Home › Brake › BRAKE › REAR BRAKE
RM24M0E _54 Brake _059558 BRAKE _0291879 REAR BRAKE A

BRAKE  REAR BRAKE  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the LH side and RH side.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 04466 1.REMOVE REAR DISC BRAKE PAD SUB-ASSEMBLY

a.

Remove the 2 disc brake pads.


Hide 47716 2.REMOVE REAR DISC BRAKE PAD SUPPORT PLATE

a.

Place tags or marks to identify the installation locations of each plate.

NOTICE:

As each pad support plate has its own shape, be sure to identify each one accurately when reinstalling it to prevent improper installation.



b.

Remove the 4 plates from the brake cylinder mounting.


Hide 47722A 3.REMOVE REAR DISC BRAKE CYLINDER MOUNTING LH

a.
C138949

Remove the 2 bolts and cylinder mounting.


Hide 47715D 4.REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C138950

Remove the 2 pins (upper and lower) from the mounting.


b.
C138961E02
2.177,1.375 2.313,1.208 false 1.552,1.135 1.281,1.135 1.281,1.135 1.115,1.281 false 2.375,1.823 2.021,1.823 false 0.188,1.292 1.385,1.5 1.198,0.208 10 false Slide Pin (Lower) 1.271,1.74 2.042,1.958 0.771,0.219 10 false Slide Bush 2.365,1.094 3.063,1.333 0.698,0.24 10 false Vinyl Tape

Using a screwdriver, remove the slide bush from the pin (lower).

NOTICE:

Be careful not to damage the pin.


HINT:

Tape the screwdriver tip before use.



Hide 47775 5.REMOVE REAR DISC BRAKE BUSH DUST BOOT

a.
C138951

Remove the 2 boots from the mounting.


Hide 6.REMOVE CYLINDER BOOT

a.
C138952E02
0.875,1.073 0.688,1.469 false 2.677,1.521 2.531,1.875 2.531,1.875 2.219,1.875 false 0.104,1.479 0.865,1.656 0.76,0.177 10 false Vinyl Tape 1.51,1.781 2.271,1.958 0.76,0.177 10 false Vinyl Tape

Using a screwdriver, pry out the boot.

NOTICE:

Be careful not to damage the brake piston and cylinder.


HINT:

Tape the screwdriver tip before use.



Hide 47731 7.REMOVE REAR DISC BRAKE PISTON

a.
C138953E01
2.468,0.58 2.888,0.754 0.420,0.174 10 Cloth 2.119,0.941 2.268,0.66 2.268,0.66 2.417,0.66 false

Place a piece of cloth between the piston and disc brake cylinder.


b.

Apply compressed air to remove the piston from the disc brake cylinder.

CAUTION:

Do not place your fingers in front of the piston when applying compressed air.


NOTICE:

Be careful not to spatter the brake fluid.



Hide 8.REMOVE PISTON SEAL

a.
C138954E01
2.457,0.591 3.205,0.794 0.748,0.202 10 Vinyl Tape 1.718,1.445 2.119,0.689 2.119,0.689 2.422,0.689 false

Using a screwdriver, pry out the seal from the cylinder.

NOTICE:

Be careful not to damage the inner cylinder and piston seal groove.


HINT:

Tape the screwdriver tip before use.



Hide 47547C 9.REMOVE REAR DISC BRAKE BLEEDER PLUG

a.

Remove the bleeder plug cap and bleeder plug from the cylinder.


Hide 42491 10.REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

a.

Remove the shoe adjusting hole plug from the rear disc.


Hide 42431 11.REMOVE REAR DISC

a.
C133389E03
2.462,0.05 3.243,0.227 0.781,0.177 10 Matchmark 1.821,1.035 2.405,0.162 2.405,0.162 1.815,1.179 false

Put matchmarks on the disc and axle hub.


b.

Release the parking brake.


c.
C133390

Turn the shoe adjuster until the disc turns freely, and then remove the disc.