Home › Vehicle Interior › LIGHTING › LIGHTING SYSTEM(except LED Headlight)
RM24M0E _58 Vehicle Interior _059564 LIGHTING _0291933 LIGHTING SYSTEM(except LED Headlight) J

LIGHTING  LIGHTING SYSTEM(except LED Headlight)  Headlight Relay Circuit  


DESCRIPTION

When the light control switch, located on the headlight dimmer switch, is turned to the HEAD position, the headlight relay (marking: H-LP) illuminates the headlights.

WIRING DIAGRAM

E132454E04
1.344,3.938 2.031,4.094 0.688,0.156 10 false H-LP LL 0.177,2.74 0.917,3.073 0.74,0.333 10 false from Battery 1.458,2.104 2.146,2.25 0.688,0.146 10 false H-LP RL 2.635,5.688 3.302,6.052 0.667,0.365 10 false Headlight LH (Low) 2.104,5.698 2.375,5.865 0.271,0.167 10 false HID 4.01,5.688 4.354,5.854 0.344,0.167 10 false CPU 4.594,5.688 4.865,5.854 0.271,0.167 10 false HID 1.542,5.698 1.885,5.865 0.344,0.167 10 false CPU 1.042,5.479 1.24,5.646 0.198,0.167 10 false *3 1.771,5.458 1.969,5.625 0.198,0.167 10 false *4 3.51,5.479 3.708,5.646 0.198,0.167 10 false *3 1.073,5.188 1.219,5.354 0.146,0.167 10 false 1 1.063,6.281 1.208,6.448 0.146,0.167 10 false 2 3.552,5.208 3.698,5.375 0.146,0.167 10 false 1 3.531,6.302 3.677,6.469 0.146,0.167 10 false 2 4.24,5.469 4.438,5.635 0.198,0.167 10 false *4 2.635,5.479 2.917,5.646 0.281,0.167 10 false B24 5.104,5.427 5.427,5.594 0.323,0.167 10 false B26 5.094,5.635 5.802,5.99 0.708,0.354 10 false Headlight RH (Low) 0.177,6.406 0.917,6.583 0.74,0.177 10 false *1: for LHD 1.438,1.281 1.927,1.427 0.49,0.146 10 false H-LP 2.906,1.417 3.458,1.771 0.552,0.354 10 false Dimmer Switch 3.844,1.458 5.198,1.635 1.354,0.177 10 false Light Control Switch 2.969,2.208 3.333,2.375 0.365,0.167 10 false LOW 3.542,2.208 4,2.396 0.458,0.188 10 false HEAD 4.135,2.208 4.49,2.396 0.354,0.188 10 false TAIL 4.646,2.208 4.958,2.375 0.313,0.167 10 false OFF 5.406,0.729 5.615,0.896 0.208,0.167 10 false 4L 5.875,4.677 6.083,4.844 0.208,0.167 10 false 17 5.677,3.375 5.99,3.542 0.313,0.167 10 false 20*1 5.677,3.646 5.99,3.813 0.313,0.167 10 false 11*2 2.302,2.458 2.615,2.625 0.313,0.167 10 false 12*1 2.292,2.719 2.604,2.885 0.313,0.167 10 false 19*2 5.833,4.906 6.115,5.073 0.281,0.167 10 false G58 5.406,0.531 5.615,0.698 0.208,0.167 10 false 6 6,0.854 6.115,1.021 0.115,0.167 10 false 8 1.906,0.615 2.021,0.781 0.115,0.167 10 false 1 1.156,0.615 1.271,0.781 0.115,0.167 10 false 2 1.917,1.094 2.031,1.26 0.115,0.167 10 false 3 1.146,1.094 1.26,1.26 0.115,0.167 10 false 5 5.083,2.49 5.313,2.667 0.229,0.177 10 false EL 5.104,2.948 5.26,3.115 0.156,0.167 10 false T 5.115,3.438 5.271,3.615 0.156,0.177 10 false H 5.094,3.885 5.313,4.063 0.219,0.177 10 false HL 5.927,5.365 6.99,5.552 1.063,0.188 10 false Main Body ECU 6.198,0.74 6.729,0.917 0.531,0.177 10 false HRLY 6.177,4.896 6.74,5.083 0.563,0.188 10 false HEAD 3.354,4.729 4.99,4.938 1.635,0.208 10 false Headlight Dimmer Switch 3.333,4.521 3.656,4.677 0.323,0.156 10 false G8 0.177,6.729 0.885,6.896 0.708,0.167 10 false *2: for RHD 0.167,7.042 0.885,7.219 0.719,0.177 10 false *3: w/o HID 0.198,7.365 0.844,7.563 0.646,0.198 10 false *4: w/ HID

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (HEADLIGHT LOW)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and press the intelligent tester main switch ON.


c.

Select the item below in the Active Test and then check that the relay operates.

Main body ECU:
Item Test Details: Display (Range) Diagnostic Note
Head Light Headlight Relay ON/OFF -


OK:

Headlights (LOW) come on




NG

2.INSPECT FUSE (H-LP LL, H-LP RL)

OK

14.INSPECT HEADLIGHT DIMMER SWITCH
2.INSPECT FUSE (H-LP LL, H-LP RL)
a.

Remove the H-LP LL fuse and H-LP RL fuse from the engine room No. 2 relay block.


b.

Measure the resistance of the fuses.

Standard resistance:

Below 1 Ω




OK

3.INSPECT HEADLIGHT RELAY (Marking: H-LP)

NG

REPLACE FUSE

3.INSPECT HEADLIGHT RELAY (Marking: H-LP)
B112776

a.

Remove the headlight relay from the engine room No. 2 relay block.


b.

Measure the resistance of the relay.

Standard resistance:
Tester Connection Specified Condition
3 - 5 10 kΩ or higher
3 - 5 Below 1 Ω
(Battery voltage applied to terminals 1 and 2)




OK

4.CHECK VEHICLE CONDITION

NG

REPLACE HEADLIGHT RELAY

4.CHECK VEHICLE CONDITION
a.

Check the vehicle condition.

Result
Result Proceed to
w/o HID A
w/ HID B



A

5.INSPECT BULB (HEADLIGHT BULB)

B

9.REPLACE HID HEADLIGHT BULB
5.INSPECT BULB (HEADLIGHT BULB)
a.
C128857E02
1.458,1.198 0.844,1.604 false 2.021,1.198 2.615,1.594 false 0.385,1.615 1.354,1.792 0.969,0.177 10 false 2 (Battery +) 2.26,1.615 3.177,1.76 0.917,0.146 10 false 1 (Battery -)

Remove the headlight bulbs (Lo-beam).


b.

Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1. Then check that the bulb illuminates.

OK:

Bulb illuminates.




OK

6.INSPECT HEADLIGHT ASSEMBLY

NG

REPLACE BULB

6.INSPECT HEADLIGHT ASSEMBLY
a.
E118527E02
2.287,0.369 3.049,0.543 0.762,0.174 10 Battery (+) 0.317,0.369 1.037,0.543 0.721,0.174 10 Battery (-) 1.864,1.308 2.23,0.483 false 1.577,1.308 1.211,0.483 false

Remove the headlight.


b.

Connect the positive (+) lead from the battery to terminal 1 and the negative (-) lead to terminal 2. Then check that the bulb illuminates.

OK:

Bulb illuminates.




OK

7.CHECK WIRE HARNESS (MAIN BODY ECU - BATTERY)

NG

REPLACE HEADLIGHT ASSEMBLY

7.CHECK WIRE HARNESS (MAIN BODY ECU - BATTERY)
a.
U185964E01
0.068,0.045 1.391,0.221 1.323,0.176 10 Wire Harness Side: 0.441,1.484 0.844,1.640 0.403,0.156 10 HRLY 1.615,0.516 1.787,0.697 0.171,0.181 10 4L 1.337,1.573 0.939,1.573 false

Disconnect the 4L ECU connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
4L-6 (HRLY) - Body ground 10 to 14 V




OK

8.CHECK MAIN BODY ECU (HRLY VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK MAIN BODY ECU (HRLY VOLTAGE)
U185965E02
1.146,2.115 1.146,1.771 false 1.563,2.385 1.729,2.563 0.167,0.177 10 false 4L 2.188,0.625 3.219,0.781 1.031,0.156 10 false Main Body ECU 0.958,1.594 1.375,1.75 0.417,0.156 10 false HRLY

a.

Measure the voltage of the ECU.

