Home › Steering › POWER STEERING › POWER STEERING SYSTEM
RM24M0E _55 Steering _059561 POWER STEERING _0291895 POWER STEERING SYSTEM D

POWER STEERING  POWER STEERING SYSTEM  DIAGNOSIS SYSTEM  


CHECK DLC3


H103023E07
1.708,1.875 1.948,1.469 true 1.563,0.917 1.208,0.438 true 1.76,0.927 1.542,0.448 true 1.948,0.927 2.031,0.448 true 2.135,0.927 2.427,0.458 true 2.458,1.896 2.313,1.479 true 1.031,0.25 1.281,0.427 0.25,0.177 10 false CG 1.427,1.906 1.896,2.094 0.469,0.188 10 false CANL 1.396,0.25 1.646,0.427 0.25,0.177 10 false SG 1.813,0.229 2.271,0.396 0.458,0.167 10 false CANH 2.417,0.229 2.677,0.406 0.26,0.177 10 false SIL 2.333,1.917 2.802,2.104 0.469,0.188 10 false BAT

The ECU uses ISO15765-4 for communication. The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format. if the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness and connector.

Symbols (Terminal No.) Terminal Description Condition Specified Condition
SIL (7) - SG (5) Bus [+] line During transmission Pulse generation
CG (4) - Body ground Chassis ground Always Below 1 Ω
SG (5) - Body ground Signal ground Always Below 1 Ω
BAT (16) - Body ground Battery positive Always 11 to 14 V
CANH (6) - CANL (14) CAN bus line Ignition switch off* 54 to 69 Ω
CANH (6) - BAT (16) HIGH-level CAN bus line Ignition switch off* 6 kΩ or higher
CANH (6) - CG (4) HIGH-level CAN bus line Ignition switch off* 200 Ω or higher
CANL (14) - BAT (16) LOW-level CAN bus line Ignition switch off* 6 kΩ or higher
CANL (14) - CG (4) LOW-level CAN bus line Ignition switch off* 200 Ω or higher

NOTICE:

*: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors.


HINT:

If the display shows [UNABLE TO CONNECT TO VEHICLE] after connecting the intelligent tester cable to the DLC3 and the ignition switch on (IG), there is a problem either with the vehicle or the tester.

·

If communication is normal when connecting the tester to another vehicle, inspect the DLC3 on the original vehicle.

·

If communication is still not possible when connecting the tester to another vehicle, the problem is probably in the tester itself. Consult the Service Department listed in the tester's operator's manual.




CHECK WARNING LIGHT


a.

When a problem occurs in the electronic power steering system, the P/S warning light on the combination meter comes on to inform the driver of the problem.

C223546E01
0.216,0.115 1.504,0.354 1.288,0.239 10 Combination Meter: 0.58,0.633 1.146,0.789 0.566,0.156 10 for LHD: 0.58,2.286 1.146,2.442 0.566,0.156 10 for RHD: 3.007,0.437 4.190,0.648 1.184,0.211 10 P/S Warning Light 3.007,2.095 4.190,2.306 1.184,0.211 10 P/S Warning Light