Home › Vehicle Interior › LIGHTING › LIGHTING SYSTEM(except LED Headlight) › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059564 LIGHTING _0291933 LIGHTING SYSTEM(except LED Headlight) J

LIGHTING  LIGHTING SYSTEM(except LED Headlight)  Turn Signal Light Circuit  


DESCRIPTION

The turn signal flasher relay turns on when it receives signals from the headlight dimmer switch integrated with the turn signal switch, causing the turn signal lights to flash.

WIRING DIAGRAM

E132458E08
1.344,6.406 0.698,6.583 0.698,6.583 0.698,6.688 false 4.427,6.323 3.99,6.396 false 0.313,1.844 0.813,2 0.5,0.156 10 false G8 1.698,1.844 2.052,2 0.354,0.156 10 false 12*1 1.698,2.01 2.052,2.167 0.354,0.156 10 false 19*2 2.104,1.844 2.458,2 0.354,0.156 10 false 15*1 2.104,2.01 2.458,2.167 0.354,0.156 10 false 18*2 2.49,1.844 2.844,2 0.354,0.156 10 false 13*1 2.49,2.01 2.844,2.167 0.354,0.156 10 false 16*2 0.313,2.01 1.521,2.396 1.208,0.385 10 false Headlight Dimmer Switch 0.5,0.677 1.229,0.99 0.729,0.313 10 false Turn Signal Switch 1.271,1.052 1.51,1.219 0.24,0.167 10 false RH 1.271,0.646 1.5,0.792 0.229,0.146 10 false LH 1.594,0.354 1.844,0.51 0.25,0.156 10 false EL 2.281,0.354 2.552,0.5 0.271,0.146 10 false TR 1.917,0.354 2.188,0.5 0.271,0.146 10 false TL 5.25,1.125 5.99,1.302 0.74,0.177 10 false RH ECU-IG 6.031,1.844 6.667,2 0.635,0.156 10 false TRN HAZ 0.365,5.125 1.125,5.625 0.76,0.5 10 false Front Turn Signal Light Bulb RH 0.365,4.958 0.646,5.125 0.281,0.167 10 false B23 0.104,5 0.208,5.167 0.104,0.167 10 false 2 1.156,6.635 1.333,6.802 0.177,0.167 10 false 11 1.396,6.635 1.573,6.802 0.177,0.167 10 false W 1.156,6.031 1.333,6.198 0.177,0.167 10 false 10 1.396,6.031 1.573,6.198 0.177,0.167 10 false P 0.104,5.51 0.208,5.677 0.104,0.167 10 false 1 2.938,4.094 4.292,4.417 1.354,0.323 10 false Rear Turn Signal Light Bulb RH 6.271,3.125 7.125,3.281 0.854,0.156 10 false from Battery 4.76,0.969 4.948,1.135 0.188,0.167 10 false IG 4.833,1.688 5,1.854 0.167,0.167 10 false B 4.323,2.24 4.594,2.406 0.271,0.167 10 false LR 4.76,2.406 4.958,2.573 0.198,0.167 10 false LL 4.323,1.688 4.594,1.844 0.271,0.156 10 false EL 4.323,0.969 4.594,1.125 0.271,0.156 10 false ER 4.104,1.083 4.25,1.24 0.146,0.156 10 false 6 5.073,1.083 5.219,1.24 0.146,0.156 10 false 1 4.104,1.792 4.25,1.948 0.146,0.156 10 false 5 5.073,1.792 5.219,1.948 0.146,0.156 10 false 4 4.104,2.063 4.25,2.219 0.146,0.156 10 false 7 4.104,2.333 4.25,2.49 0.146,0.156 10 false 2 4.094,2.74 4.385,2.896 0.292,0.156 10 false G41 5.073,2.51 5.219,2.667 0.146,0.156 10 false 3 4.323,1.948 4.677,2.104 0.354,0.156 10 false E 0.323,6.719 1.104,7.229 0.781,0.51 10 false Side Turn Signal Light RH 1.573,6.313 2.74,6.635 1.167,0.323 10 false Outer Rear View Mirror RH 1.573,6.156 1.74,6.302 0.167,0.146 10 false I2 3.344,7.333 4.115,7.823 0.771,0.49 10 false Front Turn Signal Light Bulb LH 5.833,4.604 6.906,4.958 1.073,0.354 10 false Rear Turn Signal Light Bulb LH 1.625,3.042 3.156,3.188 1.531,0.146 10 false *1: for LHD, *2: for RHD 3.208,6.146 3.99,6.625 0.781,0.479 10 false Side Turn Signal Light LH 6.396,0.823 7.063,1.427 0.667,0.604 10 false from RH-IG Relay 1 4.094,2.906 5.104,3.24 1.01,0.333 10 false Turn Signal Flasher Relay 4.229,6.542 4.406,6.708 0.177,0.167 10 false 11 4.229,5.938 4.406,6.104 0.177,0.167 10 false 10 4.469,6.542 4.646,6.708 0.177,0.167 10 false W 4.469,5.938 4.646,6.104 0.177,0.167 10 false P 4.635,6.219 5.604,6.594 0.969,0.375 10 false Outer Rear View Mirror LH 4.635,6.073 5.031,6.219 0.396,0.146 10 false J2 3.344,7.167 3.635,7.333 0.292,0.167 10 false B22 2.938,3.938 3.406,4.104 0.469,0.167 10 false N22 3.042,7.281 3.146,7.448 0.104,0.167 10 false 2 3.042,7.792 3.146,7.958 0.104,0.167 10 false 1 2.656,3.917 2.76,4.083 0.104,0.167 10 false 4 2.656,4.438 2.76,4.604 0.104,0.167 10 false 3 5.833,4.448 6.302,4.615 0.469,0.167 10 false M8 5.573,4.427 5.677,4.594 0.104,0.167 10 false 4 5.573,4.938 5.677,5.104 0.104,0.167 10 false 3

