Home › Engine / Hybrid System › 2GR-FE COOLING › RADIATOR
RM24M0E _51 Engine / Hybrid System _059551 2GR-FE COOLING _0291847 RADIATOR A

2GR-FE COOLING  RADIATOR  REASSEMBLY  


PROCEDURE

Hide 16441 1.INSTALL UPPER RADIATOR TANK

a.
U188275E02
2.292,1.25 2.573,0.833 2.573,0.833 2.667,0.833 false 2.719,0.75 3.229,0.927 0.51,0.177 10 false O-Ring 1.458,2.927 2.135,3.083 0.677,0.156 10 false X Twisted 2.479,2.917 3.156,3.073 0.677,0.156 10 false X Twisted 0.604,2.896 1.094,3.073 0.49,0.177 10 false Normal

After checking that there are no foreign objects in the lock plate groove, install a new O-ring without twisting it.

HINT:

When cleaning the lock plate groove, lightly rub it with sandpaper without scratching it.



b.
A132666E01
0.409,0.1 1.175,0.276 0.766,0.176 10 CORRECT 1.975,0.1 2.861,0.276 0.887,0.176 10 INCORRECT 1.539,1.094 1.907,1.265 0.367,0.171 10 Tank 0.212,1.208 0.893,1.379 0.681,0.171 10 Lock Plate 2.408,0.712 1.973,1.173 false 0.587,0.919 0.587,1.179 false

A162794E01
2.224,0.269 2.995,0.439 0.771,0.170 10 CORRECT 2.293,1.284 2.994,1.433 0.701,0.149 10 Lock Plate 2.401,0.994 2.407,1.278 false 2.214,1.729 3.065,1.909 0.851,0.180 10 INCORRECT 2.276,2.741 2.603,2.883 0.327,0.142 10 Tank 2.564,2.249 2.469,2.728 false

Tap the lock plate with a plastic-faced hammer so that there is no gap between the lock plate and the tank.

NOTICE:

Do not tap the areas protruding around the pipes, brackets or tank ribs.



c.
A104624E06
1.615,2.906 1.615,2.573 false 0.625,3.01 0.625,3.552 false 2.542,3.292 2.542,3.813 false 2.344,1.844 1.667,0.677 1.667,0.677 1.51,0.677 false 2.844,2.063 2.438,0.219 2.438,0.219 2.323,0.219 false 0.323,1.052 1.323,1.25 1,0.198 10 false Dimension B 0.99,0.583 1.458,0.781 0.469,0.198 10 false Part A 1.417,0.125 2.26,0.323 0.844,0.198 10 false Stopper Bolt 1.49,2.375 1.854,2.573 0.365,0.198 10 false SST 0.125,3.583 1.427,3.792 1.302,0.208 10 false Punch Assembly 1.875,3.833 3.188,4.042 1.313,0.208 10 false Overhaul Handle

Install the punch assembly to the overhaul handle, inserting it in the hole in part A as shown in the illustration.

SST
09230-01010  (09231-01010, 09231-01020)
09231-14010  


d.

While gripping the handle, adjust the stopper bolt so that dimension B is as specified below.

Dimension B:

8.65 mm (0.341 in.)



e.

Lightly press SST against the lock plate in the order shown in the illustration. After repeating this procedure a few times, fully crimp the lock plate by squeezing the handle until stopped by the stopper bolt.

A394012E01
4.5,0.521 4.646,0.521 4.646,0.521 4.938,0.74 false 5.094,0.844 5.469,0.448 5.469,0.448 5.656,0.448 false 5.75,2.583 5.625,2.271 5.625,2.271 5.458,2.271 false 5.615,2.833 5.479,2.563 5.479,2.563 5.333,2.563 false 5.448,3.323 5.552,3.323 5.552,3.323 5.594,3.021 false 1.24,1.26 1.698,1.531 0.458,0.271 10 false 5 1.823,1.26 2.281,1.531 0.458,0.271 10 false 3 2.458,1.271 2.917,1.542 0.458,0.271 10 false 7 3.094,1.698 3.552,1.969 0.458,0.271 10 false 2 0.594,1.708 1.052,1.979 0.458,0.271 10 false 1 1.219,2.219 1.677,2.49 0.458,0.271 10 false 6 1.844,2.24 2.302,2.51 0.458,0.271 10 false 4 2.458,2.219 2.917,2.49 0.458,0.271 10 false 8 5.729,0.365 6.188,0.635 0.458,0.271 10 false SST 3.677,0.438 4.5,0.719 0.823,0.281 10 false Stopper Bolt 4.958,2.479 5.417,2.75 0.458,0.271 10 false Tank 4.75,3.219 5.51,3.521 0.76,0.302 10 false Lock Plate 5.115,2.188 5.573,2.458 0.458,0.271 10 false SST

SST
09230-01010  (09231-01010, 09231-01020)
09231-14010  

NOTICE:
·
U188350E02
0.531,0.188 0.688,0.354 0.156,0.167 10 false A 2.219,0.198 2.375,0.365 0.156,0.167 10 false A 2.229,3.5 2.385,3.667 0.156,0.167 10 false A 1.313,2.802 1.469,2.969 0.156,0.167 10 false A 0.563,3.635 0.719,3.802 0.156,0.167 10 false A 1.375,0.99 1.531,1.156 0.156,0.167 10 false B 2.75,1.167 2.906,1.333 0.156,0.167 10 false B 2.74,2.396 2.896,2.563 0.156,0.167 10 false B

Do not crimp the protruding areas around ports A and brackets B.

·
A132669

Do not use SST to crimp the circled areas indicated in the illustration. Use pliers and be careful not to damage the core plates.




f.
A162808E01
3.02,0.607 3.149,0.769 0.129,0.162 10 A

Check the lock plate height A after completing the crimping.

Standard plate height A:

10.05 mm (0.3957 in.)


If the height is not as specified, readjust the stopper bolt of the handle and crimp the lock plate again.


Hide 16461 2.INSTALL LOWER RADIATOR TANK

HINT:

The installation procedure for the lower radiator tank is the same as that for the upper radiator tank.


Hide 16400B 3.INSTALL RADIATOR DRAIN COCK PLUG

a.

Install a new O-ring to the drain plug.


b.

Install the drain plug.


Hide 4.INSPECT FOR WATER LEAK

a.
A132671E01
2.421,0.397 2.743,0.566 0.323,0.170 10 SST 1.94,0.74 2.262,0.910 0.323,0.170 10 SST 2.792,0.486 3.008,0.486 false 1.894,0.832 1.679,1.088 false

Plug the inlet and outlet pipes of the radiator with SST.

SST
09230-01010  (09231-00030, 09231-00060)


b.

Using a radiator cap tester, apply pressure to the radiator.

Standard test pressure:

177 kPa (1.8 kgf/cm2, 26 psi)



c.

Submerge the radiator in water.


d.
A090282E05
2.323,1.021 2.5,0.75 2.5,0.75 2.552,0.75 false 1.115,0.333 1.469,0.333 false 1.708,1.813 1.823,1.813 1.823,1.813 2.198,1.604 false 2.583,0.656 3.271,0.813 0.688,0.156 10 false Lock Plate 0.708,0.25 1.042,0.406 0.333,0.156 10 false Tank 1.104,1.708 1.604,1.896 0.5,0.188 10 false O-Ring

Inspect for leak.

HINT:

On radiators with resin tanks, there is clearance between the tank and lock plate where a minute amount of air will remain, giving the appearance of an air leak when the radiator is submerged in water. Therefore, before doing the water leak test, first swish the radiator around in the water until all air bubbles disappear.