CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK LH)
Disconnect the G59, 4A and 4P ECU connectors.
Measure the voltage and resistance of the wire harness side connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| BATB (4P-9) - Body ground | BE - Body ground | Battery power supply | Always | 11 to 14 V |
| ACC (4A-26) - Body ground | GR - Body ground | ACC power supply | Engine switch on (ACC) | 11 to 14 V |
| ACC (4A-26) - Body ground | GR - Body ground | ACC power supply | Engine switch off | Below 1 V |
| GND2 (4A-3) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| GND1 (G59-1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the G59, 4A and 4P ECU connectors.
Measure the voltage of the connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| DCTY (G57-24) - Body ground | L - Body ground | Driver side door courtesy switch input | Driver side door closed | 11 to 14 V |
| DCTY (G57-24) - Body ground | L - Body ground | Driver side door courtesy switch input | Driver side door open | Below 1 V |
| PCTY (G58-21) - Body ground | L - Body ground | Front passenger side door courtesy switch input | Front passenger side door closed | 11 to 14 V |
| PCTY (G58-21) - Body ground | L - Body ground | Front passenger side door courtesy switch input | Front passenger side door open | Below 1 V |
| LCTY (4A-4) - Body ground | BE - Body ground | Slide door LH courtesy light switch input | Slide door LH closed | 11 to 14 V |
| LCTY (4A-4) - Body ground | BE - Body ground | Slide door LH courtesy light switch input | Slide door LH open | Below 1 V |
| RCTY (G58-7) - Body ground | LG - Body ground | Slide door RH courtesy light switch input | Slide door RH closed | 11 to 14 V |
| RCTY (G58-7) - Body ground | LG - Body ground | Slide door RH courtesy light switch input | Slide door RH open | Below 1 V |
| BCTY (G58-25) - Body ground | W - Body ground | Back door courtesy light switch input | Back door closed | 11 to 14 V |
| BCTY (G58-25) - Body ground | W - Body ground | Back door courtesy light switch input | Back door open | Below 1 V |
| ACT+ (4D-5) - Body ground*1 | SB - Body ground | Driver side door lock motor LOCK drive output | Master switch (door control switch) or driver side door key cylinder LOCK | 11 to 14 V |
| ACT+ (4D-5) - Body ground*1 | SB - Body ground | Driver side door lock motor LOCK drive output | Master switch (door control switch) or driver side door key cylinder OFF | Below 1 V |
| ACT+ (4D-1) - Body ground*2 | R - Body ground | Driver side door lock motor LOCK drive output | Master switch (door control switch) or driver side door key cylinder LOCK | 11 to 14 V |
| ACT+ (4D-1) - Body ground*2 | R - Body ground | Driver side door lock motor LOCK drive output | Master switch (door control switch) or driver side door key cylinder OFF | Below 1 V |
| ACT- (4D-21) - Body ground*1 | W - Body ground | Driver side door lock motor UNLOCK drive output | Master switch (door control switch) or driver side door key cylinder UNLOCK | 11 to 14 V |
| ACT- (4D-21) - Body ground*1 | W - Body ground | Driver side door lock motor UNLOCK drive output | Master switch (door control switch) or driver side door key cylinder OFF | Below 1 V |
| ACT- (4D-20) - Body ground*2 | BE - Body ground | Driver side door lock motor UNLOCK drive output | Master switch (door control switch) or driver side door key cylinder UNLOCK | 11 to 14 V |
| ACT- (4D-20) - Body ground*2 | BE - Body ground | Driver side door lock motor UNLOCK drive output | Master switch (door control switch) or driver side door key cylinder OFF | Below 1 V |
| ACT+ (4D-1) - Body ground*1 | R - Body ground | Front passenger side door lock motor LOCK drive output | Master switch (door control switch) or driver side door key cylinder LOCK | 11 to 14 V |