PROCEDURE

1.CHECK OPERATION OF TURN SIGNAL LIGHT
a.

When the headlight dimmer switch (turn signal light switch) is operated, check that the appropriate turn signal light flashes.

Result
Condition Proceed to
All lights do not flash A
LH turn signal lights do not flash B
RH turn signal lights do not flash C
Any one of turn signal lights does not flash D



A

2.INSPECT FUSE (RH ECU-IG, TRN HAZ)

B

6.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY

C

9.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY

D

12.IDENTIFY MALFUNCTIONING PART
2.INSPECT FUSE (RH ECU-IG, TRN HAZ)
a.

Remove the RH ECU-IG fuse from the instrument panel junction block RH.


b.

Remove the TRN HAZ fuse from the engine room No. 1 relay block.


c.

Measure the resistance of the fuses.

Standard resistance:

Below 1 Ω




OK

3.CHECK WIRE HARNESS (BATTERY - TURN SIGNAL FLASHER RELAY)

NG

REPLACE FUSE

3.CHECK WIRE HARNESS (BATTERY - TURN SIGNAL FLASHER RELAY)
U189808E02
1.417,1.24 0.875,0.969 false 1.417,1.417 0.708,1.417 false 0.073,0.063 1.438,0.302 1.365,0.24 10 false Wire Harness Side: 1.552,0.771 1.885,0.948 0.333,0.177 10 false G41 0.677,0.865 0.938,1.052 0.26,0.188 10 false IG 0.531,1.344 0.698,1.531 0.167,0.188 10 false B

a.

Disconnect the G41 turn signal flasher relay connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
G41-1 (IG) - Body ground Ignition switch on (IG) 10 to 14 V
G41-4 (B) - Body ground Always 10 to 14 V




OK

4.INSPECT HEADLIGHT DIMMER SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT HEADLIGHT DIMMER SWITCH
B128006E48
2.281,1.188 2.802,0.438 false 2.115,1.271 2.5,1.698 false 1.781,1.24 2.115,1.896 false 1.625,1.24 1.49,1.875 false 1.271,1.24 0.781,1.865 false 1.115,1.198 0.542,0.344 false 0.104,2.896 0.896,3.073 0.792,0.177 10 false *1: for LHD 2.854,0.313 3.198,0.51 0.344,0.198 10 false EL*1 2.521,1.708 3.083,1.896 0.563,0.188 10 false TR*1 2.031,1.927 2.448,2.115 0.417,0.188 10 false TL*1 1.354,1.906 1.75,2.083 0.396,0.177 10 false TR*2 0.594,1.906 1.094,2.052 0.5,0.146 10 false TL*2 0.208,0.271 0.688,0.49 0.479,0.219 10 false EL*2 0.115,3.146 0.885,3.313 0.771,0.167 10 false *2: for RHD

a.

