Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM
RM24M0E _55 Steering _059560 STEERING COLUMN _0291889 STEERING LOCK SYSTEM J

STEERING COLUMN  STEERING LOCK SYSTEM  Power Source Circuit  


DESCRIPTION

This circuit supplies power source voltage from the battery to terminal B of the steering lock actuator.

The diagnosis information of the steering lock ECU is transmitted to the tester via the certification ECU as the steering lock ECU is not connected to the CAN communication system.

WIRING DIAGRAM

C136915E06
1.115,1.073 1.875,1.25 0.76,0.177 10 false STRG LCK 0.667,2.156 1.229,2.292 0.563,0.135 10 false MAIN 2.5,0.917 2.625,1.083 0.125,0.167 10 false B 3.292,0.917 3.719,1.063 0.427,0.146 10 false SLP1 3.24,1.552 3.708,1.729 0.469,0.177 10 false SGND 3.323,2.063 3.708,2.219 0.385,0.156 10 false GND 2.406,2.771 3.854,3.198 1.448,0.427 10 false Steering Lock Actuator (Steering Lock ECU) 5.552,0.938 5.938,1.125 0.385,0.188 10 false SLP 5.604,2.594 6.677,2.771 1.073,0.177 10 false Main Body ECU 0.688,1.479 1.677,1.688 0.99,0.208 10 false RH R/B BATT 2.281,0.792 2.469,0.979 0.188,0.188 10 false 7 3.781,0.802 3.979,0.99 0.198,0.188 10 false 4 3.781,1.448 3.979,1.646 0.198,0.198 10 false 2 3.771,1.927 3.927,2.104 0.156,0.177 10 false 1 5.229,0.729 5.448,0.917 0.219,0.188 10 false 18 5.198,0.927 5.5,1.083 0.302,0.156 10 false G57 5.542,2.052 5.979,2.229 0.438,0.177 10 false GND2 5.24,2.052 5.448,2.219 0.208,0.167 10 false 4A 5.292,1.844 5.406,2 0.115,0.156 10 false 3 2.406,2.583 2.865,2.781 0.458,0.198 10 false G32

CAUTION / NOTICE / HINT

HINT:

When the ignition switch is off, the main body ECU may occasionally go into a non-active state called sleep mode. Therefore, before proceeding with the inspection, it is necessary to perform the following step to wake up the ECU:

Before starting the inspection, with the ignition switch off, open the driver door. Then (with the ignition switch still off) open and close any door several times at 1.5 second intervals.


PROCEDURE

1.CHECK WIRE HARNESS (STEERING LOCK ACTUATOR - BODY GROUND)
U188962E01
0.102,0.069 1.688,0.266 1.586,0.198 10 Wire Harness Side: 1.619,1.783 2.081,1.939 0.461,0.156 10 SGND 0.485,1.68 0.835,1.836 0.350,0.156 10 GND 1.109,1.282 0.731,1.66 false 1.389,1.292 1.883,1.752 false 0.335,1.096 0.643,1.328 0.309,0.232 10 G32

a.

Disconnect the G32 steering lock actuator connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
G32-1 (GND) - Body ground Below 1 Ω
G32-2 (SGND) - Body ground Below 1 Ω




OK

2.CHECK WIRE HARNESS (BATTERY - STEERING LOCK ACTUATOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK WIRE HARNESS (BATTERY - STEERING LOCK ACTUATOR)
U188963E01
0.111,0.044 1.726,0.200 1.614,0.156 10 Wire Harness Side: 2.734,1.379 2.885,1.535 0.151,0.156 10 B 2.32,1.263 2.712,1.429 false 0.448,1.043 0.756,1.254 0.309,0.211 10 G32

a.

Disconnect the G32 steering lock actuator connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
G32-7 (B) - Body ground 10 to 14 V




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR