Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM D

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  DIAGNOSIS SYSTEM  


CHECK DLC3


a.
H103023E07
1.708,1.875 1.948,1.469 true 1.563,0.917 1.208,0.438 true 1.76,0.927 1.542,0.448 true 1.948,0.927 2.031,0.448 true 2.135,0.927 2.427,0.458 true 2.458,1.896 2.313,1.479 true 1.031,0.25 1.281,0.427 0.25,0.177 10 false CG 1.427,1.906 1.896,2.094 0.469,0.188 10 false CANL 1.396,0.25 1.646,0.427 0.25,0.177 10 false SG 1.813,0.229 2.271,0.396 0.458,0.167 10 false CANH 2.417,0.229 2.677,0.406 0.26,0.177 10 false SIL 2.333,1.917 2.802,2.104 0.469,0.188 10 false BAT

The ECU uses ISO 15765-4 for communication. The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format.

Terminals No. (Symbols) Terminal Description Condition Specified Condition
7 (SIL) - 5 (SG) Bus "+" line During transmission Pulse generation
4 (CG) - Body ground Chassis ground Always Below 1 Ω
5 (SG) - Body ground Signal ground Always Below 1 Ω
16 (BAT) - Body ground Battery positive Always 11 to 14 V
6 (CANH) - 14 (CANL) CAN bus line Engine switch off* 54 to 69 Ω
6 (CANH) - 4 (CG) HIGH-level CAN bus line Engine switch off* 200 Ω or higher
14 (CANL) - 4 (CG) LOW-level CAN bus line Engine switch off* 200 Ω or higher
6 (CANH) - Battery positive HIGH-level CAN bus line Engine switch off* 6 kΩ or higher
14 (CANL) - Battery positive LOW-level CAN bus line Engine switch off* 6 kΩ or higher

NOTICE:

*: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the engine switch, any other switches or the doors.


If the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness and connector.


HINT:

Connect the cable of the intelligent tester to the DLC3, turn the engine switch on (IG) and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.

·

If communication is normal when the tester is connected to another vehicle, inspect the DLC3 on the original vehicle.

·

If communication is still not possible when the tester is connected to another vehicle, the problem is probably in the tester itself. Consult the Service Department listed in the tester's instruction manual.





FUNCTION OF SRS WARNING LIGHT


a.

Primary check

i.

Turn the engine switch off. Wait for at least 2 seconds, then turn the engine switch on (IG). The SRS warning light comes on for approximately 6 seconds and the diagnosis of the airbag system (including the seat belt pretensioners) is performed.

HINT:

If a malfunction is detected during the primary check, the SRS warning light will remain on even after the primary check period of approximately 6 seconds.




b.

Constant check

i.

After the primary check, the center airbag sensor assembly constantly monitors the airbag system for malfunctions.

HINT:

If a malfunction is detected during the constant check, the center airbag sensor assembly functions as follows:

·

The SRS warning light comes on.

·

The SRS warning light turns off, and then comes on. This indicates a source voltage drop. The SRS warning light turns off 10 seconds after the source voltage returns to normal.





c.

Review

i.

When the airbag system is normal:

The SRS warning light comes on only during the primary check period of approximately 6 seconds after the engine switch is turned on (IG).


ii.

When the airbag system is malfunctioning:

·

The SRS warning light remains on even after the primary check period.

·

The SRS warning light turns off after the primary check, but comes on again during the constant check.

·

The SRS warning light does not come on when the engine switch is turned from off to on (IG).


HINT:

The center airbag sensor assembly keeps the SRS warning light on if an airbag or pretensioner has been deployed.





SRS WARNING LIGHT CHECK


a.
C093955

Turn the engine switch on (IG), and check that the SRS warning light comes on for approximately 6 seconds (primary check).


b.

Check that the SRS warning light turns off approximately 6 seconds after the engine switch is turned on (IG) (constant check).

HINT:

When any of the following symptoms occur, refer to Problem Symptoms Table (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PROBLEM SYMPTOMS TABLE).

·

The SRS warning light comes on occasionally after the primary check period.

·

The SRS warning light comes on, but DTCs are not output.

·

The engine switch is turned from off to on (IG), but the SRS warning light does not come on.





FUNCTION OF SRS CONNECTORS


a.

The SRS connectors are located as shown in the illustration.