| ACT+ (4D-1) - Body ground*1 | R - Body ground | Front passenger side door lock motor LOCK drive output | Master switch (door control switch) or driver side door key cylinder OFF | Below 1 V |
| ACT+ (4D-5) - Body ground*2 | SB - Body ground | Front passenger side door lock motor LOCK drive output | Master switch (door control switch) or driver side door key cylinder LOCK | 11 to 14 V |
| ACT+ (4D-5) - Body ground*2 | SB - Body ground | Front passenger side door lock motor LOCK drive output | Master switch (door control switch) or driver side door key cylinder OFF | Below 1 V |
| ACT- (4D-20) - Body ground*1 | BE - Body ground | Front passenger side door lock motor UNLOCK drive output | Master switch (door control switch) or driver side door key cylinder UNLOCK | 11 to 14 V |
| ACT- (4D-20) - Body ground*1 | BE - Body ground | Front passenger side door lock motor UNLOCK drive output | Master switch (door control switch) or driver side door key cylinder OFF | Below 1 V |
| ACT- (4D-21) - Body ground*2 | W - Body ground | Front passenger side door lock motor UNLOCK drive output | Master switch (door control switch) or driver side door key cylinder UNLOCK | 11 to 14 V |
| ACT- (4D-21) - Body ground*2 | W - Body ground | Front passenger side door lock motor UNLOCK drive output | Master switch (door control switch) or driver side door key cylinder OFF | Below 1 V |
| ACT+ (4G-7) - Body ground | Y - Body ground | Slide door LH lock motor LOCK drive output | Master switch (door control switch) or driver side door key cylinder LOCK | 11 to 14 V |
| ACT+ (4G-7) - Body ground | Y - Body ground | Slide door LH lock motor LOCK drive output | Master switch (door control switch) or driver side door key cylinder OFF | Below 1 V |
| ACT- (4G-23) - Body ground | L - Body ground | Slide door LH lock motor UNLOCK drive output | Master switch (door control switch) or driver side door key cylinder UNLOCK | 11 to 14 V |
| ACT- (4G-23) - Body ground | L - Body ground | Slide door LH lock motor UNLOCK drive output | Master switch (door control switch) or driver side door key cylinder OFF | Below 1 V |
| ACT+ (4D-4) - Body ground | GR - Body ground | Slide door RH lock motor LOCK drive output | Master switch (door control switch) or driver side door key cylinder LOCK | 11 to 14 V |
| ACT+ (4D-4) - Body ground | GR - Body ground | Slide door RH lock motor LOCK drive output | Master switch (door control switch) or driver side door key cylinder OFF | Below 1 V |
| ACT- (4D-21) - Body ground | W - Body ground | Slide door RH lock motor UNLOCK drive output | Master switch (door control switch) or driver side door key cylinder UNLOCK | 11 to 14 V |
| ACT- (4D-21) - Body ground | W - Body ground | Slide door RH lock motor UNLOCK drive output | Master switch (door control switch) or driver side door key cylinder OFF | Below 1 V |
| LSWD (G57-9) - Body ground | SB - Body ground | Driver side door lock position switch input | Driver side door LOCK | 11 to 14 V |
| LSWD (G57-9) - Body ground | SB - Body ground | Driver side door lock position switch input | Driver side door UNLOCK | Below 1 V |
| LSWL (4D-6) - Body ground | SB - Body ground | Slide door LH lock position switch input | Slide door LH LOCK | Pulse generation |
| LSWL (4D-6) - Body ground | SB - Body ground | Slide door LH lock position switch input | Slide door LH UNLOCK | Below 1 V |
| LSWR (G58-5) - Body ground | Y - Body ground | Slide door RH lock position switch input | Slide door RH LOCK | 11 to 14 V |
| LSWR (G58-5) - Body ground | Y - Body ground | Slide door RH lock position switch input | Slide door RH UNLOCK | Below 1 V |
| TAIL (G57-23) - Body ground | G - Body ground | TAIL signal | Headlight dimmer switch position OFF | Pulse generation |
| TAIL (G57-23) - Body ground | G - Body ground | TAIL signal | Headlight dimmer switch position TAIL | Below 1 V |
| HEAD (G58-17) - Body ground | V - Body ground | HEAD signal | Headlight dimmer switch position OFF | 11 to 14 V |