Remove the headlight dimmer switch.


b.

Measure the resistance of the switch.

Standard resistance:
for LHD
Tester Connection Condition Specified Condition
13 (TR) - 12 (EL) Right turn Below 1 Ω
15 (TL) - 12 (EL) Left turn Below 1 Ω
13 (TR) - 12 (EL) Neutral 10 kΩ or higher
15 (TL) - 12 (EL) Neutral 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
16 (TR) - 19 (EL) Right turn Below 1 Ω
18 (TL) - 19 (EL) Left turn Below 1 Ω
16 (TR) - 19 (EL) Neutral 10 kΩ or higher
18 (TL) - 19 (EL) Neutral 10 kΩ or higher




OK

5.CHECK WIRE HARNESS (DIMMER SWITCH - TURN SIGNAL FLASHER RELAY AND BODY GROUND)

NG

REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY

5.CHECK WIRE HARNESS (DIMMER SWITCH - TURN SIGNAL FLASHER RELAY AND BODY GROUND)
a.
U188742E02
1.521,3.26 1.021,3.521 false 1.677,3.26 2.292,3.49 false 1.25,1.792 0.667,1.844 false 1.385,1.823 1.094,2.125 false 1.604,1.802 1.604,2.115 false 2.115,1.802 2.458,1.594 2.458,1.594 2.594,1.594 false 1.74,1.823 2.198,2.146 false 2,1.771 2.156,1.281 2.156,1.281 2.521,1.281 false 0.104,0.115 1.458,0.271 1.354,0.156 10 false Wire Harness Side: 0.917,2.583 2.563,2.813 1.646,0.229 10 false Turn Signal Flasher Relay 0.76,3.094 1.052,3.24 0.292,0.146 10 false G41 0.865,3.542 1.073,3.74 0.208,0.198 10 false EL 2.313,3.5 2.625,3.646 0.313,0.146 10 false ER 0.125,4.083 0.854,4.26 0.729,0.177 10 false *1: for LHD 0.365,1.781 0.708,1.938 0.344,0.156 10 false EL*1 0.76,2.198 1.146,2.354 0.385,0.156 10 false TR*1 1.448,2.156 1.865,2.313 0.417,0.156 10 false TL*1 2.313,2.188 2.656,2.365 0.344,0.177 10 false TR*2 2.583,1.219 2.969,1.365 0.385,0.146 10 false TL*2 2.635,1.542 3.01,1.698 0.375,0.156 10 false EL*2 0.906,0.823 2.469,1.052 1.563,0.229 10 false Headlight Dimmer Switch 0.594,1.417 0.885,1.563 0.292,0.146 10 false G8 0.104,4.333 0.865,4.521 0.76,0.188 10 false *2: for RHD

Disconnect the G8 headlight dimmer switch connector.


b.

Disconnect the G41 turn signal flasher relay connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
for LHD
Tester Connection Specified Condition
G8-13 (TR) - G41-6 (ER) Below 1 Ω
G8-13 (TR) or G41-6 (ER) - Body ground 10 kΩ or higher
G8-15 (TL) - G41-5 (EL) Below 1 Ω
G8-15 (TL) or - G41-5 (EL) - Body ground 10 kΩ or higher
G8-12 (EL) - Body ground Below 1 Ω

for RHD
Tester Connection Specified Condition
G8-16 (TR) - G41-6 (ER) Below 1 Ω
G8-16 (TR) or G41-6 (ER) - Body ground 10 kΩ or higher
G8-18 (TL) - G41-5 (EL) Below 1 Ω
G8-18 (TL) or - G41-5 (EL) - Body ground 10 kΩ or higher
G8-19 (EL) - Body ground Below 1 Ω