C358673E02
0.313,0.667 2.635,0.948 2.323,0.281 10 false Center Airbag Sensor Assembly 0.104,0.125 2.552,0.354 2.448,0.229 12 false Connectors of ECU: 0.104,2.5 2.552,2.729 2.448,0.229 12 false Connectors of Sensor Circuit: 0.104,6.323 2.552,6.552 2.448,0.229 12 false Connectors of Squib Circuit: 0.521,1.885 2.229,2.115 1.708,0.229 10 false to SRS Parts and Sensors 0.635,1.042 0.823,1.323 0.188,0.281 10 false 1 1.344,1.042 1.531,1.323 0.188,0.281 10 false 2 1.323,1.24 1.51,1.521 0.188,0.281 10 false A 1.979,1.042 2.167,1.323 0.188,0.281 10 false 3 0.635,1.448 0.823,1.729 0.188,0.281 10 false 4 1.344,1.448 1.531,1.729 0.188,0.281 10 false 5 1.979,1.448 2.167,1.729 0.188,0.281 10 false 6 0.177,4.063 1.177,4.583 1,0.521 10 false to Center Airbag Sensor Assembly 0.177,7.51 1.177,8.094 1,0.583 10 false to Center Airbag Sensor Assembly 2.021,2.969 2.208,3.25 0.188,0.281 10 false 1 2.177,4.521 2.365,4.802 0.188,0.281 10 false 10 2.021,4.521 2.208,4.802 0.188,0.281 10 false 9 2.188,5.052 2.375,5.333 0.188,0.281 10 false 14 1.969,5.052 2.156,5.333 0.188,0.281 10 false 13 3.177,5.052 3.365,5.333 0.188,0.281 10 false 16 2.958,5.052 3.146,5.333 0.188,0.281 10 false 15 3.177,5.583 3.365,5.865 0.188,0.281 10 false 18 2.958,5.583 3.146,5.865 0.188,0.281 10 false 17 3.177,4.521 3.365,4.802 0.188,0.281 10 false 12 2.969,4.521 3.156,4.802 0.188,0.281 10 false 11 2.229,2.969 2.417,3.25 0.188,0.281 10 false 2 3,2.969 3.188,3.25 0.188,0.281 10 false 3 3.208,2.969 3.396,3.25 0.188,0.281 10 false 4 3,3.5 3.188,3.781 0.188,0.281 10 false 5 3.208,3.5 3.396,3.781 0.188,0.281 10 false 6 3,4.01 3.188,4.292 0.188,0.281 10 false 7 3.208,4 3.396,4.281 0.188,0.281 10 false 8 3.448,2.896 5.49,3.156 2.042,0.26 10 false Front Airbag Sensor LH/RH 3.448,3.448 6.885,3.938 3.438,0.49 10 false Side Airbag Sensor LH/RH (for Front Side) 3.448,4.448 6.833,5 3.385,0.552 10 false Side Airbag Sensor LH/RH (for Rear Side) 3.448,4.99 5.448,5.281 2,0.292 10 false Center Floor Airbag Sensor 3.448,5.51 5.448,5.802 2,0.292 10 false Rear Floor Airbag Sensor 2.458,6.844 4.281,7.135 1.823,0.292 10 false Spiral Cable Sub-assembly 3.458,7.375 5.646,7.667 2.188,0.292 10 false Front Passenger Airbag Assembly 3.458,7.906 6.198,8.198 2.74,0.292 10 false Front Seat Side Airbag Assembly LH/RH 3.469,8.438 6.208,8.729 2.74,0.292 10 false Other SRS Parts* 5.281,6.844 6.896,7.208 1.615,0.365 10 false Steering Pad Assembly 3.448,3.958 5.24,4.25 1.792,0.292 10 false Rear Airbag Sensor LH/RH 2.229,6.875 2.417,7.156 0.188,0.281 10 false 2 2.01,6.875 2.198,7.156 0.188,0.281 10 false 1 2.229,7.438 2.417,7.719 0.188,0.281 10 false 6 2.01,7.438 2.198,7.719 0.188,0.281 10 false 5 3.219,7.438 3.406,7.719 0.188,0.281 10 false 8 3,7.438 3.188,7.719 0.188,0.281 10 false 7 2.188,7.969 2.375,8.25 0.188,0.281 10 false 10 2.01,7.979 2.198,8.26 0.188,0.281 10 false 9 3.177,7.969 3.396,8.25 0.219,0.281 10 false 12 2.969,7.969 3.156,8.25 0.188,0.281 10 false 11 3.177,8.5 3.396,8.781 0.219,0.281 10 false 14 2.958,8.51 3.146,8.792 0.188,0.281 10 false 13 5.063,6.906 5.25,7.188 0.188,0.281 10 false 4 4.844,6.906 5.031,7.188 0.188,0.281 10 false 3 0.177,8.927 5.104,9.281 4.927,0.354 10 false *: Curtain Shield Airbag Assembly LH/RH, Driver Side Knee Airbag Assembly, Front Seat Outer Belt Assembly LH/RH