| HEAD (G58-17) - Body ground | V - Body ground | HEAD signal | Headlight dimmer switch position HEAD | Below 1 V |
| HRLY (4L-6) - Body ground | R - Body ground | HEAD signal | Headlight dimmer switch position OFF | 11 to 14 V |
| HRLY (4L-6) - Body ground | R - Body ground | HEAD signal | Headlight dimmer switch position HEAD | Below 1 V |
| DIM (4P-8) - Body ground | W - Body ground | High beam signal | Headlight dimmer switch position OFF | 11 to 14 V |
| DIM (4P-8) - Body ground | W - Body ground | High beam signal | Headlight dimmer switch position HEAD and BEAM | Below 1 V |
| HU (4D-10) - Body ground | P - Body ground | High beam signal | Headlight dimmer switch position OFF | Pulse generation |
| HU (4D-10) - Body ground | P - Body ground | High beam signal | Headlight dimmer switch position HEAD and BEAM | Below 1 V |
| A (G57-21) - Body ground | V - Body ground | AUTO signal | Headlight dimmer switch position OFF | 11 to 14 V |
| A (G57-21) - Body ground | V - Body ground | AUTO signal | Headlight dimmer switch position AUTO | Below 1 V |
| HF (G57-13) - Body ground | Y - Body ground | FLASH (Passing) signal | Headlight dimmer switch position OFF | 11 to 14 V |
| HF (G57-13) - Body ground | Y - Body ground | FLASH (Passing) signal | Headlight dimmer switch position FLASH | Below 1 V |
| FFOG (G58-28) - Body ground | LG - Body ground | Front fog light signal | Headlight dimmer switch position TAIL or HEAD, front fog light switch OFF | 11 to 14 V |
| FFOG (G58-28) - Body ground | LG - Body ground | Front fog light signal | Headlight dimmer switch position TAIL or HEAD, front fog light switch ON | Below 1 V |
| FFGO (G57-4) - Body ground | LG - Body ground | Front fog light signal | Headlight dimmer switch position TAIL or HEAD, front fog light switch OFF | 11 to 14 V |
| FFGO (G57-4) - Body ground | LG - Body ground | Front fog light signal | Headlight dimmer switch position TAIL or HEAD, front fog light switch ON | Below 1 V |
| RFOG (G58-9) - Body ground | L - Body ground | Rear fog light signal | Headlight dimmer switch position TAIL or HEAD, rear fog light switch OFF | Pulse generation |
| RFOG (G58-9) - Body ground | L - Body ground | Rear fog light signal | Headlight dimmer switch position TAIL or HEAD, rear fog light switch ON | Below 1 V |
| RFGO (G59-14) - Body ground | LG - Body ground | Rear fog light signal | Headlight dimmer switch position TAIL or HEAD, rear fog light switch OFF | 11 to 14 V |
| RFGO (G59-14) - Body ground | LG - Body ground | Rear fog light signal | Headlight dimmer switch position TAIL or HEAD, rear fog light switch ON | Below 1 V |
| FSPT (G59-11) - Body ground | SB - Body ground | Inside handle illumination light signal | Door open | Below 1 V |
| FSPT (G59-11) - Body ground | SB - Body ground | Inside handle illumination light signal | Door closed | Voltage increases gradually |
| ILE (4D-2) - Body ground | Y - Body ground | Illumination signal | Door open | Below 1 V |
| ILE (4D-2) - Body ground | Y - Body ground | Illumination signal | Door closed | 11 to 14 V |
| HAZ (G59-4) - Body ground*1 | GR - Body ground | Hazard switch signal | Hazard switch OFF | 11 to 14 V |
| HAZ (G59-4) - Body ground*1 | GR - Body ground | Hazard switch signal | Hazard switch ON | Below 1 V |
| CLTB (G58-20) - Body ground | GR - Body ground | Automatic light control sensor power supply | Engine switch on (IG) | 11 to 14 V |
| CLTE (G58-18) - Body ground | LG - Body ground | Automatic light control sensor ground | Always | Below 1 V |
| CLTS (G58-19) - Body ground | B - Body ground | Automatic light control sensor signal | Engine switch on (IG), headlight dimmer switch AUTO position | Pulse generation
Waveform varies according to brightness |
*1: for LHD
*2: for RHD
If the result is not as specified, the ECU may have a malfunction.
