Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM
RM24M0E _55 Steering _059560 STEERING COLUMN _0291889 STEERING LOCK SYSTEM C

STEERING COLUMN  STEERING LOCK SYSTEM  B2786  No Response from Steering Lock ECU  


DESCRIPTION

This DTC is output when the certification ECU does not receive LIN communication from the steering lock ECU for 10 seconds.

The diagnosis information of the steering lock ECU is transmitted to the tester via the certification ECU as the steering lock ECU is not connected to the CAN communication system.

DTC No. DTC Detection Condition Trouble Area
B2786 Certification ECU does not receive LIN communication from steering lock ECU for 10 seconds
·

Wire harness

·

Certification ECU

·

Steering lock actuator (Steering lock ECU)



WIRING DIAGRAM

C136906E06
0.708,2.406 2.167,3.063 1.458,0.656 10 false G32 3.042,2.469 4.25,2.656 1.208,0.188 10 false Junction Block LH 5.208,2.406 6.354,2.885 1.146,0.479 10 false G29 2.021,1.458 2.281,1.625 0.26,0.167 10 false LIN 4.979,1.458 5.24,1.625 0.26,0.167 10 false LIN 4.052,1.448 4.292,1.635 0.24,0.188 10 false LB 4.073,1.271 4.198,1.417 0.125,0.146 10 false 6 4.698,1.354 4.875,1.552 0.177,0.198 10 false 10 2.979,1.448 3.198,1.635 0.219,0.188 10 false LA 3.031,1.26 3.188,1.469 0.156,0.208 10 false 6 2.375,1.354 2.573,1.531 0.198,0.177 10 false 5 0.708,2.573 2.167,3.229 1.458,0.656 10 false Steering Lock Actuator (Steering Lock ECU) 5.208,2.573 6.354,3.052 1.146,0.479 10 false Certification ECU

CAUTION / NOTICE / HINT

HINT:

When the ignition switch is off, the main body ECU may occasionally go into a non-active state called sleep mode. Therefore, before proceeding with the inspection, it is necessary to perform the following step to wake up the ECU:

Before starting the inspection, with the ignition switch off, open the driver door. Then (with the ignition switch still off) open and close any door several times at 1.5 second intervals.


NOTICE:

If the steering lock actuator (steering lock ECU) is replaced, with the ignition switch off and the shift lever on P, open and close the driver side door to record the current lock position into the steering lock ECU. If this is not performed, the engine may not start.


PROCEDURE

1.CHECK DTC (CERTIFICATION ECU)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and press the intelligent tester main switch ON.


c.

Clear the DTCs of the certification ECU by following the prompts displayed on the intelligent tester.


d.

Recheck for DTC.

Result
Result Proceed to
B2786 output reoccurs A
B2786 output does not reoccur B



A

2.CHECK JUNCTION BLOCK LH

B

NORMAL (CHECK FOR INTERMITTENT PROBLEM)

2.CHECK JUNCTION BLOCK LH
a.

Disconnect the LA and LB junction block LH connectors.


U189673E02
0.781,1.26 1.417,1.5 false 1.417,1.646 0.781,1.74 false 0.49,1.167 0.844,1.354 0.354,0.188 10 false LA 0.5,1.656 0.854,1.844 0.354,0.188 10 false LB

b.

Measure the resistance of the junction block LH.

Standard resistance:
Tester Connection Specified Condition
LA-6 - LB-6 Below 1 Ω
LA-6 or LB-6 - Body ground 10 kΩ or higher




OK

3.CHECK WIRE HARNESS (CERTIFICATION ECU - STEERING LOCK ECU)

NG

REPAIR OR REPLACE JUNCTION BLOCK LH

3.CHECK WIRE HARNESS (CERTIFICATION ECU - STEERING LOCK ECU)
U189687E02
5.708,4.688 6.552,4.292 false 2.844,4.646 3.427,3.958 false 0.281,0.052 2.385,0.385 2.104,0.333 10 false Wire Harness Side: 4.302,0.469 5.542,0.792 1.24,0.323 10 false Junction Block LH 0.74,1.083 1.302,1.396 0.563,0.313 10 false LA 0.729,2.135 1.292,2.448 0.563,0.313 10 false LB 2.271,3.938 2.833,4.25 0.563,0.313 10 false G29 5.448,3.979 6.01,4.292 0.563,0.313 10 false G32 1.729,5.177 2.885,5.427 1.156,0.25 10 false Certification ECU 4.875,5.125 6.333,5.396 1.458,0.271 10 false Steering Lock Actuator 3.469,3.823 4.24,4.094 0.771,0.271 10 false LIN 6.594,4.198 7.063,4.396 0.469,0.198 10 false LIN

a.

Disconnect the G29 certification ECU connector.


b.

Disconnect the G32 steering lock actuator connector.


c.

Disconnect the LA and LB junction block LH connectors.


d.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G29-10 (LIN) - LB-6 Below 1 Ω
G29-10 (LIN) or LB-6 - Body ground 10 kΩ or higher
G32-5 (LIN) - LB-6 Below 1 Ω
G32-5 (LIN) or LB-6 - Body ground 10 kΩ or higher




OK

4.CHECK OPERATION OF CERTIFICATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK OPERATION OF CERTIFICATION ECU
a.

Replace the certification ECU with a normally functioning or new one.


b.

Check for DTC.

Result
Result Proceed to
B2786 output reoccurs A
B2786 output does not reoccur B



A

REPLACE STEERING LOCK ACTUATOR

B

REPLACE CERTIFICATION ECU