Home › Vehicle Interior › LIGHTING › LIGHTING SYSTEM(except LED Headlight)
RM24M0E _58 Vehicle Interior _059564 LIGHTING _0291933 LIGHTING SYSTEM(except LED Headlight) C

LIGHTING  LIGHTING SYSTEM(except LED Headlight)  B1244  Light Sensor Circuit Malfunction  


DESCRIPTION

This DTC is output when a failure in the automatic light control sensor circuit is detected.

DTC No. DTC Detection Condition Trouble Area
B1244 Automatic light control sensor malfunction
·

Main body ECU

·

Automatic light control sensor

·

Wire harness



WIRING DIAGRAM

E132264E01
0.211,2.384 2.193,2.554 1.982,0.171 10 H1 0.211,2.571 2.193,2.741 1.982,0.171 10 Automatic Light Control Sensor 1.184,0.653 1.578,0.829 0.394,0.176 10 CLTB 1.674,0.765 2.068,0.941 0.394,0.176 10 6 1.674,1.387 2.068,1.564 0.394,0.176 10 3 1.674,1.984 2.068,2.160 0.394,0.176 10 5 4.468,0.765 4.645,0.941 0.177,0.176 10 20 4.468,1.387 4.645,1.564 0.177,0.176 10 18 4.468,1.984 4.645,2.160 0.177,0.176 10 19 1.182,1.248 1.601,1.409 0.420,0.161 10 CLTE 1.18,1.85 1.573,2.017 0.392,0.167 10 CLTS 4.753,0.653 5.187,0.805 0.434,0.153 10 CLTB 4.753,1.248 5.173,1.413 0.420,0.165 10 CLTE 4.753,1.85 5.145,2.009 0.392,0.159 10 CLTS 5.072,2.538 6.165,2.712 1.093,0.174 10 G58 5.072,2.725 6.165,2.898 1.093,0.174 10 Main Body ECU

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (AUTOMATIC LIGHT CONTROL SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and the tester ON.


c.

Read the Data List according to the prompts displayed on the tester.

Main body ECU
Item Tester Details Normal Condition Diagnostic Note
Illumination Rate Info Automatic light control sensor / Min.: 0, Max.: 99.99 Almost same as sensor sensitivity -

OK:

Tester value changes according to light intensity.




NG

2.CHECK WIRE HARNESS (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)

OK

REPLACE MAIN BODY ECU

2.CHECK WIRE HARNESS (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)
U188733E02
1.594,3.75 0.833,4.104 0.833,4.104 0.833,4.26 false 1.625,3.885 1.625,4.219 false 1.833,3.885 2.406,4.073 2.406,4.073 2.406,4.25 false 2,1.76 1.281,2.25 false 2.146,1.771 2,2.26 false 2.281,1.771 2.677,2.26 false 0.208,0.146 1.521,0.323 1.313,0.177 10 false Wire Harness Side: 1.281,0.708 2.479,0.865 1.198,0.156 10 false Main Body ECU 1,2.292 1.438,2.448 0.438,0.156 10 false CLTE 1.844,2.302 2.281,2.458 0.438,0.156 10 false CLTS 2.583,2.333 3.021,2.49 0.438,0.156 10 false CLTB 0.677,4.292 1.115,4.448 0.438,0.156 10 false CLTE 1.469,4.219 1.906,4.375 0.438,0.156 10 false CLTS 2.167,4.25 2.604,4.406 0.438,0.156 10 false CLTB 0.844,2.844 2.792,3 1.948,0.156 10 false Automatic Light Control Sensor 0.906,3.635 1.104,3.813 0.198,0.177 10 false H1 0.417,1.552 0.698,1.729 0.281,0.177 10 false G58

a.

Disconnect the G58 main body ECU connector.


b.

Disconnect the H1 automatic light control sensor connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G58-18 (CLTE) - H1-3 (CLTE) Below 1 Ω
G58-18 (CLTE) or H1-3 (CLTE) - Body ground 10 kΩ or higher
G58-19 (CLTS) - H1-5 CLTS) Below 1 Ω
G58-19 (CLTS) or H1-5 (CLTS) - Body ground 10 kΩ or higher
G58-20 (CLTB) - H1-6 (CLTB) Below 1 Ω
G58-20 (CLTB) or H1-6 (CLTB) - Body ground 10 kΩ or higher




OK

3.REPLACE AUTOMATIC LIGHT CONTROL SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE AUTOMATIC LIGHT CONTROL SENSOR
a.

Replace the automatic light control sensor with a normally functioning one or a new one.


b.

Check for DTC.

OK:

DTC is not output.




OK

END (AUTOMATIC LIGHT CONTROL SENSOR IS FAULTY)

NG

REPLACE MAIN BODY ECU