Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  Source Voltage Drop  


DESCRIPTION

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the center airbag sensor in case the source voltage drops.

When the source voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to a normal working level.

A malfunction in this circuit is displayed differently from other codes, in the fact that no DTCs are recorded. With a normal system code present, the source voltage drop is indicated when the SRS warning light comes on.

A malfunction in this circuit is not recorded in the center airbag sensor.

The SRS warning light automatically goes off when the source voltage returns to normal.

WIRING DIAGRAM

U189020E02
6.927,0 7.146,0 false 5.656,4.365 6.938,4.844 1.281,0.479 10 false G19 5.896,1.542 6.25,1.708 0.354,0.167 10 false IG2 5.625,1.458 5.844,1.625 0.219,0.167 10 false 21 5.625,2.917 5.844,3.083 0.219,0.167 10 false 25 5.625,3.49 5.844,3.656 0.219,0.167 10 false 26 5.885,3.031 6.24,3.198 0.354,0.167 10 false E1 5.885,3.604 6.24,3.771 0.354,0.167 10 false E2 3.833,1.375 4.146,1.594 0.313,0.219 10 false IGN 0.698,1.531 1.573,1.771 0.875,0.24 10 false from Battery 5.656,4.542 7.031,4.823 1.375,0.281 10 false Center Airbag Sensor

PROCEDURE

1.CHECK WIRE HARNESS (CENTER AIRBAG SENSOR - BATTERY)
U186438E03
2.406,1.229 2.76,1.229 true 0.417,0.917 0.771,1.115 0.354,0.198 10 false G19 2.792,1.156 3.104,1.354 0.313,0.198 10 false IG2 0.083,0.073 1.563,0.281 1.479,0.208 10 false Wire Harness Side:

a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect the G19 sensor connector.


d.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


e.

Turn the ignition switch on (IG).


f.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
G19-21 (IG2) - Body ground 11 to 14 V




OK

2.CHECK WIRE HARNESS (CENTER AIRBAG SENSOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK WIRE HARNESS (CENTER AIRBAG SENSOR - BODY GROUND)
U186439E03
1.698,1.26 1.344,1.75 true 1.844,1.26 2.208,1.75 true 0.396,0.896 0.75,1.094 0.354,0.198 10 false G19 1.177,1.74 1.396,1.938 0.219,0.198 10 false E2 2.208,1.74 2.448,1.938 0.24,0.198 10 false E1 0.125,0.073 1.677,0.24 1.552,0.167 10 false Wire Harness Side:

a.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
G19-25 (E1) - Body ground Below 1 Ω
G19-26 (E2) - Body ground




OK

3.CHECK SRS WARNING LIGHT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SRS WARNING LIGHT
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Connect the G19 sensor connector.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch on (IG), and wait for at least 6 seconds.


f.

Operate all components of the electrical system (defogger, wiper, headlight, heater, blower, etc.) and check that SRS warning light does not come on.

OK:

SRS warning light does not come on.




OK

END

NG

REPLACE CENTER AIRBAG SENSOR ASSEMBLY