READ DATA LIST
Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and press the intelligent tester main switch ON.
Read the Data List by following the directions on the tester screen.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Meter Vehicle Velocity | Vehicle speed from meter:
Min.: 0 km/h (0 mph) Max.: 300 km/h (187.5 mph) |
0 km/h (0 mph) | Vehicle stopped |
| No significant fluctuation | Vehicle driven at a constant speed | ||
| Spd Sig Invalid Record | Record of vehicle speed signal invalid:
REC or UNREC |
UNREC | - |
| Engine Revolution | Show the engine revolution:
Min.: 0 rpm Max.: 12800 rpm |
No significant fluctuation | Engine is running at a constant speed |
| Eng Rev Inter Record | Record of engine revolution signal interruption:
REC or UNREC |
UNREC | - |
| Motor Actual Current | Amount of current to motor:
Min.: -327.68 A Max.: 327.67 A |
Value changes in proportion to steering effort | Power steering is in operation |
| Command Value Current | Demanded amount of current to motor:
Min.: -327.68 A Max.: 327.67 A |
Value changes in proportion to steering effort | Power steering is in operation |
| Command Val Current 2 | Demanded amount of current to motor:
Min.: -327.68 A Max.: 327.67 A |
Value changes in proportion to steering effort | Power steering is in operation |
| Steering Angle Velocity | Steering angle speed:
Min.: -327.68°/sec. Max.: 327.67°/sec. |
Value changes in proportion to steering effort | Steering wheel is turned |
| Steering Wheel Torque | Steering wheel torque:
Min.: -327.68 Nm Max.: 7 Nm |
Value changes in proportion to steering effort | Ignition switch on (IG)
Power steering is in operation |
| Thermistor Temperature | ECU substrate temperature:
Min.: -40°C Max.: 150°C |
- | Ignition switch on (IG) |
| PIG Power Supply | Power source voltage to active motor:
Min.: 0 V Max.: 20.1531 V |
10 to 14 V | Power steering is in operation |
| IG Power Supply | ECU power source voltage:
Min.: 0 V Max.: 20.1531 V |
10 to 14 V | Ignition switch on (IG) |
| Motor Overheat Record | Continuous overheat prevention control record:
REC or UNREC |
PIG power source voltage drop record:
REC or UNREC |
- |
| Motor Lo Power Record | PIG power source voltage drop record:
REC or UNREC |
UNREC | - |
| Motor Rotation Angle | Motor rotation angle:
Min.: 0° Max.: 1441.79° |
During steering operation, motor rotation angle value changes from 0 to 360° | Power steering in operation |
| Motor Voltage | Motor power supply voltage:
Min.: 0 V Max.: 45.955 V |
Approximately 33 V | Ignition switch on (IG)
Steering wheel is not turned |
| Value changes within 4 to 46 V range | Ignition switch on (IG)
Steering wheel is turned |
||
| Motor Terminal Volt (U) | Motor terminal voltage (U phase):
Min.: 0 V Max.: 46.667 V |
Value changes within 4 to 46 V range | Ignition switch on (IG)
Steering wheel is turned |
| Motor Terminal Volt (V) | Motor terminal voltage (V phase):
Min.: 0 V Max.: 46.667 V |
Value changes within 4 to 46 V range | Ignition switch on (IG)
Steering wheel is turned |
| Motor Terminal Volt (W) | Motor terminal voltage (W phase):
Min.: 0 V Max.: 46.667 V |
Value changes within 4 to 46 V range | Ignition switch on (IG)
Steering wheel is turned |
| PIG2 Voltage | Coil rear pressurization voltage:
Min.: 0 V Max.: 45.955 V |
Approximately 33 V | Ignition switch on (IG)
Steering wheel is not turned |
| Value changes within 4 to 46 V range | Ignition switch on (IG)
Steering wheel is turned |
||
| IG ON/OFF Times | Ignition switch ON / OFF number of times after fail detection:
Min.: 0 time Max.: 65535 times |
- | - |
| The Number of DTCs | Number of detected DTCs when freeze frame data stored:
Min.: 0 Max.: 255 |
- | - |
| PS Assist Signal | Power steering assist signal:
ON or OFF |
OFF | No steering load (in neutral position) |
| ON | Ignition switch on (IG)
Steering wheel is turned |
||
| Torque Sensor 1 Output | Torque sensor voltage:
Min.: 0 V Max.: 5 V |
2.3 to 2.7 V | Ignition switch on (IG)
Steering wheel not turned (without load) |
| 2.5 to 3.8 V | Ignition switch on (IG)
Steering wheel turned to right with vehicle stopped |
||
| 1.2 to 2.5 V | Ignition switch on (IG)
Steering wheel turned to left with vehicle stopped |
||
| Torque Sensor 2 Output | Torque sensor voltage:
Min.: 0 V Max.: 5 V |
2.3 to 2.7 V | Ignition switch on (IG)
Steering wheel not turned (without load) |
| 1.2 to 2.5 V | Ignition switch on (IG)
Steering wheel turned to right with vehicle stopped |
||
| 2.5 to 3.8 V | Ignition switch on (IG)
Steering wheel turned to left with vehicle stopped |
||
| TRQ1 Zero Point Value | Torque sensor voltage:
Min.: 0 V Max.: 5 V |
Values differ depending on vehicle | Steering wheel is not turned |
| TRQ2 Zero Point Value | Torque sensor voltage:
Min.: 0 V Max.: 5 V |
Values differ depending on vehicle | Steering wheel is not turned |
| Str Angle Inter Record | Record of steering sensor signal interruption occurrence display:
REC / UNREC |
- | - |
PERFORM ACTIVE TEST
Performing the intelligent tester's Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time. The Data List can be displayed during the Active Test.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester ON.
Perform the Active Test by following the prompts on the tester.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Indicator Light EMPS | P/S indicator | ON / OFF | Confirm that vehicle is stopped, with the engine idling |