980 0.269,0.157 10 (°F) 3.073,3.476 3.351,3.667 0.277,0.192 10 (°C)

After the engine is warmed up, check that the fan operates as shown in the illustration.

HINT:
·

The coolant temperature at which the fan starts operating is approximately 95°C (203°F).


·

This system can also be checked using the intelligent tester.


·

Select the following menu items: Powertrain / Engine / Data List / Initial Engine Coolant Temp.