Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light does not Come ON  


DESCRIPTION

The SRS warning light is located on the combination meter.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to on (IG), and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

When terminals TC and CG of the DLC3 are connected, the DTC is displayed blinking the SRS warning light.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the center airbag sensor in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.

A malfunction in this circuit is not recorded in the center airbag sensor. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the center airbag sensor to the combination meter through the multiplex communication system.

WIRING DIAGRAM

C123566E12
5.698,5.198 6.896,5.396 1.198,0.198 10 false Combination Meter 3.854,5.063 5.208,5.281 1.354,0.219 10 false Center Airbag Sensor 4.104,3.781 4.385,3.927 0.281,0.146 10 false IG2 4.104,4.135 4.385,4.281 0.281,0.146 10 false E1 4.094,4.458 4.375,4.604 0.281,0.146 10 false E2 0.573,1.458 1.823,1.646 1.25,0.188 10 false from ECU-B Fuse 0.708,2.073 1.958,2.26 1.25,0.188 10 false from MET Fuse 5.865,1.479 6.01,1.688 0.146,0.208 10 false B 5.521,1.344 5.729,1.552 0.208,0.208 10 false 22 5.531,1.948 5.74,2.156 0.208,0.208 10 false 21 5.542,2.771 5.75,2.979 0.208,0.208 10 false 33 5.552,3.656 5.76,3.865 0.208,0.208 10 false 32 5.563,4.375 5.771,4.583 0.208,0.208 10 false 31 5.052,3.667 5.26,3.875 0.208,0.208 10 false 13 5.052,4.396 5.26,4.604 0.208,0.208 10 false 22 3.813,3.656 4.021,3.865 0.208,0.208 10 false 21 3.802,4.031 4.01,4.24 0.208,0.208 10 false 25 3.792,4.365 4,4.573 0.208,0.208 10 false 26 5.854,2.073 6.115,2.281 0.26,0.208 10 false IG2 5.865,2.906 6.094,3.115 0.229,0.208 10 false EP 5.854,3.781 6.292,3.99 0.438,0.208 10 false CANH 5.854,4.51 6.292,4.719 0.438,0.208 10 false CANL 4.51,3.781 4.948,3.99 0.438,0.208 10 false CANH 4.552,4.51 4.99,4.719 0.438,0.208 10 false CANL 2,3.781 3.01,3.938 1.01,0.156 10 false from IGN Fuse 3.854,4.896 4.313,5.094 0.458,0.198 10 false G19 5.688,5.021 6.146,5.219 0.458,0.198 10 false G28

PROCEDURE

1.CHECK BATTERY
a.

Measure the voltage of the battery.

Standard voltage:

11 to 14 V




OK

2.CHECK CONNECTION OF CONNECTOR

NG

CHECK AND REPLACE BATTERY OR CHARGING SYSTEM

2.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the combination meter.

OK:

Connectors are properly connected.




OK

3.CHECK WIRE HARNESS (COMBINATION METER - BATTERY AND BODY GROUND)

NG

CONNECT CONNECTOR

3.CHECK WIRE HARNESS (COMBINATION METER - BATTERY AND BODY GROUND)
U186045E02
0.625,1.302 0.625,1.667 false 2.042,1.302 2.125,1.656 false 0.5,1.302 0.333,1.667 false 1.573,0.417 1.896,0.615 0.323,0.198 10 false G28 2.083,1.677 2.344,1.875 0.26,0.198 10 false EP 0.594,1.688 0.76,1.885 0.167,0.198 10 false B 0.135,1.698 0.438,1.896 0.302,0.198 10 false IG2 0.083,0.083 1.542,0.281 1.458,0.198 10 false Wire Harness Side:

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the G28 meter connector.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch on (IG).


f.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
G28-21 (IG2) - Body ground Ignition switch on (IG) 10 to 14 V
G28-22 (B) - Body ground Always



g.

Turn the ignition switch off.


h.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
G28-33 (EP) - Body ground Below 1 Ω




OK

4.CHECK SRS WARNING LIGHT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SRS WARNING LIGHT
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Connect the G28 meter connector.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch on (IG).


f.

Check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds, and then turns on and remains on.


HINT:

The primary check period continues for approximately 6 seconds after the ignition switch is turned on (IG).




OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

NG

Go to METER / GAUGE