Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM
RM24M0E _55 Steering _059560 STEERING COLUMN _0291889 STEERING LOCK SYSTEM D

STEERING COLUMN  STEERING LOCK SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


a.

When troubleshooting a vehicle with a diagnosis system, connect the intelligent tester to the DLC3 of the vehicle and read various data output from the steering lock ECU.

The steering lock ECU records DTCs when the ECU detects a malfunction in itself or in its circuits.


b.

The diagnosis information of the steering lock ECU is transmitted to the tester via the certification ECU as the steering lock ECU is not connected to the CAN communication system.


c.

The steering lock ECU does not store DTCs regarding past problems.

HINT:

When the ignition switch is off, the main body ECU to which the intelligent tester is to be connected may be malfunctioning or in sleep mode.

Communication with the intelligent tester is impossible if the main body ECU is not working.



d.

As the steering lock ECU's memory data will be deleted, do not remove the fuses or disconnect the battery terminals until the DTCs are checked and noted.


e.

Malfunctions related to systems other than the steering lock ECU's system may cause DTCs to be output. Note any DTCs related to other systems.



CHECK DLC3


a.
H103023E07
1.708,1.875 1.948,1.469 true 1.563,0.917 1.208,0.438 true 1.76,0.927 1.542,0.448 true 1.948,0.927 2.031,0.448 true 2.135,0.927 2.427,0.458 true 2.458,1.896 2.313,1.479 true 1.031,0.25 1.281,0.427 0.25,0.177 10 false CG 1.427,1.906 1.896,2.094 0.469,0.188 10 false CANL 1.396,0.25 1.646,0.427 0.25,0.177 10 false SG 1.813,0.229 2.271,0.396 0.458,0.167 10 false CANH 2.417,0.229 2.677,0.406 0.26,0.177 10 false SIL 2.333,1.917 2.802,2.104 0.469,0.188 10 false BAT

The certification ECU follows the ISO 15765-4 communication protocol. The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format.

Symbols (Terminal No.) Terminal Description Condition Specified Condition
SIL (7) - SG (5) Bus "+" line During transmission Pulse generation
CG (4) - Body ground Chassis ground Always Below 1 Ω
SG (5) - Body ground Signal ground Always Below 1 Ω
BAT (16) - Body ground Battery positive Always 11 to 14 V
CANH (6) - CANL (14) CAN bus line Ignition switch off* 54 to 69 Ω
CANH (6) - BAT (16) HIGH-level CAN bus line Ignition switch off* 6 kΩ or higher
CANH (6) - CG (4) HIGH-level CAN bus line Ignition switch off* 200 Ω or higher
CANL (14) - BAT (16) LOW-level CAN bus line Ignition switch off* 6 kΩ or higher
CANL (14) - CG (4) LOW-level CAN bus line Ignition switch off* 200 Ω or higher

NOTICE:

*: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors.


If the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness and connector.


HINT:

Connect the cable of the intelligent tester to the DLC3, turn the ignition switch on (IG) and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.

·

If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.

·

If communication is still not possible when the tester is connected to another vehicle, the problem may be in the tester itself. Consult the Service Department listed in the tester's instruction manual.