Home › Steering › POWER STEERING › POWER STEERING SYSTEM › 2013.04–2014.09
RM24M0E _55 Steering _059561 POWER STEERING _0291895 POWER STEERING SYSTEM D

POWER STEERING  POWER STEERING SYSTEM  CALIBRATION  


ROTATION ANGLE SENSOR INITIALIZATION AND TORQUE SENSOR ZERO POINT CALIBRATION (MANUAL OPERATION)


NOTICE:

Clear the rotation angle sensor calibration value, initialize the rotation angle sensor, and calibrate the torque sensor zero point if any of the following has occurred:

·

The power steering ECU has been replaced.

·

The power steering link has been replaced.

·

Steering effort differs between left and right.



a.

Check for DTC.

i.

Check for DTC (see page Steering>POWER STEERING>POWER STEERING SYSTEM>DTC CHECK / CLEAR).

NOTICE:
·

If DTC C1516 (Torque Sensor Zero Point Adjustment Incomplete) is stored, the torque sensor zero point cannot be calibrated. Clear the DTC before starting calibration.

·

If DTC C1526 (Rotation Angle Sensor Initialization Incomplete) is stored, the rotation angle sensor cannot be initialized. Clear the DTC before starting initialization.

·

If DTCs other than C1516 and C1526 are output, refer to the "DIAGNOSTIC TROUBLE CODE CHART" (see page Steering>POWER STEERING>POWER STEERING SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).





b.

Pre-calibration check

i.

Turn the ignition switch off.


ii.

Disconnect the G91 power steering ECU connector.


iii.

Turn the ignition switch on (IG).


iv.
U189014E02
2.021,1.583 1.583,1.771 false 0.063,0.031 1.458,0.323 1.396,0.292 10 true Wire Harness Side: 1.563,1.375 1.854,1.542 0.292,0.167 10 false G91 1.156,1.771 1.646,1.979 0.49,0.208 10 false 6 (IG)

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Normal Condition
G91-6 (IG) - Body ground 10 V or higher


NOTICE:

If the measured value is 9 V or less, the calibration cannot be performed. Recharge or replace the battery and then perform the calibration.



v.

Turn the ignition switch off.


vi.

Connect the G91 power steering ECU connector.



c.

Erase sensor calibration value

i.

Set the steering wheel to the center point and align the front tires straight ahead.


ii.

Turn the ignition switch off.


iii.
C142044E02
2.101,0.221 2.428,0.446 0.327,0.225 10 CG 2.783,1.728 3.013,1.875 0.230,0.147 10 TC 1.66,0.966 2.044,0.317 false 0.491,1.728 0.700,1.902 0.209,0.174 10 TS 1.62,1.51 0.729,1.728 false 1.846,1.507 2.726,1.757 false

Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:

Connect the terminals to the correct positions to avoid a malfunction.



iv.

Turn the ignition switch on (IG) and then connect and disconnect terminals 13 (TC) and 4 (CG) at least 20 times in 20 seconds.

C143546E17
0.208,0.74 1.833,0.927 1.625,0.188 10 false DLC3 (TS and CG) 1.99,0.552 2.406,0.792 0.417,0.24 10 false Short 1.99,0.948 2.396,1.167 0.406,0.219 10 false Open 0.208,1.49 1.396,1.688 1.188,0.198 10 false Ignition Switch 1.99,1.333 2.531,1.563 0.542,0.229 10 false on (IG) 1.99,1.698 2.302,1.938 0.313,0.24 10 false off 0.208,2.271 1.458,2.458 1.25,0.188 10 false DLC3 (TC and CG) 1.99,2.073 2.406,2.313 0.417,0.24 10 false Short 1.99,2.479 2.396,2.698 0.406,0.219 10 false Open 0.208,3.281 1.406,3.479 1.198,0.198 10 false P/S Warning Light 1.99,3.115 2.292,3.281 0.302,0.167 10 false ON 1.99,3.563 2.302,3.719 0.313,0.156 10 false OFF 0.281,0.052 2.979,0.302 2.698,0.25 10 false Erase sensor calibration value: 3.979,4.427 4.771,4.604 0.792,0.177 10 false 20 seconds 3.198,3.719 4.177,3.896 0.979,0.177 10 false 0.125 seconds 3.26,3.031 4.24,3.208 0.979,0.177 10 false 0.125 seconds 4.313,2.76 5.594,2.948 1.281,0.188 10 false 20 times or more


v.

Check that the P/S warning light blinks and then remains illuminated.

C223546E01
0.216,0.115 1.504,0.354 1.288,0.239 10 Combination Meter: 0.58,0.633 1.146,0.789 0.566,0.156 10 for LHD: 0.58,2.286 1.146,2.442 0.566,0.156 10 for RHD: 3.007,0.437 4.190,0.648 1.184,0.211 10 P/S Warning Light 3.007,2.095 4.190,2.306 1.184,0.211 10 P/S Warning Light

HINT:

The P/S warning light illumination indicates that DTCs C1515 and C1525 have been stored.



vi.

Turn the ignition switch off.