Standard voltage:
Tester Connection Condition Specified Condition
4L-6 (HRLY) - Body ground Light control switch OFF 10 to 14 V
4L-6 (HRLY) - Body ground Light control switch ON (HEAD) Below 1 V




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (HEADLIGHT RELAY - HEADLIGHT AND BODY GROUND)

NG

REPLACE MAIN BODY ECU

9.REPLACE HID HEADLIGHT BULB
a.

Replace the HID headlight bulb with a new one.

CAUTION:

Do not touch the bulb glass with your fingers.



b.

Check that the bulb illuminates normally.

OK:

Bulb illuminates normally.




NG

10.CHECK WIRE HARNESS (MAIN BODY ECU - BATTERY)

OK

END

10.CHECK WIRE HARNESS (MAIN BODY ECU - BATTERY)
a.
U185964E01
0.068,0.045 1.391,0.221 1.323,0.176 10 Wire Harness Side: 0.441,1.484 0.844,1.640 0.403,0.156 10 HRLY 1.615,0.516 1.787,0.697 0.171,0.181 10 4L 1.337,1.573 0.939,1.573 false

Disconnect the 4L ECU connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
4L-6 (HRLY) - Body ground 10 to 14 V




OK

11.CHECK MAIN BODY ECU (HRLY VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK MAIN BODY ECU (HRLY VOLTAGE)
U185965E02
1.146,2.115 1.146,1.771 false 1.563,2.385 1.729,2.563 0.167,0.177 10 false 4L 2.188,0.625 3.219,0.781 1.031,0.156 10 false Main Body ECU 0.958,1.594 1.375,1.75 0.417,0.156 10 false HRLY

a.

Measure the voltage of the ECU.

Standard voltage:
Tester Connection Condition Specified Condition
4L-6 (HRLY) - Body ground Light control switch OFF 10 to 14 V
4L-6 (HRLY) - Body ground Light control switch ON (HEAD) Below 1 V




OK

12.CHECK WIRE HARNESS (HEADLIGHT - HEADLIGHT RELAY AND BODY GROUND)

NG

REPLACE MAIN BODY ECU

12.CHECK WIRE HARNESS (HEADLIGHT - HEADLIGHT RELAY AND BODY GROUND)
a.

Disconnect the B24 and B26 headlight (Lo-beam) connectors.

U188739E02
0.208,0.115 1.521,0.271 1.313,0.156 10 false Wire Harness Side: 3.917,0.698 6,0.854 2.083,0.156 10 false Engine Room No. 2 Relay Block 0.656,1.5 2.042,1.656 1.385,0.156 10 false Headlight (Lo-Beam) 0.167,3.25 0.792,3.406 0.625,0.156 10 false *1: for LH 5.146,3.229 6.135,3.479 0.99,0.25 10 false Headlight Relay 1.156,1.948 1.313,2.125 0.156,0.177 10 false *1 1.156,2.26 1.313,2.438 0.156,0.177 10 false *2 0.146,3.5 0.823,3.656 0.677,0.156 10 false *2: for RH 0.792,1.948 1.115,2.115 0.323,0.167 10 false B24 0.792,2.26 1.115,2.427 0.323,0.167 10 false B26


b.

Remove the headlight relay from the engine room No. 2 relay block.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
B24-1 - Relay block No. 2 headlight relay terminal 3 Below 1 Ω
B24-1 or relay block No. 2 headlight relay terminal 3 - Body ground 10 kΩ or higher
B26-1 - Relay block No. 2 headlight relay terminal 3 Below 1 Ω
B26-1 or relay block No. 2 headlight relay terminal 3 - Body ground 10 kΩ or higher
B24-2 - Body ground Below 1 Ω
B26-2 - Body ground Below 1 Ω




OK

13.REPLACE HEADLIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE HEADLIGHT ASSEMBLY
a.

Replace the headlight assembly with a new one.


b.

Check that the headlight illuminates normally.

OK:

Light illuminates normally.




OK

END

NG

REPLACE MAIN BODY ECU

14.INSPECT HEADLIGHT DIMMER SWITCH
a.

Remove the headlight dimmer switch.