CHECK TURN SIGNAL FLASHER RELAY (for LHD)
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| IG (G41-1) - Body ground | B - Body ground | Power source (IG) | Engine switch off | Below 1 V |
| IG (G41-1) - Body ground | B - Body ground | Power source (IG) | Engine switch on (IG) | 11 to 14 V |
| B (G41-4) - Body ground | P - Body ground | Battery power supply | Always | 11 to 14 V |
| E (G41-7) - Body ground | W-B - Body ground | Ground | Always | 11 to 14 V |
| EL (G41-5) - Body ground | Y - Body ground | Turn LH signal | Headlight dimmer switch NORMAL position | Below 1 V |
| EL (G41-5) - Body ground | Y - Body ground | Turn LH signal | Headlight dimmer switch TURN LH position | 11 to 14 V |
| LL (G41-3) - Body ground | V - Body ground | Turn LH signal | Headlight dimmer switch NORMAL position | Below 1 V |
| LL (G41-3) - Body ground | V - Body ground | Turn LH signal | Headlight dimmer switch TURN LH position | 11 to 14 V |
| ER (G41-6) - Body ground | G - Body ground | Turn RH signal | Headlight dimmer switch NORMAL position | Below 1 V |
| ER (G41-6) - Body ground | G - Body ground | Turn RH signal | Headlight dimmer switch TURN RH position | 11 to 14 V |
| LR (G41-2) - Body ground | Y - Body ground | Turn RH signal | Headlight dimmer switch NORMAL position | Below 1 V |
| LR (G41-2) - Body ground | Y - Body ground | Turn RH signal | Headlight dimmer switch TURN RH position | 11 to 14 V |
| HAZ (G41-8) - Body ground | GR - Body ground | Hazard switch signal | Hazard switch OFF | Below 1 V |
| HAZ (G41-8) - Body ground | GR - Body ground | Hazard switch signal | Hazard switch ON | 11 to 14 V |
If the result is not as specified, the relay may have a malfunction.
CHECK COMBINATION METER ECU (for RHD)
Measure the voltage according to the value(s) in the table below.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| HAZ (G123-5) - Body ground | GR - Body ground | Hazard warning signal | Engine switch on (IG), hazard warning signal switch OFF | 11 to 14 V |
| HAZ (G123-5) - Body ground | GR - Body ground | Hazard warning signal | Engine switch on (IG), hazard warning signal switch ON | Below 1 V |
| LL (G123-7) - Body ground | V - Body ground | LH turn indicator light signal (Output) | Engine switch on (IG), LH turn indicator light OFF | Below 1 V |
| LL (G123-7) - Body ground | V - Body ground | LH turn indicator light signal (Output) | Engine switch on (IG), LH turn indicator light blinking | Below 1 V ←→ 11 to 14 V |
| ER (G123-9) - Body ground | SB - Body ground | RH turn indicator light signal (Input) | Engine switch on (IG), RH turn signal switch OFF | 11 to 14 V |
| ER (G123-9) - Body ground | SB - Body ground | RH turn indicator light signal (Input) | Engine switch on (IG), RH turn signal switch ON | Below 1 V |
| EL (G123-10) - Body ground | P - Body ground | LH turn indicator light signal (Input) | Engine switch on (IG), LH turn signal switch OFF | 11 to 14 V |
| EL (G123-10) - Body ground | P - Body ground | LH turn indicator light signal (Input) | Engine switch on (IG), LH turn signal switch ON | Below 1 V |
| LR (G123-13) - Body ground | Y - Body ground | RH turn indicator light signal (Output) | Engine switch on (IG), RH turn indicator light OFF | Below 1 V |
| LR (G123-13) - Body ground | Y - Body ground | RH turn indicator light signal (Output) | Engine switch on (IG), RH turn indicator light blinking | Below 1 V ←→ 11 to 14 V |
If the result is not as specified, the ECU may have a malfunction.
