Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM
RM24M0E _55 Steering _059560 STEERING COLUMN _0291889 STEERING LOCK SYSTEM C

STEERING COLUMN  STEERING LOCK SYSTEM  B2785  Communication Malfunction between ECUs Connected by LIN  


DESCRIPTION

This DTC is output when LIN communication from the certification ECU stops for a certain amount of time.

DTC No. DTC Detection Condition Trouble Area
B2785 LIN communication from certification ECU stops for certain amount of time
·

Open or short in wire harness between ECUs


·

Wire harness

·

Certification ECU

·

ID code box

·

Main body ECU

·

Steering lock ECU (Steering lock actuator)



WIRING DIAGRAM

C136903E06
0.927,2.635 2.031,3.073 1.104,0.438 10 false G29 5.281,2.635 6.396,3.083 1.115,0.448 10 false 4A 3.083,5.104 4.281,5.26 1.198,0.156 10 false Junction Block LH 1.854,1.677 2.229,1.885 0.375,0.208 10 false LIN 5.24,1.667 5.729,1.885 0.49,0.219 10 false LIN1 1.854,4.646 2.229,4.854 0.375,0.208 10 false LIN 5.219,4.635 5.708,4.854 0.49,0.219 10 false LIN1 0.74,5.615 2.24,6.469 1.5,0.854 10 false G32 5.448,5.615 6.302,6.01 0.854,0.396 10 false G20 2.188,1.542 2.396,1.75 0.208,0.208 10 false 10 2.229,4.542 2.406,4.75 0.177,0.208 10 false 5 5,4.531 5.24,4.771 0.24,0.24 10 false 3 4.896,1.552 5.073,1.771 0.177,0.219 10 false 20 2.823,1.667 3.031,1.865 0.208,0.198 10 false LB 4.229,1.656 4.51,1.885 0.281,0.229 10 false LA 4.271,1.469 4.479,1.688 0.208,0.219 10 false 5 4.229,4.646 4.479,4.854 0.25,0.208 10 false LC 2.833,4.646 3.115,4.875 0.281,0.229 10 false LA 2.865,1.458 3.073,1.677 0.208,0.219 10 false 6 4.271,4.448 4.479,4.667 0.208,0.219 10 false 6 2.875,4.438 3.083,4.656 0.208,0.219 10 false 6 0.927,2.802 2.031,3.24 1.104,0.438 10 false Certification ECU 5.281,2.802 6.396,3.25 1.115,0.448 10 false Main Body ECU 0.74,5.792 2.156,6.417 1.417,0.625 10 false Steering Lock Actuator (Steering Lock ECU) 5.448,5.781 6.302,6.177 0.854,0.396 10 false ID Code Box

CAUTION / NOTICE / HINT

HINT:

When the ignition switch is off, the main body ECU may occasionally go into a non-active state called sleep mode. Therefore, before proceeding with the inspection, it is necessary to perform the following step to wake up the ECU:

Before starting the inspection, with the ignition switch off, open the driver door. Then (with the ignition switch still off) open and close any door several times at 1.5 second intervals.


NOTICE:

If the steering lock actuator (steering lock ECU) is replaced, with the ignition switch off and the shift lever on P, open and close the driver side door to record the current lock position into the steering lock ECU. If this is not performed, the engine may not start.


PROCEDURE

1.CHECK DTC (CERTIFICATION ECU)
a.

Clear the DTC.


b.

Recheck for DTC.

Result
Result Proceed to
B2785 output reoccurs A
B2785 output does not reoccur B



A

2.CHECK JUNCTION BLOCK LH

B

NORMAL

2.CHECK JUNCTION BLOCK LH
a.

Disconnect the LA, LB and LC junction block LH connectors.


U189685E02
0.76,1.302 1.396,1.5 false 1.396,1.635 0.76,1.625 false 1.406,1.802 0.771,1.979 false 0.542,1.167 0.833,1.406 0.292,0.24 10 false LA 0.521,1.542 0.813,1.781 0.292,0.24 10 false LB 0.542,1.906 0.833,2.146 0.292,0.24 10 false LC

b.

