Home › Engine / Hybrid System › 2AZ-FE LUBRICATION › OIL PUMP
RM24M0E _51 Engine / Hybrid System _059554 2AZ-FE LUBRICATION _0291861 OIL PUMP G

2AZ-FE LUBRICATION  OIL PUMP  INSPECTION  


PROCEDURE

Hide 1.INSPECT OIL JET

a.
A126890

Check the oil jet for damage or clogging.

If necessary, repair the cylinder block.


Hide 15131 2.INSPECT OIL PUMP RELIEF VALVE

a.
A114340

Coat the valve with engine oil, and then check that the valve falls smoothly into the valve hole by its own weight.

If it does not, replace the relief valve. If necessary, replace the oil pump assembly.


Hide 15163 3.INSPECT OIL PUMP ROTOR

a.
B011420

Check the side clearance.

i.

Using a feeler gauge and precision straightedge, measure the clearance between the rotors and precision straightedge.

Standard clearance:

0.030 to 0.085 mm (0.0001 to 0.003 in.)


Maximum clearance:

0.16 mm (0.0062 in.)


If the side clearance is greater than the maximum, replace the oil pump assembly.



b.
A114223E01
1.772,0.103 2.664,0.287 0.892,0.184 10 Feeler Gauge 0.972,0.44 1.726,0.184 false

Check the tip clearance.

i.

Using a feeler gauge, measure the clearance between the drive rotor and driven rotor tips.

Standard clearance:

0.080 to 0.160 mm (0.0031 to 0.0063 in.)


Maximum clearance:

0.35 mm (0.0138 in.)


If the tip clearance is greater than the maximum, replace the oil pump assembly.



c.
B011422

Check the body clearance.

i.

Using a feeler gauge, measure the clearance between the driven rotor and pump body.

Standard clearance:

0.100 to 0.170 mm (0.0039 to 0.0067 in.)


Maximum clearance:

0.325 mm (0.01128 in.)


If the body clearance is greater than the maximum, replace the oil pump assembly.



Hide 13519 4.INSPECT OIL NO. 2 CHAIN SUB-ASSEMBLY AND 2 OIL PUMP SPROCKETS

a.
A132684E03
1.667,0.93 2.913,1.099 1.246,0.170 10 Measurement Area 0.452,1.04 1.137,1.205 0.685,0.165 10 102.2 mm 2.92,0.069 3.319,0.232 0.400,0.162 10 140 N 1.599,1.016 1.408,1.426 false

Using a spring scale and vernier caliper, measure a 15 link section of the chain when it is stretched with a force of 140 N (14.3 kgf, 32 lbf).

Maximum chain elongation:

102.2 mm (4.024 in.)


If the elongation is greater than the maximum, replace the No. 2 chain sub-assembly.

HINT:

Take the measurement at 3 or more places and average the measurements to determine the length.



b.

Wrap the chain around the oil pump sprocket.


c.
A126892

Using a vernier caliper, measure the sprocket diameter with the chain.

Minimum sprocket diameter (with chain):

Crankshaft 48.2 mm (1.898 in.)

Oil pump drive shaft 48.2 mm (1.898 in.)


NOTICE:

Vernier caliper must contact the chain rollers when measuring.


If the diameter is less than the minimum, replace the chain and sprockets.


Hide 13549 5.INSPECT CHAIN TENSIONER PLATE

A126893E01
2.986,1.364 3.351,1.526 0.364,0.163 10 Wear

a.

Measure the chain tensioner plate wear.

Maximum wear:

0.5 mm (0.020 in.)


If the wear is greater than the maximum, replace the chain tensioner plate.