CHECK AFS ECU (w/AFS)
Disconnect the A28 ECU connector.
Measure the voltage and resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| IG (A28-15) - Body ground | B - Body ground | Power source (IG) | Engine switch off | Below 1 V |
| IG (A28-15) - Body ground | B - Body ground | Power source (IG) | Engine switch on (IG) | 11 to 14 V |
| IGS (A28-14) - Body ground | B - Body ground | Power source (IG) | Engine switch off | Below 1 V |
| IGS (A28-14) - Body ground | B - Body ground | Power source (IG) | Engine switch on (IG) | 11 to 14 V |
| E1 (A28-22) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, the wire harness may have a malfunction.
Reconnect the A28 ECU connector.
Measure the voltage of the connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| INIT (A28-7) - Body ground | BR - Body ground | AFS operation check | Engine switch on (IG) | 5 V |
| CAN+ (A28-12) - Body ground | B - Body ground | CAN communication | Engine switch on (IG) | Pulse generation |
| CAN- (A28-13) - Body ground | W - Body ground | CAN communication | Engine switch on (IG) | Pulse generation |
| SML (A28-29) - Body ground | G - Body ground | Swivel actuator LH LIN communication | Engine switch on (IG) | Pulse generation |
| SMGL (A28-23) - Body ground | GR - Body ground | Swivel actuator LH ground | Always | Below 1 V |
| SMBL (A28-1) - Body ground | SB - Body ground | Swivel actuator LH power output | Engine switch on (IG) | 11 to 14 V |
| SMR (A28-10) - Body ground | L - Body ground | Swivel actuator RH LIN communication | Engine switch on (IG) | Pulse generation |
| SMGR (A28-24) - Body ground | Y - Body ground | Swivel actuator RH ground | Always | Below 1 V |
| SMBR (A28-2) - Body ground | BE - Body ground | Swivel actuator RH power output | Engine switch on (IG) | 11 to 14 V |
| LL1+ (A28-3) - Body ground | LG - Body ground | Headlight leveling motor LH power output | Engine switch on (IG) | 11 to 14 V |
| LL1- (A28-27) - Body ground | BE - Body ground | Headlight leveling motor LH ground | Always | Below 1 V |
| LHT (A28-30) - Body ground | V -Body ground | Headlight leveling motor LH LIN communication | Engine switch on (IG) | Pulse generation |
| LR1+ (A28-4) - Body ground | R - Body ground | Headlight leveling motor RH power output | Engine switch on (IG) | 11 to 14 V |
| LR1- (A28-28) - Body ground | BR - Body ground | Headlight leveling motor RH ground | Always | Below 1 V |
| RHT (A28-11) - Body ground | W*1 - Body ground
P*2 - Body ground |
Headlight leveling motor RH LIN communication | Engine switch on (IG) | Pulse generation |
| B (A28-18) - Body ground | V - Body ground | Height control sensor power output | Engine switch on (IG) | 5 V |
| SHRL (A28-19) - Body ground | GR - Body ground | Height control sensor signal | Engine switch on (IG)
(No occupants other than driver, vehicle is unloaded, vehicle is stopped) |
2.8 V |
| SGF (A28-21) - Body ground | B - Body ground | Height control sensor ground | Always | Below 1 V |
| MSW (A28-32) - Body ground | Y - Body ground | AFS OFF switch input signal | Engine switch on (IG)
AFS OFF switch ON (cancel) |
Below 1 V |
| MSW (A28-32) - Body ground | Y - Body ground | AFS OFF switch input signal | Engine switch on (IG)
AFS OFF switch OFF (normal) |
11 to 14 V |
*1: LHD 2GR-FE
*2: Except*1
If the result is not as specified, the ECU may have a malfunction.