Connector Type Application
ECU Sensor Circuit Squib Circuit
Terminal Twin-Lock Mechanism Connectors 4, 5, 6 Connectors 1, 2 Connectors 1, 5, 6
Half Connection Prevention Mechanism - Connectors 2, 10, 13, 15, 17 Connectors 1, 5, 9, 11
Activation Prevention Mechanism Connectors 4, 5, 6 - Connectors 2, 4, 6, 8, 10, 12, 14
Connector Lock Mechanism (1) - - Connectors 3, 7, 13
Connector Position Assurance Mechanism - Connectors 3, 5, 7, 11 -
Connector Lock Mechanism (2) Connector A - -
Improper Connection Prevention Lock Mechanism Connector A - -


b.

Terminal twin-lock mechanism

C190972E42
0.651,0.02 2.002,0.194 1.350,0.174 10 Lance (Primary Lock) 1.231,1.444 2.164,1.619 0.934,0.174 10 Primary Lock 3.944,0.024 5.618,0.199 1.674,0.174 10 Spacer (Secondary Lock) 4.892,1.43 5.946,1.605 1.054,0.174 10 Secondary Lock 2.435,0.092 2.057,0.095 false 2.821,0.622 2.435,0.092 false 5.712,0.092 5.569,0.095 false 5.821,0.608 5.712,0.092 false

i.

This mechanism is designed to increase the ability of the terminal to remain connected and prevent it from accidentally being disconnected.


ii.

The connector has a two-piece construction consisting of the housing and spacer to securely lock the terminal using both the lance (primary lock) and spacer (secondary lock).



c.

Half connection prevention mechanism

C147461E77
1.542,1.417 1.448,1.083 1.448,1.083 1.302,1.083 false 1.833,1.375 1.667,0.823 1.667,0.823 1.521,0.823 false 2.375,1.323 2.094,0.542 2.094,0.542 1.948,0.542 false 2.99,1.198 3.208,0.573 3.208,0.573 3.375,0.573 false 3.281,1.302 3.458,0.875 3.458,0.875 3.615,0.875 false 6.083,1.146 5.885,0.74 5.885,0.74 5.708,0.74 false 1.146,0.458 1.979,0.625 0.833,0.167 10 false Locking Arm 1.01,0.74 1.552,0.906 0.542,0.167 10 false Stopper 0.51,1 1.344,1.177 0.833,0.177 10 false Locking Part 3.427,0.5 3.865,0.688 0.438,0.188 10 false Slider 3.656,0.802 4.125,0.99 0.469,0.188 10 false Spring 5.198,0.646 5.781,0.833 0.583,0.188 10 false Stopper 4.646,1.948 5.979,2.135 1.333,0.188 10 false Rebounded by Slider

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

If the connector is not completely connected, the connector is disconnected due to the spring force so that no continuity exists.



d.

Activation prevention mechanism

C238382E18
1.594,1.073 1.208,0.927 false 5.26,1.521 5.26,2.042 true 1.844,1.667 1.844,2.083 false 1.656,1.458 1.198,1.458 true 2.646,1.646 2.969,1.646 true 2.354,1.396 3,0.979 3,0.979 2.552,1.469 true 1.771,0.375 2.542,0.542 0.771,0.167 10 false When open 0.323,0.823 1.229,1.01 0.906,0.188 10 false Male Housing 3.042,0.885 4.125,1.042 1.083,0.156 10 false Female Terminal 0.302,1.375 1.219,1.542 0.917,0.167 10 false Male Terminal 3.01,1.573 4.073,1.76 1.063,0.188 10 false Female Housing 1.26,2.104 2.427,2.271 1.167,0.167 10 false Short Spring Plate 5.448,0.375 6.365,0.542 0.917,0.167 10 false When shorted 4.375,2.063 6.167,2.385 1.792,0.323 10 false Short spring plate contacting the male terminal

i.

The activation prevention mechanism is designed to create a short circuit automatically between the positive and negative terminals of an airbag power source connector when disconnected.


ii.

The short spring plate contained in the connector creates a closed circuit on the airbag side (no potential difference can occur between both terminals), preventing accidental airbag deployment when servicing.



e.

Connector lock mechanism (1)

C147462E70
2.521,0.344 2.021,0.198 false 2.635,0.76 2.281,0.885 false 2.469,1.24 2.271,1.323 false 4.927,0.896 5.24,0.688 false 0.531,0.115 2.01,0.292 1.479,0.177 10 Lock the locking button 1.927,0.813 2.302,0.979 0.375,0.167 10 Claw 1.792,1.25 2.281,1.417 0.49,0.167 10 Groove 5.281,0.604 6.927,1.031 1.646,0.427 10 Claw on the locking button is locked in the groove

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Locking the connector lock button engages the locking button claw to the groove on the other side connector to connect the connector securely.



f.