OK

REPLACE TURN SIGNAL FLASHER RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY
B128006E49
0.76,1.979 1.281,1.229 false 1.792,1.219 2.125,1.875 false 2.781,0.604 2.292,1.229 false 1.156,1.229 0.583,0.375 false 0.104,2.833 0.844,3.01 0.74,0.177 10 false *1: for LHD 2.833,0.458 3.177,0.656 0.344,0.198 10 false EL*1 2,1.885 2.417,2.073 0.417,0.188 10 false TL*1 0.521,2.01 1.021,2.156 0.5,0.146 10 false TL*2 0.208,0.24 0.688,0.458 0.479,0.219 10 false EL*2 0.094,3.115 0.865,3.281 0.771,0.167 10 false *2: for RHD

a.

Remove the headlight dimmer switch.


b.

Measure the resistance of the switch.

Standard resistance:
for LHD
Tester Connection Condition Specified Condition
15 (TL) - 12 (EL) Left turn Below 1 Ω
15 (TL) - 12 (EL) Neutral 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
18 (TL) - 19 (EL) Left turn Below 1 Ω
18 (TL) - 19 (EL) Neutral 10 kΩ or higher




OK

7.CHECK WIRE HARNESS (DIMMER SWITCH - TURN SIGNAL FLASHER RELAY AND BODY GROUND)

NG

REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY

7.CHECK WIRE HARNESS (DIMMER SWITCH - TURN SIGNAL FLASHER RELAY AND BODY GROUND)
a.
U188743E02
1.552,3.26 1.052,3.521 false 1.271,1.802 0.688,1.854 false 1.625,1.813 1.625,2.125 false 2.125,1.792 2.469,1.583 2.469,1.583 2.604,1.583 false 2.01,1.781 2.167,1.292 2.167,1.292 2.531,1.292 false 0.219,0.135 1.573,0.292 1.354,0.156 10 false Wire Harness Side: 0.823,2.563 2.5,2.729 1.677,0.167 10 false Turn Signal Flasher Relay 0.76,3.083 1.052,3.229 0.292,0.146 10 false G41 0.917,3.552 1.146,3.76 0.229,0.208 10 false EL 0.083,4.094 0.802,4.271 0.719,0.177 10 false *1: for LHD 0.333,1.813 0.677,1.969 0.344,0.156 10 false EL*1 1.469,2.156 1.885,2.313 0.417,0.156 10 false TL*1 2.552,1.198 2.938,1.344 0.385,0.146 10 false TL*2 2.667,1.51 3.042,1.667 0.375,0.156 10 false EL*2 0.917,0.792 2.5,0.99 1.583,0.198 10 false Headlight Dimmer Switch 0.573,1.427 0.865,1.573 0.292,0.146 10 false G8 0.083,4.365 0.875,4.531 0.792,0.167 10 false *2: for RHD

Disconnect the G8 headlight dimmer switch connector.


b.

Disconnect the G41 turn signal flasher relay connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
for LHD
Tester Connection Specified Condition
G8-15 (TL) - G41-5 (EL) Below 1 Ω
G8-15 (TL) or - G41-5 (EL) - Body ground 10 kΩ or higher
G8-12 (EL) - Body ground Below 1 Ω

for RHD
Tester Connection Specified Condition
G8-18 (TL) - G41-5 (EL) Below 1 Ω
G8-18 (TL) or - G41-5 (EL) - Body ground 10 kΩ or higher
G8-19 (EL) - Body ground Below 1 Ω




OK

8.CHECK WIRE HARNESS (EACH LIGHT - TURN SIGNAL FLASHER RELAY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK WIRE HARNESS (EACH LIGHT - TURN SIGNAL FLASHER RELAY AND BODY GROUND)
a.

Disconnect the B22, J2 and M8 light connectors.