B128006E47
0.938,1.26 0.583,1.646 false 2.479,1.24 2.875,1.302 false 1.292,1.25 1.031,1.719 false 1.625,1.219 1.51,2.031 false 1.792,1.25 2.188,1.719 false 1.115,1.188 0.552,0.51 false 2.115,1.271 2.719,1.656 false 2.271,1.208 2.781,0.417 false 0.354,1.677 0.667,1.896 0.313,0.219 10 false H*1 2.948,1.26 3.26,1.469 0.313,0.208 10 false H*2 2.813,1.646 3.083,1.885 0.271,0.24 10 false T*2 0.865,1.771 1.104,2.01 0.24,0.24 10 false T*1 1.354,2.063 1.781,2.292 0.427,0.229 10 false HL*1 2.021,1.729 2.531,1.958 0.51,0.229 10 false HL*2 0.156,2.823 0.906,2.99 0.75,0.167 10 false *1: for LHD 0.208,0.375 0.594,0.615 0.385,0.24 10 false EL*2 2.833,0.271 3.208,0.5 0.375,0.229 10 false EL*1 0.156,3.083 0.927,3.24 0.771,0.156 10 false *2: for RHD

b.

Measure the resistance of the switch.

Standard resistance:
for LHD
Tester Connection Switch Condition Specified Condition
18 (T) - 12 (EL) Light control switch TAIL Below 1 Ω
18 (T) - 12 (EL) Light control switch OFF 10 kΩ or higher
20 (H) - 12 (EL) Light control switch HEAD Below 1 Ω
20 (H) - 12 (EL) Light control switch OFF 10 kΩ or higher
16 (HL) - 12 (EL) Dimmer switch LOW Below 1 Ω
16 (HL) - 12 (EL) Dimmer switch HIGH 10 kΩ or higher

for RHD
Tester Connection Switch Condition Specified Condition
13 (T) - 19 (EL) Light control switch TAIL Below 1 Ω
13 (T) - 19 (EL) Light control switch OFF 10 kΩ or higher
11 (H) - 19 (EL) Light control switch HEAD Below 1 Ω
11 (H) - 19 (EL) Light control switch OFF 10 kΩ or higher
15 (HL) - 19 (EL) Dimmer switch LOW Below 1 Ω
15 (HL) - 19 (EL) Dimmer switch HIGH 10 kΩ or higher




OK

15.CHECK WIRE HARNESS (DIMMER SWITCH - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY

15.CHECK WIRE HARNESS (DIMMER SWITCH - MAIN BODY ECU AND BODY GROUND)
a.
U188735E02
1.833,1.802 1.74,1.896 1.74,1.896 1.74,2.375 false 1.104,4.01 1.094,4.292 false 1.24,4.021 1.354,4.271 false 2.229,3.969 2.531,3.781 false 2.083,4.021 2.385,4.26 false 0.156,0.104 1.479,0.26 1.323,0.156 10 false Wire Harness Side: 1.135,0.708 2.333,0.865 1.198,0.156 10 false Main Body ECU 0.844,2.979 2.458,3.135 1.615,0.156 10 false Headlight Dimmer Switch 0.094,4.24 0.844,4.396 0.75,0.156 10 false *2: for RHD 0.094,3.979 0.844,4.135 0.75,0.156 10 false *1: for LHD 1.573,2.427 2.01,2.583 0.438,0.156 10 false HEAD 0.563,3.625 0.76,3.802 0.198,0.177 10 false G8 0.51,1.604 0.792,1.781 0.281,0.177 10 false G58 0.979,4.365 1.26,4.521 0.281,0.156 10 false H*2 1.333,4.333 1.688,4.49 0.354,0.156 10 false EL*1 2.406,4.292 2.76,4.448 0.354,0.156 10 false EL*2 2.583,3.708 2.865,3.865 0.281,0.156 10 false H*1

Disconnect the G8 headlight dimmer switch connector.


b.

Disconnect the G58 main body ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
for LHD
Tester Connection Specified Condition
G8-20 (H) - G58-17 (HEAD) Below 1 Ω
G8-20 (H) or G58-17 (HEAD) - Body ground 10 kΩ or higher
G8-12 (EL) - Body ground Below 1 Ω

for RHD
Tester Connection Specified Condition
G8-11 (H) - G58-17 (HEAD) Below 1 Ω
G8-11 (H) or G58-17 (HEAD) - Body ground 10 kΩ or higher
G8-19 (EL) - Body ground Below 1 Ω




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR