Home › Engine / Hybrid System › 2GR-FE LUBRICATION › OIL AND OIL FILTER
RM24M0E _51 Engine / Hybrid System _059553 2GR-FE LUBRICATION _0291857 OIL AND OIL FILTER A

2GR-FE LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.

·

In order to preserve the environment, used oil and used oil filters must be disposed of at designated disposal sites.



PROCEDURE

Hide 51442 1.REMOVE NO. 2 ENGINE UNDER COVER

Hide 2.DRAIN ENGINE OIL

a.

Remove the oil filler cap.


b.

Remove the oil pan drain plug and gasket, and drain the oil into a container.


c.

Clean the oil pan drain plug.


d.

Install the oil pan drain plug with a new gasket.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 04152 3.REMOVE OIL FILTER ELEMENT

a.
A204919E01
1.653,0.315 1.868,0.519 0.215,0.203 10 *1 1.606,0.401 1.426,0.401 1.426,0.401 1.151,0.653 false 2.729,0.961 2.944,1.164 0.215,0.203 10 *2 2.69,1.047 2.528,1.047 2.528,1.047 2.276,1.277 false

Connect the hose with an inside diameter of 15 mm (0.59 in.) to the pipe.

Text in Illustration
*1 Pipe
*2 Hose


b.
A127997

Remove the oil filter drain plug from the oil filter cap.


c.
A160741E08
1.885,2.292 2.25,2.292 2.25,2.292 2.771,1.656 false 1.865,2.656 2.104,2.656 2.104,2.656 2.802,1.813 false 1.875,2.948 2.031,2.948 2.031,2.948 2.906,1.896 false 1.698,2.219 1.885,2.375 0.188,0.156 10 false *1 1.688,2.573 1.875,2.729 0.188,0.156 10 false *2 1.698,2.875 1.885,3.031 0.188,0.156 10 false *3

Insert the pipe with the hose into the oil filter cap.

Text in Illustration
*1 Cap
*2 O-ring
*3 Pipe

NOTICE:

Be sure to insert the pipe with the O-ring installed on the oil filter cap side.


HINT:

Place the hose end into a container before draining oil from the hose.



d.
A127999

Make sure that the oil is completely drained, and remove the pipe and O-ring.

HINT:

Be sure to turn the pipe in the direction of the arrow to remove it.



e.
A128000E01
2.357,1.456 2.662,1.595 0.305,0.139 10 SST 1.966,1.542 2.331,1.542 false

Using SST, remove the oil filter cap.

SST
09228-06501  


f.
A128001E15
2,0.74 2.427,0.104 2.427,0.104 2.615,0.104 false 2.167,1.385 2.385,1.604 2.385,1.604 2.615,1.604 false 2.583,0.854 2.51,0.854 2.51,0.854 2.281,1.031 false 2.656,0.052 2.844,0.229 0.188,0.177 10 false *1 2.625,0.792 2.813,0.969 0.188,0.177 10 false *2 2.656,1.531 2.844,1.708 0.188,0.177 10 false *3

Remove the oil filter element and O-ring from the oil filter cap.

Text in Illustration
*1 Oil Filter Element
*2 Oil Filter Cap
*3 O-ring

NOTICE:

Do not use any tools to remove the O-ring in order to prevent the cap from being damaged. Be sure to remove it by hand.



Hide 04152 4.INSTALL OIL FILTER ELEMENT

a.

Clean the inside of the oil filter cap, threads, and O-ring groove.


b.
A268595E15
1.674,0.732 1.835,0.881 0.162,0.149 10 *1 1.52,1.046 1.586,0.819 1.586,0.819 1.667,0.819 false 3.238,0.835 3.399,0.984 0.162,0.149 10 *1 3.089,1.16 3.15,0.922 3.15,0.922 3.231,0.922 false 0.873,1.8 1.038,1.952 0.165,0.152 10 *a 2.434,1.8 2.599,1.952 0.165,0.152 10 *b

Apply a light coat of engine oil to a new O-ring and install it to the oil filter cap.

Text in Illustration
*1 O-ring
*a CORRECT
*b INCORRECT

NOTICE:
·

Be sure to install the O-ring in the proper location, otherwise oil may leak.

·

Do not twist the O-ring.




c.

Install a new oil filter element to the oil filter cap.


d.

Remove all dirt and foreign matter from the installation surface and the inside of the cap on the engine side.


e.

Apply a light coat of engine oil to the O-ring again and install the oil filter cap.

NOTICE:

Make sure that the O-ring does not get caught between the parts.



f.
A275939E01
2.967,1.198 3.151,1.374 0.184,0.176 10 *a 2.644,1.544 2.828,1.720 0.184,0.176 10 *1 2.403,1.609 2.617,1.609 false 2.763,0.724 2.947,0.901 0.184,0.176 10 *2 2.75,0.818 2.668,0.818 2.668,0.818 2.472,1.026 false 2.556,0.379 2.769,0.379 false 2.782,0.289 2.966,0.465 0.184,0.176 10 *3 0.045,1.243 0.369,1.422 0.323,0.178 10 SST 0.617,1.337 0.396,1.337 false

Using SST, install the oil filter cap.

Text in Illustration
*1 Oil Filter Cap
*2 O-ring
*3 Oil Filter Bracket
*a No Gap

SST
09228-06501  

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:

After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.



g.
A161390E10
2.979,1.833 2.177,1.833 false 2.021,1.75 2.219,1.927 0.198,0.177 10 false *1

Apply a light coat of engine oil to a new O-ring and install it to the oil filter cap.

Text in Illustration
*1 O-ring

NOTICE:

Remove all dirt and foreign matter from the installation surface.



h.

Install the oil filter drain plug to the oil filter cap.

Torque:
13 N*m (127 kgf*cm, 10 ft.*lbf)

NOTICE:

Make sure that the O-ring does not get caught between the parts.



Hide 5.ADD ENGINE OIL

a.

Add clean engine oil and install the oil filler cap.

Standard Oil Grade
Oil Grade Oil Viscosity (SAE)

API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil


·

5W-30

·

10W-30


API grade SL, SM or SN multigrade engine oil
·

15W-40

·

20W-50



Standard Oil Grade (Destination package for China)
Oil Grade Oil Viscosity (SAE)

API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil


·

0W-20

·

5W-20

·

5W-30

·

10W-30


API grade SL, SM or SN multigrade engine oil
·

15W-40

·

20W-50



Standard capacity
Item Standard Condition
Drain and refill with oil filter change 6.1 liters (6.4 US qts, 5.4 lmp. qts)
Drain and refill without oil filter change 5.7 liters (6.0 US qts, 5.0 lmp. qts)
Dry fill 6.8 liters (7.2 US qts, 6.0 lmp. qts)


Hide 6.INSPECT FOR OIL LEAK

a.

Start the engine. Check for engine oil leaks from the connected parts of the oil filter cap and oil filter drain plug.


Hide 51442 7.INSTALL NO. 2 ENGINE UNDER COVER