Connector Position Assurance (CPA) mechanism

C161464E53
1.058,0.13 2.269,0.299 1.211,0.170 10 Female Connector 1.261,0.41 2.097,0.580 0.836,0.170 10 Locking Part 1.003,2.219 2.062,2.396 1.059,0.177 10 Male Connector 2.963,0.298 4.550,0.454 1.586,0.156 10 Primary Lock Completed 5.072,0.298 6.839,0.454 1.767,0.156 10 Secondary Lock Completed 4.898,0.699 5.526,0.875 0.628,0.177 10 Retainer 0.858,0.198 1.016,0.2 false 0.837,1.105 0.858,0.198 false 1.051,0.478 1.217,0.478 false 0.933,1.2 1.051,0.478 false 0.727,2.289 0.958,2.289 false 0.511,1.797 0.727,2.289 false 5.63,0.779 5.464,0.779 false 5.66,1.096 5.63,0.779 false

i.

This mechanism is designed to detect when the connector is connected only halfway.


ii.

The CPA and female connector slide to the male connector side at the same time and the primary lock is completed when the female connector is engaged with the male connector. From this point, only the CPA slides to the male connector side and secondary lock is completed when the CPA retainer is engaged with the female connector. When the CPA and female connector ends are aligned, they are completely engaged.



g.

Connector lock mechanism (2)

C364462E02
0.865,1.958 1.031,1.958 1.031,1.958 1.208,1.521 false 4.448,1.51 4.688,1.75 4.688,1.75 4.865,1.75 false 2.51,3.573 2.344,3.573 2.344,3.573 1.875,3.156 false 3.813,3.115 4.01,3.115 4.01,3.115 4.188,2.813 false 5.917,2.708 5.979,2.427 5.979,2.427 6.073,2.427 false 5.563,2.635 5.688,2.635 5.688,2.635 5.813,2.802 false 4.875,3.396 5.104,3.396 5.104,3.396 5.573,3.323 false 0.427,1.865 1.198,2.063 0.771,0.198 10 false Lance 2.563,3.49 3.333,3.688 0.771,0.198 10 false Retainer 4.917,1.677 5.688,1.875 0.771,0.198 10 false Holder 5.094,2.542 5.865,2.74 0.771,0.198 10 false Holder 3.25,3.021 4.021,3.219 0.771,0.198 10 false Retainer 6.125,2.344 6.896,2.542 0.771,0.198 10 false Claw 4.302,3.302 5.073,3.5 0.771,0.198 10 false Retainer

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Sliding the connector all the way into the holder and locking the lance completes the primary lock.


iii.

Engaging the retainer to the holder as shown in the illustration completes the secondary lock, preventing the connector from accidentally being disconnected.



h.

Improper connection prevention lock mechanism

C265081E08
5.292,0.792 5.292,0.219 5.292,0.219 5.656,0.219 false 5.302,1.146 5.302,1.854 5.302,1.854 4.615,1.854 true 4.958,2.979 4.573,2.979 true 1.26,1.073 1.24,0.323 1.24,0.323 1.552,0.323 true 5.99,0.719 5.99,1.031 5.99,1.031 5.51,1.031 true 1.229,1.354 1.229,2.531 1.229,2.531 0.958,2.531 true 3.948,0.073 4.594,0.344 0.646,0.271 10 false Top View 0.271,2.448 1.021,2.74 0.75,0.292 10 false Unlock Rib 3.938,1.76 4.625,2.292 0.688,0.531 10 false Temporary Hold Lock 4.229,2.896 4.656,3.146 0.427,0.25 10 false Lever 5.698,0.146 6.521,0.385 0.823,0.24 10 false Unlock Rib 1.594,0.25 1.854,0.5 0.26,0.25 10 false A 5.948,0.552 6.146,0.729 0.198,0.177 10 false A

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

When the holder is connected to the center airbag sensor assembly, the unlock rib unlocks the temporary hold lock, allowing the lever to be pushed in by rotating around the axis A.


iii.

Locking the lever to the holder locks the holder securely.




ACTIVATION PREVENTION MECHANISM


a.

Function of activation prevention mechanism

i.

An activation prevention mechanism is built into the connector of the airbag system squib circuit to prevent accidental airbag and pretensioner deployment.


ii.

