Home › Engine / Hybrid System › 2AZ-FE COOLING › RADIATOR
RM24M0E _51 Engine / Hybrid System _059552 2AZ-FE COOLING _0291853 RADIATOR A

2AZ-FE COOLING  RADIATOR  REASSEMBLY  


PROCEDURE

Hide 16441 1.INSTALL RADIATOR TANK INLET AND TANK OUTLET

a.
U188275E02
2.292,1.25 2.573,0.833 2.573,0.833 2.667,0.833 false 2.719,0.75 3.229,0.927 0.51,0.177 10 false O-Ring 1.458,2.927 2.135,3.083 0.677,0.156 10 false X Twisted 2.479,2.917 3.156,3.073 0.677,0.156 10 false X Twisted 0.604,2.896 1.094,3.073 0.49,0.177 10 false Normal

Check that there are no foreign objects in the lock plate groove, and install a new O-ring. Make sure the O-ring is not twisted.


b.
A132666E01
0.409,0.1 1.175,0.276 0.766,0.176 10 CORRECT 1.975,0.1 2.861,0.276 0.887,0.176 10 INCORRECT 1.539,1.094 1.907,1.265 0.367,0.171 10 Tank 0.212,1.208 0.893,1.379 0.681,0.171 10 Lock Plate 2.408,0.712 1.973,1.173 false 0.587,0.919 0.587,1.179 false

Tap the lock plate with a plastic-faced hammer so that there is no gap between the lock plate and the tank.


Hide 2.ASSEMBLE SST

a.
A120276E02
0.322,1.323 1.154,1.482 0.832,0.158 10 Dimension B 2.6,0.204 3.033,0.374 0.434,0.170 10 Part A 2.112,1.558 2.955,1.738 0.843,0.180 10 Stopper Bolt 1.971,2.846 3.053,3.017 1.082,0.171 10 Overhaul Handle 1.474,3.04 1.804,3.205 0.330,0.165 10 SST 0.039,2.846 1.105,3.033 1.066,0.187 10 Punch Assembly 2.331,0.698 2.535,0.302 false 2.846,1.022 2.569,1.565 false 0.654,2.469 0.654,2.805 false 1.649,3.024 1.649,2.905 1.649,2.905 1.854,2.743 false

Install the punch assembly to part A of the overhaul handle as shown in the illustration.

SST
09230-01010  
09231-14010  


b.

While gripping the handle, adjust the stopper bolt so that dimension B is as specified below.

Dimension B:

8.4 mm (0.331 in.)



Hide 3.CAULK LOCK PLATE

a.

Lightly press SST against the lock plate in the order shown in the illustration. After repeating this a few times, fully caulk the lock plate by squeezing the handle until stopped by the stopper bolt.

A393992E01
5.302,2.469 5.646,2.698 false 4.875,1.448 6.083,1.448 true 4.302,0.99 4.677,1.135 true 5.229,2.719 5.521,2.917 false 5.344,3.323 5.479,3.104 false 1.219,1.24 1.531,1.438 0.313,0.198 10 false 5 1.802,1.24 2.115,1.438 0.313,0.198 10 false 3 2.458,1.24 2.771,1.438 0.313,0.198 10 false 7 3.073,1.646 3.385,1.844 0.313,0.198 10 false 2 2.458,2.135 2.771,2.333 0.313,0.198 10 false 8 1.854,2.135 2.167,2.333 0.313,0.198 10 false 4 1.208,2.146 1.521,2.344 0.313,0.198 10 false 6 0.531,1.646 0.844,1.844 0.313,0.198 10 false 1 3.448,0.885 4.385,1.156 0.938,0.271 10 false Stopper Bolt 6.167,1.365 6.75,1.604 0.583,0.24 10 false SST 4.844,2.615 5.427,2.854 0.583,0.24 10 false Tank 4.635,3.25 5.344,3.51 0.708,0.26 10 false Lock Plate 4.969,2.365 5.552,2.604 0.583,0.24 10 false SST

SST
09230-01010  

NOTICE:
·
U188350E02
0.531,0.188 0.688,0.354 0.156,0.167 10 false A 2.219,0.198 2.375,0.365 0.156,0.167 10 false A 2.229,3.5 2.385,3.667 0.156,0.167 10 false A 1.313,2.802 1.469,2.969 0.156,0.167 10 false A 0.563,3.635 0.719,3.802 0.156,0.167 10 false A 1.375,0.99 1.531,1.156 0.156,0.167 10 false B 2.75,1.167 2.906,1.333 0.156,0.167 10 false B 2.74,2.396 2.896,2.563 0.156,0.167 10 false B

Do not press the protruding areas around ports A and Brackets B.

·
A132669

Do not use SST to press the areas indicated by the circle marks in the illustration. Use pliers and be careful not to damage the core plates.




b.
A132670E01
3.061,0.675 3.181,0.852 0.120,0.177 10 A

Check the lock plate height A after completing the caulking.

Standard plate height A:

8.65 mm (0.341 in.)


If the height is not as specified, readjust the stopper bolt of the handle and caulk the lock plate again.


Hide 16400B 4.INSTALL RADIATOR DRAIN COCK PLUG

a.

Install a new O-ring to the drain plug.


b.

Install the drain plug.


Hide 5.INSPECT FOR WATER LEAKS

a.
A132671E01
2.421,0.397 2.743,0.566 0.323,0.170 10 SST 1.94,0.74 2.262,0.910 0.323,0.170 10 SST 2.792,0.486 3.008,0.486 false 1.894,0.832 1.679,1.088 false

Plug the inlet and outlet pipes of the radiator with SST.


b.

Using a radiator cap tester, apply pressure to the radiator.

Standard test pressure:

177 kPa (1.8 kgf/cm2, 26 psi)



c.

Submerge the radiator in water.


d.
A090282E05
2.323,1.021 2.5,0.75 2.5,0.75 2.552,0.75 false 1.115,0.333 1.469,0.333 false 1.708,1.813 1.823,1.813 1.823,1.813 2.198,1.604 false 2.583,0.656 3.271,0.813 0.688,0.156 10 false Lock Plate 0.708,0.25 1.042,0.406 0.333,0.156 10 false Tank 1.104,1.708 1.604,1.896 0.5,0.188 10 false O-Ring

Inspect for leaks.

HINT:

On radiators with resin tanks, there is clearance between the tank and lock pate where a small amount of air will remain. This air is released when the radiator is submerged in water, giving the appearance of an air leak. Before performing the water leak test, first shake the radiator in the water until all air bubbles are released.