U189930E02
3.438,1.458 3.438,1.948 false 3.323,1.438 3.156,1.927 false 3.781,3.25 4.073,3.25 false 0.083,0.042 1.469,0.208 1.385,0.167 10 false Wire Harness Side: 0.635,0.5 2.292,0.667 1.656,0.167 10 false Front Turn Signal Light LH 0.635,1.302 0.938,1.469 0.302,0.167 10 false B22 2.635,1.302 2.844,1.469 0.208,0.167 10 false J2 3.021,1.948 3.229,2.115 0.208,0.167 10 false W 4.115,3.177 4.51,3.344 0.396,0.167 10 false LL 3.406,1.938 3.615,2.104 0.208,0.167 10 false P 5.198,1.302 5.458,1.469 0.26,0.167 10 false M8 2.698,3.24 3.021,3.406 0.323,0.167 10 false G41 2.729,0.208 4.573,0.375 1.844,0.167 10 false Outer Rear View Mirror LH 2.729,2.563 4.573,2.729 1.844,0.167 10 false Turn Signal Flasher Relay 5.083,0.208 6.927,0.375 1.844,0.167 10 false Rear Turn Signal Light LH 2.729,0.542 4.573,0.708 1.844,0.167 10 false (Side Turn Signal Light LH)


b.

Disconnect the G41 turn signal flasher relay connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
B22-2 - G41-3 (LL) Below 1 Ω
J2-10 - G41-3 (LL) Below 1 Ω
M8-4 - G41-3 (LL) Below 1 Ω
B22-2 or G41-3 (LL) - Body ground 10 kΩ or higher
J2-10 or G41-3 (LL) - Body ground 10 kΩ or higher
M8-4 or G41-3 (LL) - Body ground 10 kΩ or higher
B22-1 - Body ground Below 1 Ω
J2-11 - Body ground Below 1 Ω
M8-3 - Body ground Below 1 Ω




OK

REPLACE TURN SIGNAL FLASHER RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY
B128006E50
2.281,1.177 2.802,0.427 false 2.125,1.229 2.51,1.656 false 1.625,1.219 1.49,1.854 false 1.125,1.208 0.552,0.354 false 0.115,2.854 0.833,3.031 0.719,0.177 10 false *1: for LHD 2.813,0.271 3.156,0.469 0.344,0.198 10 false EL*1 2.542,1.698 3.104,1.885 0.563,0.188 10 false TR*1 1.333,1.906 1.729,2.083 0.396,0.177 10 false TR*2 0.198,0.24 0.677,0.458 0.479,0.219 10 false EL*2 0.115,3.104 0.844,3.26 0.729,0.156 10 false *2: for RHD

a.

Remove the headlight dimmer switch.


b.

Measure the resistance of the switch.

Standard resistance:
for LHD
Tester Connection Condition Specified Condition
13 (TR) - 12 (EL) Right turn Below 1 Ω
13 (TR) - 12 (EL) Neutral 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
16 (TR) - 19 (EL) Right turn Below 1 Ω
16 (TR) - 19 (EL) Neutral 10 kΩ or higher




OK

10.CHECK WIRE HARNESS (DIMMER SWITCH - TURN SIGNAL FLASHER RELAY AND BODY GROUND)

NG

REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY

10.CHECK WIRE HARNESS (DIMMER SWITCH - TURN SIGNAL FLASHER RELAY AND BODY GROUND)
a.
U188744E02
1.677,3.271 2.292,3.5 false 1.25,1.792 0.667,1.844 false 1.396,1.802 1.104,2.104 false 2.146,1.792 2.49,1.583 2.49,1.583 2.625,1.583 false 1.771,1.813 2.229,2.135 false 0.104,0.135 1.458,0.292 1.354,0.156 10 false Wire Harness Side: 0.896,2.583 2.573,2.75 1.677,0.167 10 false Turn Signal Flasher Relay 0.76,3.083 1.052,3.229 0.292,0.146 10 false G41 2.333,3.51 2.646,3.656 0.313,0.146 10 false ER 0.094,4.083 0.833,4.26 0.74,0.177 10 false *1: for LHD 0.281,1.781 0.625,1.938 0.344,0.156 10 false EL*1 0.927,2.146 1.313,2.302 0.385,0.156 10 false TR*1 2.292,2.156 2.635,2.333 0.344,0.177 10 false TR*2 2.688,1.531 3.063,1.688 0.375,0.156 10 false EL*2 0.875,0.813 2.458,0.969 1.583,0.156 10 false Headlight Dimmer Switch 0.583,1.427 0.875,1.573 0.292,0.146 10 false G8 0.094,4.313 0.833,4.5 0.74,0.188 10 false *2: for RHD

Disconnect the G8 headlight dimmer switch connector.


b.