This mechanism closes the circuit when the connector is disconnected by bringing the short spring into contact with the terminals and insulating the circuit from external power sources to prevent accidental airbag and pretensioner deployment.



b.

Releasing of activation prevention mechanism

i.

To release the activation prevention mechanism, insert a piece of paper with the same thickness as the male terminal (approximately 0.5 mm (0.0197 in.)) between the terminals and short spring to break the connection.


ii.

Refer to the following illustrations concerning connectors utilizing the activation prevention mechanism and its release method.

CAUTION:

Never release the activation prevention mechanism on the squib connector even when inspecting with the squib disconnected.


NOTICE:
·

Do not release the activation prevention mechanism unless specified by the troubleshooting procedure.

·

To prevent the terminals and short spring from being damaged, always use a piece of paper with the same thickness as the male terminal.



C243814E05
2.802,2.688 3.177,2.156 3.177,2.156 2.781,2.375 false 2.188,2.781 1.771,3.219 1.771,3.219 2.188,2.458 true 5.177,2.479 4.74,3.208 4.74,3.208 5.198,2.792 true 5.625,2.677 6.094,2.125 6.094,2.125 5.646,2.375 false 6.219,4.563 6.292,4.198 6.292,4.198 6.354,4.198 false 4.021,4.563 4.146,4.177 4.146,4.177 4.219,4.177 false 5.396,4.51 5.396,5.26 false 3.271,4.521 3.271,5.26 false 3.948,6.469 3.865,6.469 3.865,6.469 3.74,6.813 false 3.875,8.083 3.792,8.083 3.792,8.083 3.708,8.448 false 6.521,6.469 6.427,6.469 6.427,6.469 6.313,6.813 false 6.198,8.438 6.198,7.969 6.198,7.969 6.281,7.969 false 3.01,6.865 3.01,7.26 false 5.542,6.875 5.542,7.25 false 3.063,8.469 3.063,8.938 false 5.521,8.448 5.521,8.938 false 0.167,0.021 4,0.198 3.833,0.177 10 false Wire harness connector (to Center Airbag Sensor Assembly): 1.542,1.781 2.563,1.99 1.021,0.208 10 false Before Release 4.708,1.792 5.635,2 0.927,0.208 10 false After Release 3.229,2.115 3.677,2.333 0.448,0.219 10 false Paper 6.146,2.052 6.552,2.219 0.406,0.167 10 false Paper 1.198,3.26 2.469,3.417 1.271,0.156 10 false Short Spring 4.229,3.25 5.521,3.417 1.292,0.167 10 false Short Spring 2.979,3.885 3.958,4.094 0.979,0.208 10 false Before Release 2.563,6.083 3.594,6.302 1.031,0.219 10 false Before Release 5.115,3.875 6.063,4.094 0.948,0.219 10 false After Release 5.208,6.063 6.083,6.26 0.875,0.198 10 false After Release 3.979,6.406 4.396,6.573 0.417,0.167 10 false Paper 4.271,4.104 4.677,4.26 0.406,0.156 10 false Paper 6.385,4.135 6.844,4.344 0.458,0.208 10 false Paper 2.646,7.833 3.615,8.021 0.969,0.188 10 false Before Release 5.052,7.813 5.927,8.042 0.875,0.229 10 false After Release 3.906,8.01 4.333,8.167 0.427,0.156 10 false Paper 6.302,7.896 6.74,8.104 0.438,0.208 10 false Paper 2.781,5.292 4.104,5.5 1.323,0.208 10 false Short Spring 4.865,5.281 6.156,5.49 1.292,0.208 10 false Short Spring 6.552,6.396 6.802,6.563 0.25,0.167 10 false Paper 0.167,3.552 2.625,3.75 2.458,0.198 10 false Spiral Cable Sub-assembly Connector: 0.167,5.667 3.438,5.844 3.271,0.177 10 false Instrument Panel Wire Sub-assembly Connector: 0.167,7.615 2.094,7.844 1.927,0.229 10 false Front Seat Wire Connector: 1.094,0.427 2.667,0.625 1.573,0.198 10 false Instrument Panel Wire 5.031,0.406 6.198,0.583 1.167,0.177 10 false No. 2 Floor Wire 3.542,0.406 4.417,0.583 0.875,0.177 10 false Floor Wire 0.563,9.417 2.198,9.656 1.635,0.24 10 false : Short Spring 2.646,7.281 3.969,7.49 1.323,0.208 10 false Short Spring 5.208,7.281 6.531,7.49 1.323,0.208 10 false Short Spring 2.635,8.969 3.958,9.177 1.323,0.208 10 false Short Spring 5.188,9.031 6.51,9.24 1.323,0.208 10 false Short Spring