NOTICE:

After erasing the sensor calibration value, the rotation angle sensor initialization or zero point calibration cannot be performed if the ignition switch is on (IG).




d.

Torque sensor zero point calibration

NOTICE:

As the torque sensor zero point calibration cannot be performed if DTC C1515 has not been stored, be sure to perform the sensor calibration value erasure before performing the torque sensor zero point calibration.


i.

Set the steering wheel to the center point and align the front tires straight ahead.


ii.

Turn the ignition switch off.


iii.
C142044E02
2.101,0.221 2.428,0.446 0.327,0.225 10 CG 2.783,1.728 3.013,1.875 0.230,0.147 10 TC 1.66,0.966 2.044,0.317 false 0.491,1.728 0.700,1.902 0.209,0.174 10 TS 1.62,1.51 0.729,1.728 false 1.846,1.507 2.726,1.757 false

Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

SST
09843-18040  


iv.

Turn the ignition switch on (IG) and then connect terminals 13 (TC) and 4 (CG).

NOTICE:

Do not touch the steering wheel during the calibration (for 3 seconds).


HINT:

The P/S warning light remains illuminated even when the calibration has been completed.



v.

With terminals 12 (TS) and 4 (CG), and 13 (TC) and 4 (CG) connected, and the ignition switch on (IG), continue to perform the rotation angle sensor initialization.



e.

Rotation angle sensor initialization

NOTICE:

As the rotation angle sensor initialization cannot be performed if DTC C1525 has not been stored, be sure to perform the sensor calibration value erasure and torque sensor zero point calibration before performing the rotation angle sensor initialization.


HINT:

The rotation angle sensor initialization performs the motor rotation angle sensor.


i.

Set the steering wheel to the center point and align the front tires straight ahead.

NOTICE:

Make sure that terminals 12 (TS) and 4 (CG), and 13 (TC) and 4 (CG) are connected, and the ignition switch is on (IG).



ii.

Disconnect and reconnect terminals 13 (TC) and 4 (CG).

HINT:

Disconnecting and reconnecting terminals 13 (TC) and 4 (CG) allows the power steering ECU to change modes to rotation angle sensor initialization mode



iii.

Turn the steering wheel to the left and right 45° or more. Then turn the steering wheel to the left or right 90° or more.

NOTICE:
·

Do not turn the steering wheel sharply.



HINT:
·

When the calibration has been completed normally, the P/S warning light goes from being illuminated to blinking (at 0.125 second intervals) .

·

The P/S warning light remains illuminated if the calibration has not been completed normally. In this case, check for DTCs and perform calibration again if DTC C1515 and/or C1525 is/are output. When performing the calibration again, perform it in the following order: sensor calibration value erasure, torque sensor zero point calibration, and rotation angle sensor initialization. If DTCs other than C1515 and C1525 are output, go to "DIAGNOSTIC TROUBLE CODE CHART" (see page Steering>POWER STEERING>POWER STEERING SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).




iv.

Disconnect SST from the DLC3.


v.

Turn the ignition switch off.




ROTATION ANGLE SENSOR INITIALIZATION AND TORQUE SENSOR ZERO POINT CALIBRATION (USING INTELLIGENT TESTER)


NOTICE:

Clear the rotation angle sensor calibration value, initialize the rotation angle sensor, and calibrate the torque sensor zero point if any of the following has occurred:

·

The power steering ECU has been replaced.

·

The power steering link has been replaced.

·

Steering effort differs between left and right.



a.

Inspection before calibration

i.
B135940E01
0.425,2.845 1.557,3.021 1.132,0.177 10 Intelligent Tester 0.6,2.589 0.6,2.832 false 1.48,2.058 1.864,2.214 0.385,0.156 10 DLC3 1.717,2.051 1.841,1.732 false

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch on (IG).


iii.

Turn the intelligent tester on.


iv.

Select "IG Power Supply" from the Data List.


v.

Check the IG power supply voltage on the tester screen.

Power steering ECU
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG Power Supply ECU power source voltage / Min.: 0 V, Max.: 36 V 10 to 14 V Ignition switch on (IG)

Standard voltage:

10 to 14 V


NOTICE:

If the IG power supply voltage is 9 V or less, calibration cannot be performed. In this case, charge or replace the battery, and then perform calibration.




b.

Rotation angle sensor calibration value clear, rotation angle sensor initialization, and torque sensor zero point calibration.

NOTICE:
·

If DTC C1516 (Torque Sensor Zero Point Adjustment Incomplete) is stored, the torque sensor zero point cannot be calibrated. Clear the DTC before starting calibration.

·

If DTC C1526 (Rotation Angle Sensor Initialization Incomplete) is stored, the rotation angle sensor cannot be initialized. Clear the DTC before starting initialization.



i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch on (IG).


iii.

Turn the intelligent tester on.


iv.

Select "Utility".


v.

Selected "Torque Sensor Adjustment".

NOTICE:
·

Set the steering wheel to the center point and align the front tires straight ahead.

·

Do not turn the steering wheel sharply.

·

Do not touch the steering wheel during the torque sensor zero point calibration (for 3 seconds).