Home › Engine / Hybrid System › 2AZ-FE COOLING › COOLANT
RM24M0E _51 Engine / Hybrid System _059552 2AZ-FE COOLING _0291850 COOLANT A

2AZ-FE COOLING  COOLANT  REPLACEMENT  


PROCEDURE

Hide 51441 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 2.DRAIN ENGINE COOLANT

a.
A114387

Remove the hood to cowl top seal.


b.
A114388

Remove the cowl top ventilator louver cover.


c.

Loosen the radiator drain cock plug, then drain the engine coolant.

A304353E04
3.427,0.365 3.24,0.365 3.24,0.365 3.01,0.896 false 2.24,0.344 2.427,0.344 2.427,0.344 2.583,0.854 false 3.375,4 3.469,4.313 3.469,4.313 3.583,4.313 false 3.479,0.271 3.781,0.51 0.302,0.24 10 false *1 2.052,0.26 2.354,0.5 0.302,0.24 10 false *2 3.615,4.229 3.917,4.469 0.302,0.24 10 false *3

Text in Illustration
*1 Radiator Reservoir *2 Radiator Reservoir Cap
*3 Radiator Drain Cock Plug - -

HINT:

Collect the engine coolant in a container and dispose of it according to the regulations in your area.



d.

Remove the radiator reservoir cap.

CAUTION:

Do not remove the radiator reservoir cap while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



Hide 3.ADD ENGINE COOLANT

a.

Tighten the radiator drain cock plug by hand.


b.

Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening.


c.
U185595E02
1.458,0.51 2.823,0.51 true 2.875,0.417 3.146,0.635 0.271,0.219 10 false *a

Continue adding TOYOTA SLLC until it is filled to the B line at the base of the reservoir's filler neck.

Text in Illustration
*a B Line

Standard Capacity (for Automatic Transaxle):
Item Specified Condition
Engine Coolant 6.2 liters (6.6 US qts, 5.5 Imp. qts)


Standard Capacity (for CVT):
Item Condition Specified Condition
Engine Coolant w/ Trailer Towing System w/ Rear Heater 8.8 liters (9.3 US qts, 7.7 Imp. qts)
w/o Rear Heater 6.9 liters (7.3 US qts, 6.1 Imp. qts)
w/o Trailer Towing System w/ Rear Heater 8.4 liters (8.9 US qts, 7.4 Imp. qts)
w/o Rear Heater 6.5 liters (6.9 US qts, 5.7 Imp. qts)


NOTICE:

Never use water as a substitute for engine coolant.


HINT:

TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).



d.

Press the No. 1 radiator hose and No. 2 radiator hose several times by hand, and then check the level of the engine coolant. If the engine coolant level drops below the B line, add TOYOTA SLLC to the B line.


e.

Install the radiator reservoir cap.


f.

Start the engine and warm it up until the fan operates.

i.

Set the air conditioning as follows while warming up the engine.

Item Specified Condition
Manual Air Conditioning System Fan speed: Any setting except OFF
Temperature: Toward WARM
Air conditioning switch: OFF
Automatic Air Conditioning System Temperature: Toward MAX
Air conditioning switch: OFF


ii.

Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the fan operates.

NOTICE:
·

Make sure that the radiator reservoir still has some engine coolant in it.

·

Pay attention to the needle of the engine coolant temperature gauge. Make sure that the needle does not show an abnormally high temperature.

·

If there is not enough engine coolant, the engine may overheat or be seriously damaged.

·

Immediately after starting the engine, if the radiator reservoir does not have enough engine coolant, perform the following: 1) stop the engine, 2) wait until the engine coolant has cooled down, and 3) add engine coolant until the engine coolant is filled to the B line.

·

Run the engine at 2,000 rpm until the engine coolant level has stabilized.





g.

Stop the engine and wait until the engine coolant cools down to ambient temperature.


h.
U188280E02
1.26,1.156 3.281,1.156 false 1.26,1.417 3.281,1.417 false 3.115,1.802 3.115,0.771 false

Check that the engine coolant level is between the FULL and LOW line.

If the engine coolant level is below the LOW line, repeat all of the procedures above.

If the engine coolant level is above the FULL line, drain engine coolant so that the engine coolant level is between the FULL and LOW line.


i.

Install the cowl top ventilator louver cover.


j.

Install the hood to cowl top seal.


Hide 51441 5.INSTALL NO. 1 ENGINE UNDER COVER