Measure the resistance of the junction block LH.

Standard resistance:
Tester Connection Specified Condition
LB-6 - LA-5 Below 1 Ω
LB-6 - LA-6 Below 1 Ω
LB-6 - LC-6 Below 1 Ω
LB-6 - Body ground 10 kΩ or higher




OK

3.CHECK WIRE HARNESS (LIN COMMUNICATION LINE)

NG

REPAIR OR REPLACE JUNCTION BLOCK LH

3.CHECK WIRE HARNESS (LIN COMMUNICATION LINE)
U189686E02
2.688,6.938 3.667,7.448 false 1.781,5.302 0.802,5.677 false 5.698,6.938 6.385,6.635 false 5.323,5.292 4.656,5.521 false 0.281,0.073 2.469,0.292 2.188,0.219 10 false Wire Harness Side: 4.146,3.708 5.313,4.083 1.167,0.375 10 false Junction Block LH 0.594,1.167 1.125,1.448 0.531,0.281 10 false LA 0.583,2.229 1.115,2.51 0.531,0.281 10 false LB 0.573,3.083 1.104,3.365 0.531,0.281 10 false LC 1.646,5.656 2.698,5.896 1.052,0.24 10 false Main Body ECU 1.979,4.458 2.51,4.74 0.531,0.281 10 false 4A 1.667,7.406 2.802,7.667 1.135,0.26 10 false Certification ECU 2.063,6.271 2.594,6.552 0.531,0.281 10 false G29 3.698,7.458 4.094,7.677 0.396,0.219 10 false LIN 0.49,5.656 1.021,5.896 0.531,0.24 10 false LIN1 4.792,7.365 6.323,7.708 1.531,0.344 10 false Steering Lock Actuator 5.344,6.271 5.875,6.552 0.531,0.281 10 false G32 5.156,5.51 6.031,5.76 0.875,0.25 10 false ID Code Box 5.365,4.51 5.896,4.792 0.531,0.281 10 false G20 6.438,6.552 6.885,6.75 0.448,0.198 10 false LIN 4.344,5.479 4.823,5.708 0.479,0.229 10 false LIN1

a.

Disconnect the G29 certification ECU connector.


b.

Disconnect the G32 steering lock actuator connector.


c.

Disconnect the G20 ID code box connector.


d.

Disconnect the 4A main body ECU connector.


e.

Disconnect the LA, LB and LC junction block LH connectors.


f.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G29-10 (LIN) - LB-6 Below 1 Ω
G29-10 (LIN) or LB-6 - Body ground 10 kΩ or higher
4A-20 (LIN1) - LA-6 Below 1 Ω
4A-20 (LIN1 ) or LA-6 - Body ground 10 kΩ or higher
G32-5 (LIN) - LA-5 Below 1 Ω
G32-5 (LIN) or LA-5 - Body ground 10 kΩ or higher
G20-3 (LIN1) - LC-6 Below 1 Ω
G20-3 (LIN1) or LC-6 - Body ground 10 kΩ or higher




OK

4.CHECK OPERATION OF CERTIFICATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK OPERATION OF CERTIFICATION ECU
a.

Replace the certification ECU with a normally functioning or new one.


b.

Check for DTC.

Result
Result Proceed to
B2785 output reoccurs A
B2785 output does not reoccur B



A

5.CHECK OPERATION OF MAIN BODY ECU

B

REPLACE CERTIFICATION ECU

5.CHECK OPERATION OF MAIN BODY ECU
a.

Replace the main body ECU with a normally functioning or new one.


b.

Check for DTC.

Result
Result Proceed to
B2785 output reoccurs A
B2785 output does not reoccur B



A

6.CHECK OPERATION OF STEERING LOCK ECU

B

REPLACE MAIN BODY ECU

6.CHECK OPERATION OF STEERING LOCK ECU
a.

Replace the steering lock actuator with a normally functioning or new one.


b.

Check for DTC.

Result
Result Proceed to
B2785 output reoccurs A
B2785 output does not reoccur B



A

REPLACE ID CODE BOX

B

REPLACE STEERING LOCK ACTUATOR