Disconnect the G41 turn signal flasher relay connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
for LHD
Tester Connection Specified Condition
G8-13 (TR) - G41-6 (ER) Below 1 Ω
G8-13 (TR) or G41-6 (ER) - Body ground 10 kΩ or higher
G8-12 (EL) - Body ground Below 1 Ω

for RHD
Tester Connection Specified Condition
G8-16 (TR) - G41-6 (ER) Below 1 Ω
G8-16 (TR) or G41-6 (ER) - Body ground 10 kΩ or higher
G8-19 (EL) - Body ground Below 1 Ω




OK

11.CHECK WIRE HARNESS (EACH LIGHT - TURN SIGNAL FLASHER RELAY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK WIRE HARNESS (EACH LIGHT - TURN SIGNAL FLASHER RELAY AND BODY GROUND)
a.

Disconnect the B23, I2 and N22 light connectors.

U189931E01
0.086,0.065 1.474,0.230 1.387,0.165 10 Wire Harness Side: 0.637,0.532 2.312,0.697 1.674,0.165 10 Front Turn Signal Light RH 0.628,1.298 0.898,1.463 0.270,0.165 10 B23 2.636,1.298 2.843,1.463 0.207,0.165 10 I2 3.019,1.943 3.226,2.108 0.207,0.165 10 W 4.112,3.553 4.509,3.718 0.397,0.165 10 LR 3.402,1.943 3.609,2.108 0.207,0.165 10 P 5.18,1.298 5.462,1.463 0.282,0.165 10 N22 2.692,3.241 3.010,3.406 0.318,0.165 10 G41 2.73,0.233 4.571,0.399 1.841,0.165 10 Outer Rear View Mirror RH 2.73,2.587 4.571,2.752 1.841,0.165 10 Turn Signal Flasher Relay 5.083,0.233 6.925,0.399 1.841,0.165 10 Rear Turn Signal Light RH 2.73,0.57 4.571,0.735 1.841,0.165 10 (Side Turn Signal Light RH) 3.441,1.445 3.441,1.933 false 3.327,1.445 3.159,1.933 false 4.075,3.626 3.575,3.626 3.575,3.626 3.488,3.292 false


b.

Disconnect the G41 turn signal flasher relay connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
B23-2 - G41-2 (LR) Below 1 Ω
I2-10 - G41-2 (LR) Below 1 Ω
N22-4 - G41-2 (LR) Below 1 Ω
B23-2 or G41-2 (LR) - Body ground 10 kΩ or higher
I2-10 or G41-2 (LR) - Body ground 10 kΩ or higher
N22-4 or G41-2 (LR) - Body ground 10 kΩ or higher
B23-1 - Body ground Below 1 Ω
I2-11 - Body ground Below 1 Ω
N22-3 - Body ground Below 1 Ω




OK

REPLACE TURN SIGNAL FLASHER RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.IDENTIFY MALFUNCTIONING PART
a.

Check which light does not illuminate.

Result
result Proceed to
Front turn signal light does not illuminate A
Side turn signal light does not illuminate B
Rear turn signal light does not illuminate C



A

13.REPLACE FRONT TURN SIGNAL LIGHT BULB

B

15.CHECK WIRE HARNESS (SIDE TURN SIGNAL LIGHT - FLASHER RELAY AND BODY GROUND)

C

16.REPLACE REAR TURN SIGNAL LIGHT BULB
13.REPLACE FRONT TURN SIGNAL LIGHT BULB
a.

Replace the front turn signal light bulb with a new one.


b.

Check that the bulb illuminates normally.

OK:

Bulb illuminates.




NG

14.INSPECT FRONT TURN SIGNAL LIGHT SOCKET

OK

END

14.INSPECT FRONT TURN SIGNAL LIGHT SOCKET
a.
E187621E01
0.713,1.471 1.428,1.671 0.714,0.200 10 Battery (+) 1.894,1.437 2.608,1.637 0.714,0.200 10 Battery (-) 1.551,0.998 1.162,1.436 false 1.921,0.963 2.311,1.401 false

Remove the front turn signal light socket with bulb.


b.

Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1. Then check that the bulb illuminates.

OK:

Bulb illuminates.




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT TURN SIGNAL LIGHT - FLASHER RELAY AND BODY GROUND)

NG

REPLACE FRONT TURN SIGNAL LIGHT SOCKET

15.CHECK WIRE HARNESS (SIDE TURN SIGNAL LIGHT - FLASHER RELAY AND BODY GROUND)
a.
U189907E02
1.531,1.771 1.531,2.281 false 1.917,3.521 2.292,3.521 false 1.406,1.771 1.188,2.281 false 0.083,0.031 1.542,0.177 1.458,0.146 10 false Wire Harness Side: 0.781,0.396 2.458,0.542 1.677,0.146 10 false Outer Rear View Mirror LH 0.844,2.688 2.521,2.833 1.677,0.146 10 false Turn Signal Flasher Relay 0.781,0.771 2.49,0.917 1.708,0.146 10 false (Side Turn Signal Light LH) 1.469,2.323 1.625,2.469 0.156,0.146 10 false P 1.063,2.323 1.219,2.469 0.156,0.146 10 false W 2.323,3.438 2.521,3.583 0.198,0.146 10 false LL 0.698,1.531 0.875,1.677 0.177,0.146 10 false J2 0.583,3.5 0.875,3.646 0.292,0.146 10 false G41

for LH:

i.

Disconnect the J2 mirror connector.


ii.

Disconnect the G41 relay connector.


iii.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
J2-10 (P) - G41-3 (LL) Below 1 Ω
J2-10 (P) or G41-3 (LL) - Body ground 10 kΩ or higher
J2-11 (W) - Body ground 10 kΩ or higher




b.
U189908E01
0.087,0.059 1.541,0.201 1.454,0.142 10 Wire Harness Side: 0.782,0.42 2.494,0.562 1.712,0.142 10 Outer Rear View Mirror RH 0.84,2.746 2.514,2.888 1.674,0.142 10 Turn Signal Flasher Relay 0.782,0.798 2.525,0.940 1.743,0.142 10 (Side Turn Signal Light RH) 1.465,2.345 1.617,2.487 0.152,0.142 10 P 1.064,2.345 1.216,2.487 0.152,0.142 10 W 2.195,4.102 2.393,4.245 0.198,0.142 10 LR 0.716,1.555 0.893,1.698 0.176,0.142 10 I2 0.587,3.525 0.882,3.667 0.295,0.142 10 G41 1.534,1.795 1.534,2.311 false 2.172,4.183 1.745,4.183 1.745,4.183 1.566,3.572 false 1.408,1.795 1.19,2.311 false

for RH:

i.

Disconnect the I2 mirror connector.


ii.

Disconnect the G41 relay connector.


iii.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
I2-10 (P) - G41-2 (LR) Below 1 Ω
I2-10 (P) or G41-2 (LR) - Body ground 10 kΩ or higher
I2-11 (W) - Body ground 10 kΩ or higher





OK

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.REPLACE REAR TURN SIGNAL LIGHT BULB
a.

Replace the rear turn signal light bulb with a new one.


b.

Check that the bulb illuminates normally.

OK:

Bulb illuminates.




NG

17.INSPECT REAR TURN SIGNAL LIGHT SOCKET

OK

END

17.INSPECT REAR TURN SIGNAL LIGHT SOCKET
a.

Remove the rear combination light socket with bulb.


E133734E02
0.257,1.4 0.986,1.570 0.729,0.170 10 Battery (+) 2.44,1.4 3.193,1.570 0.753,0.170 10 Battery (-) 1.908,1.347 2.388,1.45 false 1.652,1.347 1.171,1.45 false

b.

Connect the positive (+) lead from the battery to terminal 4 and the negative (-) lead to terminal 3. Then check that the bulb illuminates.

OK:

Bulb illuminates.




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR TURN SIGNAL LIGHT - FLASHER RELAY AND BODY GROUND)

NG

REPLACE REAR TURN SIGNAL LIGHT SOCKET