Home › Steering › POWER STEERING › STEERING GEAR
RM24M0E _55 Steering _059561 POWER STEERING _0291897 STEERING GEAR A

POWER STEERING  STEERING GEAR  REASSEMBLY  


PROCEDURE

Hide 45536 1.INSTALL NO. 2 STEERING RACK BOOT

a.
C057755

Apply lithium soap base glycol grease to the inside of the small opening of a new No. 2 steering rack boot.


b.

Install the No. 2 steering rack boot to the groove on the rack housing.

NOTICE:
·

Be careful not to damage or twist the boot.

·

Make sure that the boot is free of rust and foreign matter.




Hide 45535 2.INSTALL NO. 1 STEERING RACK BOOT

HINT:

Perform the same procedure as for the No. 2 steering rack boot.


Hide 45536A 3.INSTALL NO. 2 STEERING RACK BOOT CLAMP

a.
U186221E01
2.598,1.974 2.828,2.135 0.230,0.161 10 20° 1.574,0.642 1.894,0.803 0.319,0.161 10 220° 1.618,0.27 1.811,0.436 0.193,0.166 10 *a

Install a new No. 2 steering rack boot clamp to the No. 2 steering rack boot, making sure that the crimped part of the clamp is in the range shown in the illustration.

Text in Illustration
*a Upward
V100136

Front of the Vehicle


b.
F040556E34
1.938,0.875 1.479,0.354 1.479,0.354 1.115,0.354 false 0.76,0.25 1.063,0.396 0.302,0.146 10 false SST

Using SST, tighten the No. 2 steering rack boot clamp as shown in the illustration.

SST
09521-24010  

Clearance:

3.0 mm (0.118 in.) or less


NOTICE:

Be careful not to damage or twist the boot.



Hide 45535D 4.INSTALL NO. 1 STEERING RACK BOOT CLAMP

HINT:

Perform the same procedure as for the No. 2 steering rack boot clamp.


SST
09521-24010  

Hide 45535B 5.INSTALL STEERING RACK BOOT CLIP (for LH Side)

a.
U189505E01
2.216,0.605 2.450,0.767 0.234,0.162 10 76° 1.172,0.084 1.491,0.246 0.319,0.162 10 180° 1.633,0.033 1.817,0.209 0.184,0.176 10 *a

Using pliers, install the steering rack boot clip to the No. 2 steering rack boot making sure that the tabs of the clip are within the range shown in the illustration.

Text in Illustration
*a Upward
V100136

Front of the Vehicle


Hide 45535B 6.INSTALL STEERING RACK BOOT CLIP (for RH Side)

HINT:

Perform the same procedure as for the LH side.


Hide 45510 7.INSPECT STEERING GEAR ASSEMBLY

a.
C213399E01
1.672,0.357 1.967,0.521 0.295,0.164 10 SST 2.433,0.69 2.182,0.439 2.182,0.439 2.021,0.439 false

Using SST, rotate the pinion shaft to see if both the left and the right steering rack boots expand and contract smoothly.

SST
09616-00011  

HINT:

If the operation cannot be done as specified, use a new steering rack boot clamp and reinstall the steering rack boots.



Hide 45407 8.INSTALL TIE ROD END SUB-ASSEMBLY LH

a.
C365104E02
0.573,1.74 1.302,1.927 0.729,0.188 10 false Matchmark

Install the lock nut and the tie rod assembly to the rack end until the matchmarks are aligned.

HINT:

After adjusting the toe-in, tighten the lock nut.



Hide 45046 9.INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.